From: Masami Hiramatsu <masami.hiramatsu@linaro.org>
To: Peng Fan <peng.fan@nxp.com>, Simon Glass <sjg@chromium.org>,
Tom Rini <trini@konsulko.com>,
Heinrich Schuchardt <xypron.glpk@gmx.de>,
Alexander Graf <agraf@csgraf.de>,
Jagan Teki <jagan@amarulasolutions.com>,
Vignesh R <vigneshr@ti.com>,
Joe Hershberger <joe.hershberger@ni.com>,
Ramon Fried <rfried.dev@gmail.com>,
Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>,
Jassi Brar <jaswinder.singh@linaro.org>,
Ilias Apalodimas <ilias.apalodimas@linaro.org>,
Masahisa Kojima <masahisa.kojima@linaro.org>,
Takahiro Akashi <takahiro.akashi@linaro.org>,
Tim Harvey <tharvey@gateworks.com>, Bin Meng <bmeng.cn@gmail.com>,
u-boot@lists.denx.de, Jaehoon Chung <jh80.chung@samsung.com>
Subject: [PATCH v5 05/13] pci: synquacer: Add SynQuacer ECAM based PCIe driver
Date: Fri, 4 Jun 2021 18:44:06 +0900 [thread overview]
Message-ID: <162279984570.518877.10358637170852384548.stgit@localhost> (raw)
In-Reply-To: <162279979193.518877.11119025270138617301.stgit@localhost>
Add ECAM based SynQuacer PCIe RC driver. This driver configures the
PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device
is configured by firmware (EDK2), it doesn't re-configure in the kernel.
So as same as EDK2, U-Boot needs to configure it before boot the kernel.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
---
drivers/pci/Kconfig | 12 +
drivers/pci/Makefile | 1
drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++++++++++++++++++++++++++++
3 files changed, 613 insertions(+)
create mode 100644 drivers/pci/pcie_ecam_synquacer.c
diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
index b2b7b253f8..782179eb0f 100644
--- a/drivers/pci/Kconfig
+++ b/drivers/pci/Kconfig
@@ -81,6 +81,18 @@ config PCIE_ECAM_GENERIC
Say Y here if you want to enable support for generic ECAM-based
PCIe host controllers, such as the one emulated by QEMU.
+config PCIE_ECAM_SYNQUACER
+ bool "SynQuacer ECAM-based PCI host controller support"
+ default n
+ depends on DM_PCI
+ select PCI_INIT_R
+ select PCI_REGION_MULTI_ENTRY
+ help
+ Say Y here if you want to enable support for Socionext
+ SynQuacer SoC's ECAM-based PCIe host controllers.
+ Note that this must be configured when boot because Linux driver
+ expects the PCIe RC has been configured in the bootloader.
+
config PCI_PHYTIUM
bool "Phytium PCIe support"
depends on DM_PCI
diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
index c742bb2c94..6568dc9a08 100644
--- a/drivers/pci/Makefile
+++ b/drivers/pci/Makefile
@@ -16,6 +16,7 @@ endif
obj-$(CONFIG_PCI) += pci_auto_common.o pci_common.o
obj-$(CONFIG_PCIE_ECAM_GENERIC) += pcie_ecam_generic.o
+obj-$(CONFIG_PCIE_ECAM_SYNQUACER) += pcie_ecam_synquacer.o
obj-$(CONFIG_FSL_PCI_INIT) += fsl_pci_init.o
obj-$(CONFIG_PCI_INDIRECT_BRIDGE) += pci_indirect.o
obj-$(CONFIG_PCI_GT64120) += pci_gt64120.o
diff --git a/drivers/pci/pcie_ecam_synquacer.c b/drivers/pci/pcie_ecam_synquacer.c
new file mode 100644
index 0000000000..c6e7c59f8a
--- /dev/null
+++ b/drivers/pci/pcie_ecam_synquacer.c
@@ -0,0 +1,600 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SynQuacer PCIE host driver
+ *
+ * Based on drivers/pci/pcie_ecam_generic.c
+ *
+ * Copyright (C) 2016 Imagination Technologies
+ * Copyright (C) 2021 Linaro Ltd.
