From: Masami Hiramatsu <masami.hiramatsu@linaro.org>
To: Peng Fan <peng.fan@nxp.com>, Simon Glass <sjg@chromium.org>,
Tom Rini <trini@konsulko.com>,
Heinrich Schuchardt <xypron.glpk@gmx.de>,
Alexander Graf <agraf@csgraf.de>,
Jagan Teki <jagan@amarulasolutions.com>,
Vignesh R <vigneshr@ti.com>,
Joe Hershberger <joe.hershberger@ni.com>,
Ramon Fried <rfried.dev@gmail.com>,
Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>,
Jassi Brar <jaswinder.singh@linaro.org>,
Ilias Apalodimas <ilias.apalodimas@linaro.org>,
Masahisa Kojima <masahisa.kojima@linaro.org>,
Takahiro Akashi <takahiro.akashi@linaro.org>,
Tim Harvey <tharvey@gateworks.com>, Bin Meng <bmeng.cn@gmail.com>,
u-boot@lists.denx.de, Jaehoon Chung <jh80.chung@samsung.com>
Subject: [PATCH v5 11/13] board: synquacer: Add DeveloperBox 96boards EE support
Date: Fri, 4 Jun 2021 18:45:10 +0900 [thread overview]
Message-ID: <162279991017.518877.5412912119801083387.stgit@localhost> (raw)
In-Reply-To: <162279979193.518877.11119025270138617301.stgit@localhost>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
---
Changes in v5:
- Remove log level from config.
Changes in v4:
- Add I2C and RTC configuration.
- Enable RTC and Date command.
- Remove I2C0 node before booting linux to hide it same as EDK2 does.
- Add some configurations to make it EBBR compliant.
Changes in v3:
- Enable CONFIG_MMC_SDHCI_F_SDH30.
- Enable CONFIG_CMD_GENERIC (fstype command) for distro boot.
- Remove unneeded CONFIG_ONLY_GENERIC_GPIO.
Changes in v2:
- Do not include arch/gpio.h and remove arch-sc2a11/gpio.h.
- Remove non-UEFI boot commands.
- Use Distro boot.
- Remove NOR-connected SPI node by path instead of alias.
- Rename configs/SynQuacer_defconfig to
configs/synquacer_developerbox_defconfig.
- Rename include/configs/SynQuacer.h to include/configs/synquacer.h.
- Move README under doc/board/socionext/ and make it .rst text.
---
arch/arm/Kconfig | 14 +++
board/socionext/developerbox/Kconfig | 36 +++++++
board/socionext/developerbox/MAINTAINERS | 14 +++
board/socionext/developerbox/Makefile | 9 ++
board/socionext/developerbox/developerbox.c | 146 +++++++++++++++++++++++++++
configs/synquacer_developerbox_defconfig | 112 +++++++++++++++++++++
doc/board/index.rst | 1
doc/board/socionext/developerbox.rst | 87 ++++++++++++++++
doc/board/socionext/index.rst | 9 ++
include/configs/synquacer.h | 109 ++++++++++++++++++++
10 files changed, 537 insertions(+)
create mode 100644 board/socionext/developerbox/Kconfig
create mode 100644 board/socionext/developerbox/MAINTAINERS
create mode 100644 board/socionext/developerbox/Makefile
create mode 100644 board/socionext/developerbox/developerbox.c
create mode 100644 configs/synquacer_developerbox_defconfig
create mode 100644 doc/board/socionext/developerbox.rst
create mode 100644 doc/board/socionext/index.rst
create mode 100644 include/configs/synquacer.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 023824df77..7ff24535cd 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1760,6 +1760,19 @@ config ARCH_UNIPHIER
Support for UniPhier SoC family developed by Socionext Inc.
(formerly, System LSI Business Division of Panasonic Corporation)
+config ARCH_SYNQUACER
+ bool "Socionext SynQuacer SoCs"
+ select ARM64
+ select DM
+ select GIC_V3
+ select PSCI_RESET
+ select SYSRESET
+ select SYSRESET_PSCI
+ select OF_CONTROL
+ help
+ Support for SynQuacer SoC family developed by Socionext Inc.