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <pci.h>
+#include <log.h>
+
+#include <asm/io.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+
+/* iATU registers */
+#define IATU_VIEWPORT_OFF 0x900
+#define IATU_VIEWPORT_INBOUND BIT(31)
+#define IATU_VIEWPORT_OUTBOUND 0
+#define IATU_VIEWPORT_REGION_INDEX(idx) ((idx) & 7)
+
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0 0x904
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_MEM 0x0
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_IO 0x2
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG0 0x4
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG1 0x5
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TH BIT(12)
+
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0 0x908
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0_REGION_EN BIT(31)
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0_CFG_SHIFT_MODE BIT(28)
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0_MSG_CODE_32BIT 0xF
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0_MSG_CODE_64BIT 0xFF
+
+#define IATU_LWR_BASE_ADDR_OFF_OUTBOUND_0 0x90C
+#define IATU_UPPER_BASE_ADDR_OFF_OUTBOUND_0 0x910
+#define IATU_LIMIT_ADDR_OFF_OUTBOUND_0 0x914
+#define IATU_LWR_TARGET_ADDR_OFF_OUTBOUND_0 0x918
+#define IATU_UPPER_TARGET_ADDR_OFF_OUTBOUND_0 0x91C
+
+/* Clock and resets */
+#define CORE_CONTROL 0x000
+#define APP_LTSSM_ENABLE BIT(4)
+#define DEVICE_TYPE (BIT(3) | BIT(2) | BIT(1) | BIT(0))
+
+#define AXI_CLK_STOP 0x004
+#define DBI_ACLK_STOP BIT(8)
+#define SLV_ACLK_STOP BIT(4)
+#define MSTR_ACLK_STOP BIT(0)
+#define DBI_CSYSREQ_REG BIT(9)
+#define SLV_CSYSREQ_REG BIT(5)
+#define MSTR_CSYSREQ_REG BIT(1)
+
+#define RESET_CONTROL_1 0x00C
+#define PERST_N_O_REG BIT(5)
+#define PERST_N_I_REG BIT(4)
+#define BUTTON_RST_N_REG BIT(1)
+#define PWUP_RST_N_REG BIT(0)
+
+#define RESET_CONTROL_2 0x010
+
+#define RESET_SELECT_1 0x014
+#define SQU_RST_SEL BIT(29)
+#define PHY_RST_SEL BIT(28)
+#define PWR_RST_SEL BIT(24)
+#define STI_RST_SEL BIT(20)
+#define N_STI_RST_SEL BIT(16)
+#define CORE_RST_SEL BIT(12)
+#define PERST_SEL BIT(4)
+#define BUTTON_RST_SEL BIT(1)
+#define PWUP_RST_SEL BIT(0)
+
+#define RESET_SELECT_2 0x018
+#define DBI_ARST_SEL BIT(8)
+#define SLV_ARST_SEL BIT(4)
+#define MSTR_ARST_SEL BIT(0)
+
+#define EM_CONTROL 0x030
+#define PRE_DET_STT_REG BIT(4)
+
+#define EM_SELECT 0x034
+#define PRE_DET_STT_SEL BIT(4)
+
+#define PM_CONTROL_2 0x050
+#define SYS_AUX_PWR_DET BIT(8)
+
+#define PHY_CONFIG_COM_6 0x114
+#define PIPE_PORT_SEL GENMASK(1, 0)
+
+#define LINK_MONITOR 0x210
+#define SMLH_LINK_UP BIT(0)
+
+#define LINK_CAPABILITIES_REG 0x07C
+#define PCIE_CAP_MAX_LINK_WIDTH GENMASK(7, 4)
+#define PCIE_CAP_MAX_LINK_SPEED GENMASK(3, 0)
+
+#define LINK_CONTROL_LINK_STATUS_REG 0x080
+#define PCIE_CAP_NEGO_LINK_WIDTH GENMASK(23, 20)
+#define PCIE_CAP_LINK_SPEED GENMASK(19, 16)
+
+#define TYPE1_CLASS_CODE_REV_ID_REG 0x008
+#define BASE_CLASS_CODE 0xFF000000
+#define BASE_CLASS_CODE_VALUE 0x06
+#define SUBCLASS_CODE 0x00FF0000
+#define SUBCLASS_CODE_VALUE 0x04
+#define PROGRAM_INTERFACE 0x0000FF00
+#define PROGRAM_INTERFACE_VALUE 0x00
+
+#define GEN2_CONTROL_OFF 0x80c
+#define DIRECT_SPEED_CHANGE BIT(17)
+
+#define MISC_CONTROL_1_OFF 0x8BC
+#define DBI_RO_WR_EN BIT(0)
+
+static void or_writel(void *base, u32 offs, u32 val)
+{
+ writel(readl(base + offs) | val, base + offs);
+}
+
+static void masked_writel(void *base, u32 offs, u32 mask, u32 val)
+{
+ u32 data;
+ int shift = ffs(mask); /* Note that ffs() returns 1 for 0x1 */
+
+ if (val && shift > 1)
+ val <<= shift - 1;
+
+ if (mask != ~0)
+ data = (readl(base + offs) & ~mask) | val;
+ else
+ data = val;
+
+ writel(data, base + offs);
+}
+
+static u32 masked_readl(void *base, u32 offs, u32 mask)
+{
+ u32 data;
+ int shift = ffs(mask); /* Note that ffs() returns 1 for 0x1 */
+
+ data = readl(base + offs);
+
+ if (mask != ~0)
+ data &= mask;
+ if (shift > 1)
+ data >>= shift - 1;
+
+ return data;
+}
+
+/*
+ * Since SynQuacer's PCIe RC is expected to be initialized in the
+ * firmware (including U-Boot), devicetree doesn't have control
+ * blocks.
+ *
+ * Thus, this will initialize the PCIe RC with fixed addresses.
+ */
+
+#define SYNQUACER_PCI_SEG0_CONFIG_BASE 0x60000000
+#define SYNQUACER_PCI_SEG0_CONFIG_SIZE 0x07f00000
+#define SYNQUACER_PCI_SEG0_DBI_BASE 0x583d0000
+#define SYNQUACER_PCI_SEG0_EXS_BASE 0x58390000
+
+#define SYNQUACER_PCI_SEG1_CONFIG_BASE 0x70000000
+#define SYNQUACER_PCI_SEG1_CONFIG_SIZE 0x07f00000
+#define SYNQUACER_PCI_SEG1_DBI_BASE 0x583c0000
+#define SYNQUACER_PCI_SEG1_EXS_BASE 0x58380000
+
+#define SIZE_16KB 0x00004000
+#define SIZE_64KB 0x00010000
+#define SIZE_1MB 0x00100000
+
+#define SYNQUACER_PCI_DBI_SIZE SIZE_16KB
+#define SYNQUACER_PCI_EXS_SIZE SIZE_64KB
+
+#define NUM_SQ_PCI_RC 2
+
+static const struct synquacer_pcie_base {
+ phys_addr_t cfg_base;
+ phys_addr_t dbi_base;
+ phys_addr_t exs_base;
+} synquacer_pci_bases[NUM_SQ_PCI_RC] = {
+ {
+ .cfg_base = SYNQUACER_PCI_SEG0_CONFIG_BASE,
+ .dbi_base = SYNQUACER_PCI_SEG0_DBI_BASE,
+ .exs_base = SYNQUACER_PCI_SEG0_EXS_BASE,
+ }, {
+ .cfg_base = SYNQUACER_PCI_SEG1_CONFIG_BASE,
+ .dbi_base = SYNQUACER_PCI_SEG1_DBI_BASE,
+ .exs_base = SYNQUACER_PCI_SEG1_EXS_BASE,
+ },
+};
+
+/**
+ * struct synquacer_ecam_pcie - synquacer_ecam PCIe controller state
+ * @cfg_base: The base address of memory mapped configuration space
+ */
+struct synquacer_ecam_pcie {
+ void *cfg_base;
+ pci_size_t size;
+ void *dbi_base;
+ void *exs_base;
+ int first_busno;
+
+ struct pci_region mem;
+ struct pci_region io;
+ struct pci_region mem64;
+};
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/**
+ * pci_synquacer_ecam_conf_address() - Calculate the address of a config access
+ * @bus: Pointer to the PCI bus
+ * @bdf: Identifies the PCIe device to access
+ * @offset: The offset into the device's configuration space
+ * @paddress: Pointer to the pointer to write the calculates address to
+ *
+ * Calculates the address that should be accessed to perform a PCIe
+ * configuration space access for a given device identified by the PCIe
+ * controller device @pcie and the bus, device & function numbers in @bdf. If
+ * access to the device is not valid then the function will return an error
+ * code. Otherwise the address to access will be written to the pointer pointed
+ * to by @paddress.