+ This SoC is used on 96boards EE DeveloperBox.
+
config ARCH_STM32
bool "Support STMicroelectronics STM32 MCU with cortex M"
select CPU_V7M
@@ -2102,6 +2115,7 @@ source "board/hisilicon/poplar/Kconfig"
source "board/isee/igep003x/Kconfig"
source "board/kontron/sl28/Kconfig"
source "board/myir/mys_6ulx/Kconfig"
+source "board/socionext/developerbox/Kconfig"
source "board/spear/spear300/Kconfig"
source "board/spear/spear310/Kconfig"
source "board/spear/spear320/Kconfig"
diff --git a/board/socionext/developerbox/Kconfig b/board/socionext/developerbox/Kconfig
new file mode 100644
index 0000000000..706b8dc0f1
--- /dev/null
+++ b/board/socionext/developerbox/Kconfig
@@ -0,0 +1,36 @@
+if ARCH_SYNQUACER
+
+choice
+ prompt "SC2A11 Cortex-A53 MPCore 24cores"
+ optional
+
+config TARGET_DEVELOPERBOX
+ bool "Socionext DeveloperBox"
+ select PCI
+ select DM_PCI
+ select PCIE_ECAM_SYNQUACER
+ select SYS_DISABLE_DCACHE_OPS
+ select OF_BOARD_SETUP
+ help
+ Choose this option if you build the U-Boot for the DeveloperBox
+ 96boards Enterprise Edition.
+ This board will booted from SCP firmware and it enables SMMU, thus
+ the dcache is updated automatically when DMA operation is executed.
+endchoice
+
+config SYS_SOC
+ default "sc2a11"
+
+if TARGET_DEVELOPERBOX
+
+config SYS_BOARD
+ default "developerbox"
+
+config SYS_VENDOR
+ default "socionext"
+
+config SYS_CONFIG_NAME
+ default "synquacer"
+
+endif
+endif
diff --git a/board/socionext/developerbox/MAINTAINERS b/board/socionext/developerbox/MAINTAINERS
new file mode 100644
index 0000000000..aa672b6e05
--- /dev/null
+++ b/board/socionext/developerbox/MAINTAINERS
@@ -0,0 +1,14 @@
+DEVELOPER BOX
+M: Masami Hiramatsu <masami.hiramatsu@linaro.org>
+M: Jassi Brar <jaswinder.singh@linaro.org>
+S: Maintained
+F: arch/arm/dts/synquacer-*
+F: board/socionext/developerbox/*
+F: configs/synquacer_developerbox_defconfig
+F: drivers/i2c/synquacer_i2c.c
+F: drivers/mmc/f_sdh30.c
+F: drivers/net/sni_netsec.c
+F: drivers/pci/pcie_ecam_synquacer.c
+F: drivers/spi/spi-synquacer.c
+F: include/configs/synquacer.h
+F: doc/board/socionext/developerbox.rst
diff --git a/board/socionext/developerbox/Makefile b/board/socionext/developerbox/Makefile
new file mode 100644
index 0000000000..4a46de995a
--- /dev/null
+++ b/board/socionext/developerbox/Makefile
@@ -0,0 +1,9 @@
+#
+# Author: Masami Hiramatsu <masami.hiramatsu@linaro.org>
+#
+# Copyright (C) 2021 Linaro Ltd.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := developerbox.o
diff --git a/board/socionext/developerbox/developerbox.c b/board/socionext/developerbox/developerbox.c
new file mode 100644
index 0000000000..34335baec3
--- /dev/null
+++ b/board/socionext/developerbox/developerbox.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * u-boot/board/socionext/developerbox/developerbox.c
+ *
+ * Copyright (C) 2016-2017 Socionext Inc.
+ * Copyright (C) 2021 Linaro Ltd.
+ */
+#include <asm/types.h>
+#include <asm/armv8/mmu.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <common.h>
+#include <env_internal.h>
+#include <fdt_support.h>
+#include <log.h>
+
+static struct mm_region sc2a11_mem_map[] = {
+ {
+ .virt = 0x0UL,
+ .phys = 0x0UL,
+ .size = 0x80000000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_OUTER_SHARE
+ }, {
+ /* 1st DDR block */
+ .virt = 0x80000000UL,
+ .phys = 0x80000000UL,
+ .size = PHYS_SDRAM_SIZE,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_OUTER_SHARE
+ }, {
+ /* 2nd DDR place holder */
+ 0,
+ }, {
+ /* 3rd DDR place holder */
+ 0,
+ }, {
+ /* List terminator */
+ 0,
+ }
+};
+
+struct mm_region *mem_map = sc2a11_mem_map;
+
+#define DDR_REGION_INDEX(i) (1 + (i))
+#define MAX_DDR_REGIONS 3
+
+struct draminfo_entry {
+ u64 base;
+ u64 size;
+};
+
+struct draminfo {
+ u32 nr_regions;
+ u32 reserved;
+ struct draminfo_entry entry[3];
+};
+
+struct draminfo *synquacer_draminfo = (void *)SQ_DRAMINFO_BASE;
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define LOAD_OFFSET 0x100
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+int board_init(void)
+{
+ gd->bd->bi_boot_params = CONFIG_SYS_LOAD_ADDR + LOAD_OFFSET;
+
+ gd->env_addr = (ulong)&default_environment[0];
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ /* Remove SPI NOR and I2C0 for making DT compatible with EDK2 */
+ fdt_del_node_and_alias(blob, "spi_nor");
+ fdt_del_node_and_alias(blob, "i2c0");
+
+ return 0;
+}
+
+/*
+ * DRAM configuration
+ */
+
+int dram_init(void)
+{
+ struct draminfo_entry *ent = synquacer_draminfo->entry;
+ struct mm_region *mr;
+ int i, ri;
+
+ if (synquacer_draminfo->nr_regions < 1) {
+ log_err("Failed to get correct DRAM information\n");
+ return -1;
+ }
+
+ /*
+ * U-Boot RAM size must be under the first DRAM region so that it doesn't
+ * access secure memory which is at the end of the first DRAM region.
+ */
+ gd->ram_size = ent[0].size;
+
+ /* Update memory region maps */
+ for (i = 0; i < synquacer_draminfo->nr_regions; i++) {
+ if (i >= MAX_DDR_REGIONS)
+ break;
+
+ ri = DDR_REGION_INDEX(i);
+ mem_map[ri].phys = ent[i].base;
+ mem_map[ri].size = ent[i].size;
+ if (i == 0)
+ continue;
+
+ mr = &mem_map[DDR_REGION_INDEX(0)];
+ mem_map[ri].virt = mr->virt + mr->size;
+ mem_map[ri].attrs = mr->attrs;
+ }
+
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ struct draminfo_entry *ent = synquacer_draminfo->entry;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(gd->bd->bi_dram); i++) {
+ if (i < synquacer_draminfo->nr_regions) {
+ debug("%s: dram[%d] = %llx@%llx\n", __func__, i, ent[i].size, ent[i].base);
+ gd->bd->bi_dram[i].start = ent[i].base;
+ gd->bd->bi_dram[i].size = ent[i].size;
+ }
+ }
+
+ return 0;
+}
+
+int print_cpuinfo(void)
+{
+ printf("CPU: SC2A11:Cortex-A53 MPCore 24cores\n");
+ return 0;
+}
diff --git a/configs/synquacer_developerbox_defconfig b/configs/synquacer_developerbox_defconfig
new file mode 100644
index 0000000000..cbc09d3225
--- /dev/null
+++ b/configs/synquacer_developerbox_defconfig
@@ -0,0 +1,112 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SYNQUACER=y
+CONFIG_SYS_TEXT_BASE=0x08200000
+CONFIG_ENV_SIZE=0x30000
+CONFIG_ENV_OFFSET=0x300000
+CONFIG_DEBUG_UART_BASE=0x2a400000
+CONFIG_DEBUG_UART_CLOCK=62500000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_DEVELOPERBOX=y
+CONFIG_DEFAULT_DEVICE_TREE="synquacer-sc2a11-developerbox"
+CONFIG_AHCI=y
+CONFIG_BOOTSTAGE_STASH_SIZE=4096
+CONFIG_BOOTM_EFI=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTEFI=y
+CONFIG_CMD_NVEDIT_EFI=y
+CONFIG_CMD_EFIDEBUG=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_IMLS=y