+ */
+static int pci_synquacer_ecam_conf_address(const struct udevice *bus,
+ pci_dev_t bdf, uint offset,
+ void **paddress)
+{
+ struct synquacer_ecam_pcie *pcie = dev_get_priv(bus);
+ void *addr;
+
+ addr = pcie->cfg_base;
+ addr += (PCI_BUS(bdf) - pcie->first_busno) << 20;
+ addr += PCI_DEV(bdf) << 15;
+ addr += PCI_FUNC(bdf) << 12;
+ addr += offset;
+ *paddress = addr;
+
+ return 0;
+}
+
+static bool pci_synquacer_ecam_addr_valid(const struct udevice *bus,
+ pci_dev_t bdf)
+{
+ struct synquacer_ecam_pcie *pcie = dev_get_priv(bus);
+ int num_buses = DIV_ROUND_UP(pcie->size, 1 << 16);
+
+ /*
+ * The Synopsys DesignWare PCIe controller in ECAM mode will not filter
+ * type 0 config TLPs sent to devices 1 and up on its downstream port,
+ * resulting in devices appearing multiple times on bus 0 unless we
+ * filter out those accesses here.
+ */
+ if (PCI_BUS(bdf) == pcie->first_busno && PCI_DEV(bdf) > 0)
+ return false;
+
+ return (PCI_BUS(bdf) >= pcie->first_busno &&
+ PCI_BUS(bdf) < pcie->first_busno + num_buses);
+}
+
+/**
+ * pci_synquacer_ecam_read_config() - Read from configuration space
+ * @bus: Pointer to the PCI bus
+ * @bdf: Identifies the PCIe device to access
+ * @offset: The offset into the device's configuration space
+ * @valuep: A pointer at which to store the read value
+ * @size: Indicates the size of access to perform
+ *
+ * Read a value of size @size from offset @offset within the configuration
+ * space of the device identified by the bus, device & function numbers in @bdf
+ * on the PCI bus @bus.
+ */
+static int pci_synquacer_ecam_read_config(const struct udevice *bus,
+ pci_dev_t bdf, uint offset,
+ ulong *valuep, enum pci_size_t size)
+{
+ if (!pci_synquacer_ecam_addr_valid(bus, bdf)) {
+ *valuep = pci_get_ff(size);
+ return 0;
+ }
+
+ return pci_generic_mmap_read_config(bus, pci_synquacer_ecam_conf_address,
+ bdf, offset, valuep, size);
+}
+
+/**
+ * pci_synquacer_ecam_write_config() - Write to configuration space
+ * @bus: Pointer to the PCI bus
+ * @bdf: Identifies the PCIe device to access
+ * @offset: The offset into the device's configuration space
+ * @value: The value to write
+ * @size: Indicates the size of access to perform
+ *
+ * Write the value @value of size @size from offset @offset within the
+ * configuration space of the device identified by the bus, device & function
+ * numbers in @bdf on the PCI bus @bus.
+ */
+static int pci_synquacer_ecam_write_config(struct udevice *bus, pci_dev_t bdf,
+ uint offset, ulong value,
+ enum pci_size_t size)
+{
+ if (!pci_synquacer_ecam_addr_valid(bus, bdf))
+ return 0;
+
+ return pci_generic_mmap_write_config(bus, pci_synquacer_ecam_conf_address,
+ bdf, offset, value, size);
+}
+
+/**
+ * pci_synquacer_ecam_of_to_plat() - Translate from DT to device state
+ * @dev: A pointer to the device being operated on
+ *
+ * Translate relevant data from the device tree pertaining to device @dev into
+ * state that the driver will later make use of. This state is stored in the
+ * device's private data structure.