+CONFIG_CMD_NVEDIT_INFO=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_NET=y
+CONFIG_CMD_BOOTP=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_DATE=y
+CONFIG_CMD_RTC=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_POWEROFF=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_SATA=y
+CONFIG_CMD_NVME=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDPARTS_DEFAULT="nor1:448k(BootStrap-BL1),576k(Flash-Writer),512k(SCP-BL2),480k(FIP-TFA),32k(Stg2-Tables),1m@2m(U-Boot),1m@3m(UBoot-Env),2m@5m(Ex-OPTEE)"
+CONFIG_MTDIDS_DEFAULT="nor1=nor1"
+CONFIG_CMD_LOG=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_EFI_PARTITION=y
+CONFIG_EFI_LOADER=y
+CONFIG_EFI_DEVICE_PATH_TO_TEXT=y
+CONFIG_EFI_UNICODE_COLLATION_PROTOCOL2=y
+CONFIG_EFI_UNICODE_CAPITALIZATION=y
+CONFIG_EFI_HAVE_RUNTIME_RESET=y
+CONFIG_EFI_GET_TIME=y
+CONFIG_EFI_SET_TIME=y
+CONFIG_CMD_EFI_VARIABLE_FILE_STORE=Y
+CONFIG_OF_SEPARATE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_PROT_UDP=y
+CONFIG_BAUDRATE=115200
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_CONS_INDEX=0
+CONFIG_DM_SERIAL=y
+CONFIG_PL01X_SERIAL=y
+CONFIG_SATA=y
+CONFIG_NVME=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_SYNQUACER=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_F_SDH30=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_SPEED=31250000
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHYLIB=y
+CONFIG_PHYLIB_10G=y
+CONFIG_NET=y
+CONFIG_NETDEVICES=y
+CONFIG_SNI_NETSEC=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_PHY_GIGE=y
+CONFIG_RGMII=y
+CONFIG_MII=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_PCF8563=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_SYNQUACER_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_PCI=y
+CONFIG_USB_STORAGE=y
diff --git a/doc/board/index.rst b/doc/board/index.rst
index a70d2de19d..242372b321 100644
--- a/doc/board/index.rst
+++ b/doc/board/index.rst
@@ -21,6 +21,7 @@ Board-specific doc
rockchip/index
sifive/index
sipeed/index
+ socionext/index
st/index
tbs/index
toradex/index
diff --git a/doc/board/socionext/developerbox.rst b/doc/board/socionext/developerbox.rst
new file mode 100644
index 0000000000..2d943c23be
--- /dev/null
+++ b/doc/board/socionext/developerbox.rst
@@ -0,0 +1,87 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Introduction
+============
+
+DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
+
+* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
+* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
+* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
+ (1x slots are connected via PCIe bridge chip)
+* 4 USB-3.0 ports
+* 2 SATA ports
+* 1 GbE network port
+* 1 USB-UART serial port (micro USB)
+* 64MB SPI NOR Flash
+* 8GB eMMC Flash Storage
+* 96boards LS connector
+
+The DeveloperBox schematic can be found here: -
+https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdf
+
+And the other documents can be found here: -
+https://www.96boards.org/documentation/enterprise/developerbox/
+
+
+Currently, the U-Boot port supports: -
+
+* USB
+* eMMC
+* SPI-NOR
+* SATA
+* GbE
+
+The DeveloperBox boots the TF-A and EDK2 as a main bootloader by default.
+The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as
+BL33, but no need to combine with it.
+
+Compile from source
+===================
+
+You can build U-Boot without any additinal source code.::
+
+ cd u-boot
+ export ARCH=arm64
+ export CROSS_COMPILE=aarch64-linux-gnu-
+ make SynQuacer_defconfig
+ make -j `noproc`
+
+Then, expand the binary to 1MB for preparing flash.::
+
+ cp u-boot.bin SPI_NOR_UBOOT.fd
+ truncate -s 1M SPI_NOR_UBOOT.fd
+
+Installation
+============
+
+You can install the SNI_NOR_UBOOT.fd via NOR flash writer.
+
+Flashing the U-Boot image on DeveloperBox requires a 96boards UART mezzanine or other mezzanine which can connect to LS-UART0 port.
+Connect USB cable from host to the LS-UART0 and set DSW2-7 to ON, and turn the board on again. The flash writer program will be started automatically; don’t forget to turn the DSW2-7 off again after flashing.
+
+*!!CAUTION!! If you failed to write the U-Boot image on wrong address, the board can be bricked. See below page if you need to recover the bricked board. See the following page for more detail*
+
+https://www.96boards.org/documentation/enterprise/developerbox/installation/board-recovery.md.html
+
+When the serial flasher is running correctly is will show the following boot messages shown via LS-UART0::
+
+
+ /*------------------------------------------*/
+ /* SC2A11 "SynQuacer" series Flash writer */
+ /* */
+ /* Version: cd254ac */
+ /* Build: 12/15/17 11:25:45 */
+ /*------------------------------------------*/
+
+ Command Input >
+
+Once the flasher tool is running we are ready flash the UEFI image::
+
+ flash rawwrite 200000 100000
+ >> Send SPI_NOR_UBOOT.fd via XMODEM (Control-A S in minicom) <<
+
+*!!NOTE!! The flasher command parameter is different from the command for board recovery. U-Boot uses the offset 200000 (2-five-0, 2M in hex) and the size 100000 (1-five-0, 1M in hex).*
+
+After transferring the SPI_NOR_UBOOT.fd, turn off the DSW2-7 and reset the board.
+
diff --git a/doc/board/socionext/index.rst b/doc/board/socionext/index.rst
new file mode 100644
index 0000000000..4673dcc45b
--- /dev/null
+++ b/doc/board/socionext/index.rst
@@ -0,0 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Socionext
+=========
+
+.. toctree::
+ :maxdepth: 2
+
+ developerbox
diff --git a/include/configs/synquacer.h b/include/configs/synquacer.h
new file mode 100644
index 0000000000..0dab4de1f1
--- /dev/null
+++ b/include/configs/synquacer.h
@@ -0,0 +1,109 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2016-2017 Socionext Inc.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* Timers for fasp(TIMCLK) */
+#define CONFIG_SYS_HZ 1000 /* 1 msec */
+#define CONFIG_SYS_TIMERBASE 0x31080000 /* AP Timer 1 (ARM-SP804) */
+
+/*
+ * SDRAM (for initialize)
+ */
+#define CONFIG_SYS_SDRAM_BASE (0x80000000) /* Start address of DDR3 */
+#define PHYS_SDRAM_SIZE (0x7c000000) /* Default size (2GB - Secure memory) */
+
+#define CONFIG_VERY_BIG_RAM /* SynQuacer supports up to 64GB */
+#define CONFIG_MAX_MEM_MAPPED PHYS_SDRAM_SIZE
+
+#define SQ_DRAMINFO_BASE (0x2e00ffc0) /* DRAM info from TF-A */
+
+/*
+ * Boot info
+ */
+#define CONFIG_SYS_INIT_SP_ADDR (0xe0000000) /* stack of init proccess */
+#define CONFIG_SYS_MALLOC_LEN (0x01000000) /* 16Mbyte size of malloc() */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* default kernel load address */
+
+/*
+ * Hardware drivers support
+ */
+
+/* RTC */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51
+
+/* Serial (pl011) */
+#define UART_CLK (62500000)
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_PL011_SERIAL
+#define CONFIG_PL011_CLOCK UART_CLK
+#define CONFIG_PL01x_PORTS {(void *)(0x2a400000)}
+
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+
+/* Support MTD */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_BASE (0x08000000)
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+
+#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + (512 * 1024))
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + PHYS_SDRAM_SIZE)
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200, 19200, 38400, 57600, 9600 }
+
+#define CONFIG_SYS_CBSIZE 1024
+#define CONFIG_SYS_MAXARGS 128