+ *
+ * Return: 0 on success, else -EINVAL
+ */
+static int pci_synquacer_ecam_of_to_plat(struct udevice *dev)
+{
+ struct synquacer_ecam_pcie *pcie = dev_get_priv(dev);
+ struct fdt_resource reg_res;
+ int i, err;
+
+ debug("%s: called for %s\n", __func__, dev->name);
+
+ err = fdt_get_resource(gd->fdt_blob, dev_of_offset(dev), "reg",
+ 0, ®_res);
+ if (err < 0) {
+ pr_err("\"reg\" resource not found\n");
+ return err;
+ }
+
+ /* Find the correct pair of the DBI/EXS base address */
+ for (i = 0; i < NUM_SQ_PCI_RC; i++) {
+ if (synquacer_pci_bases[i].cfg_base == reg_res.start)
+ break;
+ }
+ if (i == NUM_SQ_PCI_RC) {
+ pr_err("Unknown ECAM base address %lx.\n",
+ (unsigned long)reg_res.start);
+ return -ENOENT;
+ }
+ pcie->dbi_base = map_physmem(synquacer_pci_bases[i].dbi_base,
+ SYNQUACER_PCI_DBI_SIZE, MAP_NOCACHE);
+ if (!pcie->dbi_base) {
+ pr_err("Failed to map DBI for %s\n", dev->name);
+ return -ENOMEM;
+ }
+
+ pcie->exs_base = map_physmem(synquacer_pci_bases[i].exs_base,
+ SYNQUACER_PCI_EXS_SIZE, MAP_NOCACHE);
+ if (!pcie->exs_base) {
+ pr_err("Failed to map EXS for %s\n", dev->name);
+ return -ENOMEM;
+ }
+
+ pcie->size = fdt_resource_size(®_res);
+ pcie->cfg_base = map_physmem(reg_res.start, pcie->size, MAP_NOCACHE);
+ if (!pcie->cfg_base) {
+ pr_err("Failed to map config space for %s\n", dev->name);
+ return -ENOMEM;
+ }
+ debug("mappings DBI: %p EXS: %p CFG: %p\n", pcie->dbi_base, pcie->exs_base, pcie->cfg_base);
+
+ return 0;
+}
+
+static void pci_synquacer_pre_init(struct synquacer_ecam_pcie *pcie)
+{
+ void *base = pcie->exs_base;
+
+ masked_writel(base, EM_SELECT, PRE_DET_STT_SEL, 0);
+ masked_writel(base, EM_CONTROL, PRE_DET_STT_REG, 0);
+ masked_writel(base, EM_CONTROL, PRE_DET_STT_REG, 1);
+
+ /* 1: Assert all PHY / LINK resets */
+ masked_writel(base, RESET_SELECT_1, PERST_SEL, 0);
+ masked_writel(base, RESET_CONTROL_1, PERST_N_I_REG, 0);
+ masked_writel(base, RESET_CONTROL_1, PERST_N_O_REG, 0);
+
+ /* Device Reset(PERST#) is effective afrer Set device_type (RC) */
+ masked_writel(base, RESET_SELECT_1, PWUP_RST_SEL, 0);
+ masked_writel(base, RESET_CONTROL_1, PWUP_RST_N_REG, 0);
+ masked_writel(base, RESET_SELECT_1, BUTTON_RST_SEL, 0);
+ masked_writel(base, RESET_CONTROL_1, BUTTON_RST_N_REG, 0);
+ masked_writel(base, RESET_SELECT_1, PWR_RST_SEL, 1);
+ masked_writel(base, RESET_SELECT_2, MSTR_ARST_SEL, 1);
+ masked_writel(base, RESET_SELECT_2, SLV_ARST_SEL, 1);
+ masked_writel(base, RESET_SELECT_2, DBI_ARST_SEL, 1);
+ masked_writel(base, RESET_SELECT_1, CORE_RST_SEL, 1);
+ masked_writel(base, RESET_SELECT_1, STI_RST_SEL, 1);
+ masked_writel(base, RESET_SELECT_1, N_STI_RST_SEL, 1);
+ masked_writel(base, RESET_SELECT_1, SQU_RST_SEL, 1);
+ masked_writel(base, RESET_SELECT_1, PHY_RST_SEL, 1);
+
+ /* 2: Set P<n>_app_ltssm_enable='0' for reprogramming before linkup. */
+ masked_writel(base, CORE_CONTROL, APP_LTSSM_ENABLE, 0);
+
+ /* 3: Set device_type (RC) */
+ masked_writel(base, CORE_CONTROL, DEVICE_TYPE, 4);
+}
+
+static void pci_synquacer_dbi_init(void *dbi_base)
+{
+ masked_writel(dbi_base, MISC_CONTROL_1_OFF, DBI_RO_WR_EN, 1);
+ /* 4 Lanes */
+ masked_writel(dbi_base, LINK_CAPABILITIES_REG,
+ PCIE_CAP_MAX_LINK_WIDTH, 4);
+ /* Gen 2 */
+ masked_writel(dbi_base, LINK_CAPABILITIES_REG,
+ PCIE_CAP_MAX_LINK_SPEED, 2);
+
+ masked_writel(dbi_base, TYPE1_CLASS_CODE_REV_ID_REG,
+ BASE_CLASS_CODE, BASE_CLASS_CODE_VALUE);
+ masked_writel(dbi_base, TYPE1_CLASS_CODE_REV_ID_REG,
+ SUBCLASS_CODE, SUBCLASS_CODE_VALUE);
+ masked_writel(dbi_base, TYPE1_CLASS_CODE_REV_ID_REG,
+ PROGRAM_INTERFACE, PROGRAM_INTERFACE_VALUE);
+
+ masked_writel(dbi_base, MISC_CONTROL_1_OFF, DBI_RO_WR_EN, 0);
+}
+
+static void pcie_sq_prog_outbound_atu(void *dbi_base, int index,
+ u64 cpu_base, u64 pci_base, u64 size,
+ u32 type, u32 flags)
+{
+ debug("%s: %p, %d, %llx, %llx, %llx, %x, %x\n", __func__,
+ dbi_base, index, cpu_base, pci_base, size, type, flags);
+
+ writel(IATU_VIEWPORT_OUTBOUND | IATU_VIEWPORT_REGION_INDEX(index),
+ dbi_base + IATU_VIEWPORT_OFF);
+
+ writel((u32)(cpu_base & 0xffffffff),
+ dbi_base + IATU_LWR_BASE_ADDR_OFF_OUTBOUND_0);
+ writel((u32)(cpu_base >> 32),
+ dbi_base + IATU_UPPER_BASE_ADDR_OFF_OUTBOUND_0);
+ writel((u32)(cpu_base + size - 1),
+ dbi_base + IATU_LIMIT_ADDR_OFF_OUTBOUND_0);
+
+ writel((u32)(pci_base & 0xffffffff),
+ dbi_base + IATU_LWR_TARGET_ADDR_OFF_OUTBOUND_0);
+ writel((u32)(pci_base >> 32),
+ dbi_base + IATU_UPPER_TARGET_ADDR_OFF_OUTBOUND_0);
+
+ writel(type, dbi_base + IATU_REGION_CTRL_1_OFF_OUTBOUND_0);
+ writel(IATU_REGION_CTRL_2_OFF_OUTBOUND_0_REGION_EN | flags,
+ dbi_base + IATU_REGION_CTRL_2_OFF_OUTBOUND_0);
+}
+
+static void pci_synquacer_post_init(struct synquacer_ecam_pcie *pcie)
+{
+ void *base = pcie->exs_base;
+
+ /*
+ * 4: Set Bifurcation 1=disable 4=able
+ * 5: Supply Reference (It has executed)
+ * 6: Wait for 10usec (Reference Clocks is stable)
+ * 7: De assert PERST#
+ */
+ masked_writel(base, RESET_CONTROL_1, PERST_N_I_REG, 1);
+ masked_writel(base, RESET_CONTROL_1, PERST_N_O_REG, 1);
+
+ /* 8: Assert SYS_AUX_PWR_DET */
+ masked_writel(base, PM_CONTROL_2, SYS_AUX_PWR_DET, 1);
+
+ /* 9: Supply following clocks */
+ masked_writel(base, AXI_CLK_STOP, MSTR_CSYSREQ_REG, 1);
+ masked_writel(base, AXI_CLK_STOP, MSTR_ACLK_STOP, 0);
+ masked_writel(base, AXI_CLK_STOP, SLV_CSYSREQ_REG, 1);
+ masked_writel(base, AXI_CLK_STOP, SLV_ACLK_STOP, 0);
+ masked_writel(base, AXI_CLK_STOP, DBI_CSYSREQ_REG, 1);
+ masked_writel(base, AXI_CLK_STOP, DBI_ACLK_STOP, 0);
+
+ /*
+ * 10: De assert PHY reset
+ * 11: De assert LINK's PMC reset
+ */
+ masked_writel(base, RESET_CONTROL_1, PWUP_RST_N_REG, 1);
+ masked_writel(base, RESET_CONTROL_1, BUTTON_RST_N_REG, 1);
+
+ /* 12: PHY auto
+ * 13: Wrapper auto
+ * 14-17: PHY auto
+ * 18: Wrapper auto
+ * 19: Update registers through DBI AXI Slave interface
+ */
+ pci_synquacer_dbi_init(pcie->dbi_base);
+
+ or_writel(pcie->dbi_base, PCI_COMMAND,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ /* Force link speed change to Gen2 at link up */