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Since U-Boot 64bit PCIe support is limited, disable 64bit MMIO support */
+/* #define CONFIG_SYS_PCI_64BIT 1 */
+
+/* Distro boot settings */
+#ifndef CONFIG_SPL_BUILD
+#ifdef CONFIG_CMD_USB
+#define BOOT_TARGET_DEVICE_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICE_USB(func)
+#endif
+
+#ifdef CONFIG_CMD_MMC
+#define BOOT_TARGET_DEVICE_MMC(func) func(MMC, mmc, 0)
+#else
+#define BOOT_TARGET_DEVICE_MMC(func)
+#endif
+
+#ifdef CONFIG_CMD_NVME
+#define BOOT_TARGET_DEVICE_NVME(func) func(NVME, nvme, 0)
+#else
+#define BOOT_TARGET_DEVICE_NVME(func)
+#endif
+
+#ifdef CONFIG_CMD_SCSI
+#define BOOT_TARGET_DEVICE_SCSI(func) func(SCSI, scsi, 0) func(SCSI, scsi, 1)
+#else
+#define BOOT_TARGET_DEVICE_SCSI(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_DEVICE_USB(func) \
+ BOOT_TARGET_DEVICE_MMC(func) \
+ BOOT_TARGET_DEVICE_SCSI(func) \
+ BOOT_TARGET_DEVICE_NVME(func) \
+
+#include <config_distro_bootcmd.h>
+#else /* CONFIG_SPL_BUILD */
+#define BOOTENV
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_addr_r=0x9fe00000\0" \
+ "kernel_addr_r=0x90000000\0" \
+ "ramdisk_addr_r=0xa0000000\0" \
+ "scriptaddr=0x88000000\0" \
+ "pxefile_addr_r=0x88100000\0" \
+ BOOTENV
+
+#endif /* __CONFIG_H */
next prev parent reply other threads:[~2021-06-04 9:45 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-04 9:43 [PATCH v5 00/13] arm64: synquacer: Add SynQuacer/DeveloperBox support Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 01/13] ata: ahci-pci: Use scsi_ops to initialize ops Masami Hiramatsu
2021-07-06 22:50 ` Tom Rini
2021-07-07 22:47 ` Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 02/13] dm: pci: Skip setting VGA bridge bits if parent device is the host bus Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 03/13] efi: Fix to use null handle to create new handle for efi_fmp_raw Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 04/13] gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 05/13] pci: synquacer: Add SynQuacer ECAM based PCIe driver Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 06/13] mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 07/13] spi: synquacer: Add HSSPI SPI controller driver for SynQuacer Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 08/13] net: synquacer: Add netsec driver Masami Hiramatsu
2021-06-12 18:32 ` Ramon Fried
2021-06-12 18:39 ` Ramon Fried
2021-06-04 9:44 ` [PATCH v5 09/13] i2c: synquacer: SNI Synquacer I2C controller Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 10/13] ARM: dts: synquacer: Add device trees for DeveloperBox Masami Hiramatsu
2021-06-04 9:45 ` Masami Hiramatsu [this message]
2021-06-04 9:45 ` [PATCH v5 12/13] doc: qemu: arm64: Fix the documentation of capsule update Masami Hiramatsu
2021-06-04 9:45 ` [PATCH v5 13/13] configs: synquacer: Enable EFI capsule update support Masami Hiramatsu
2021-06-11 7:25 ` [PATCH v5 00/13] arm64: synquacer: Add SynQuacer/DeveloperBox support Masami Hiramatsu
2021-06-11 8:05 ` Ilias Apalodimas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=162279991017.518877.5412912119801083387.stgit@localhost \
--to=masami.hiramatsu@linaro.org \
--cc=agraf@csgraf.de \
--cc=bmeng.cn@gmail.com \
--cc=ilias.apalodimas@linaro.org \
--cc=jagan@amarulasolutions.com \
--cc=jaswinder.singh@linaro.org \
--cc=jh80.chung@samsung.com \
--cc=joe.hershberger@ni.com \
--cc=masahisa.kojima@linaro.org \
--cc=peng.fan@nxp.com \
--cc=rfried.dev@gmail.com \
--cc=sjg@chromium.org \
--cc=sughosh.ganu@linaro.org \
--cc=takahiro.akashi@linaro.org \
--cc=tharvey@gateworks.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
--cc=vigneshr@ti.com \
--cc=xypron.glpk@gmx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.