+ or_writel(pcie->dbi_base, GEN2_CONTROL_OFF, DIRECT_SPEED_CHANGE);
+
+ /* Region 0: MMIO32 range */
+ pcie_sq_prog_outbound_atu(pcie->dbi_base, 0,
+ pcie->mem.phys_start,
+ pcie->mem.bus_start,
+ pcie->mem.size,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_MEM |
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TH,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_MSG_CODE_32BIT);
+
+ /* Region 1: Type 0 config space */
+ pcie_sq_prog_outbound_atu(pcie->dbi_base, 1,
+ (u64)pcie->cfg_base,
+ 0,
+ SIZE_64KB,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG0,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_CFG_SHIFT_MODE);
+
+ /* Region 2: Type 1 config space */
+ pcie_sq_prog_outbound_atu(pcie->dbi_base, 2,
+ (u64)pcie->cfg_base + SIZE_64KB,
+ 0,
+ (u64)pcie->io.phys_start - (u64)pcie->cfg_base - SIZE_64KB,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG1,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_CFG_SHIFT_MODE);
+
+ /* Region 3: port I/O range */
+ pcie_sq_prog_outbound_atu(pcie->dbi_base, 3,
+ pcie->io.phys_start,
+ pcie->io.bus_start,
+ pcie->io.size,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_IO,
+ 0);
+
+ /* Region 4: MMIO64 range */
+ pcie_sq_prog_outbound_atu(pcie->dbi_base, 4,
+ pcie->mem64.phys_start,
+ pcie->mem64.bus_start,
+ pcie->mem64.size,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_MEM |
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TH,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_MSG_CODE_32BIT);
+
+ /* enable link */
+ if (masked_readl(base, CORE_CONTROL, APP_LTSSM_ENABLE) == 0)
+ masked_writel(base, CORE_CONTROL, APP_LTSSM_ENABLE, 1);
+}
+
+static int pci_synquacer_ecam_probe(struct udevice *dev)
+{
+ struct synquacer_ecam_pcie *pcie = dev_get_priv(dev);
+ struct udevice *ctlr = pci_get_controller(dev);
+ struct pci_controller *hose = dev_get_uclass_priv(ctlr);
+
+ debug("Probe synquacer pcie for bus %d\n", dev_seq(dev));
+ pcie->first_busno = dev_seq(dev);
+
+ /* Store the IO and MEM windows settings for configuring ATU */
+ pcie->io.phys_start = hose->regions[0].phys_start; /* IO base */
+ pcie->io.bus_start = hose->regions[0].bus_start; /* IO_bus_addr */
+ pcie->io.size = hose->regions[0].size; /* IO size */
+
+ pcie->mem.phys_start = hose->regions[1].phys_start; /* MEM base */
+ pcie->mem.bus_start = hose->regions[1].bus_start; /* MEM_bus_addr */
+ pcie->mem.size = hose->regions[1].size; /* MEM size */
+
+ pcie->mem64.phys_start = hose->regions[2].phys_start; /* MEM64 base */
+ pcie->mem64.bus_start = hose->regions[2].bus_start; /* MEM64_bus_addr */
+ pcie->mem64.size = hose->regions[2].size; /* MEM64 size */
+
+ pci_synquacer_pre_init(pcie);
+
+ mdelay(150);
+
+ pci_synquacer_post_init(pcie);
+
+ /* It takes a while to stabilize the PCIe bus for scanning */
+ mdelay(100);
+
+ return 0;
+}
+
+static const struct dm_pci_ops pci_synquacer_ecam_ops = {
+ .read_config = pci_synquacer_ecam_read_config,
+ .write_config = pci_synquacer_ecam_write_config,
+};
+
+static const struct udevice_id pci_synquacer_ecam_ids[] = {
+ { .compatible = "socionext,synquacer-pcie-ecam" },
+ { }
+};
+
+U_BOOT_DRIVER(pci_synquacer_ecam) = {
+ .name = "pci_synquacer_ecam",
+ .id = UCLASS_PCI,
+ .of_match = pci_synquacer_ecam_ids,
+ .ops = &pci_synquacer_ecam_ops,
+ .probe = pci_synquacer_ecam_probe,
+ .of_to_plat = pci_synquacer_ecam_of_to_plat,
+ .priv_auto = sizeof(struct synquacer_ecam_pcie),
+};
next prev parent reply other threads:[~2021-06-04 9:44 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-04 9:43 [PATCH v5 00/13] arm64: synquacer: Add SynQuacer/DeveloperBox support Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 01/13] ata: ahci-pci: Use scsi_ops to initialize ops Masami Hiramatsu
2021-07-06 22:50 ` Tom Rini
2021-07-07 22:47 ` Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 02/13] dm: pci: Skip setting VGA bridge bits if parent device is the host bus Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 03/13] efi: Fix to use null handle to create new handle for efi_fmp_raw Masami Hiramatsu
2021-06-04 9:43 ` [PATCH v5 04/13] gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs Masami Hiramatsu
2021-06-04 9:44 ` Masami Hiramatsu [this message]
2021-06-04 9:44 ` [PATCH v5 06/13] mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 07/13] spi: synquacer: Add HSSPI SPI controller driver for SynQuacer Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 08/13] net: synquacer: Add netsec driver Masami Hiramatsu
2021-06-12 18:32 ` Ramon Fried
2021-06-12 18:39 ` Ramon Fried
2021-06-04 9:44 ` [PATCH v5 09/13] i2c: synquacer: SNI Synquacer I2C controller Masami Hiramatsu
2021-06-04 9:44 ` [PATCH v5 10/13] ARM: dts: synquacer: Add device trees for DeveloperBox Masami Hiramatsu
2021-06-04 9:45 ` [PATCH v5 11/13] board: synquacer: Add DeveloperBox 96boards EE support Masami Hiramatsu
2021-06-04 9:45 ` [PATCH v5 12/13] doc: qemu: arm64: Fix the documentation of capsule update Masami Hiramatsu
2021-06-04 9:45 ` [PATCH v5 13/13] configs: synquacer: Enable EFI capsule update support Masami Hiramatsu
2021-06-11 7:25 ` [PATCH v5 00/13] arm64: synquacer: Add SynQuacer/DeveloperBox support Masami Hiramatsu
2021-06-11 8:05 ` Ilias Apalodimas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=162279984570.518877.10358637170852384548.stgit@localhost \
--to=masami.hiramatsu@linaro.org \
--cc=agraf@csgraf.de \
--cc=bmeng.cn@gmail.com \
--cc=ilias.apalodimas@linaro.org \
--cc=jagan@amarulasolutions.com \
--cc=jaswinder.singh@linaro.org \
--cc=jh80.chung@samsung.com \
--cc=joe.hershberger@ni.com \
--cc=masahisa.kojima@linaro.org \
--cc=peng.fan@nxp.com \
--cc=rfried.dev@gmail.com \
--cc=sjg@chromium.org \
--cc=sughosh.ganu@linaro.org \
--cc=takahiro.akashi@linaro.org \
--cc=tharvey@gateworks.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
--cc=vigneshr@ti.com \
--cc=xypron.glpk@gmx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.