* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
[not found] <ab516cfd-24e8-4761-93a3-49f96a4e6b8f@gmail.com>
@ 2024-01-29 22:19 ` Heiner Kallweit
0 siblings, 0 replies; 10+ messages in thread
From: Heiner Kallweit @ 2024-01-29 22:19 UTC (permalink / raw)
To: Joe Salmeri; +Cc: netdev@vger.kernel.org
On 29.01.2024 19:31, Joe Salmeri wrote:
> Hi,
>
> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>
> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>
> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>
> There does not seem to be a driver for the Realtek 8126.
>
> Here is the device info from "lspci | grep -i net"
>
> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>
> So it is detects the 8126 just fine it just doesn't have a driver for it.
>
> I checked realtek.com and found
>
> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>
> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
> resulting module file.
>
> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>
> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
> is what is used to support the older Realtek 8125 device.
>
> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>
> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>
> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>
> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>
> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>
> The details of the openSUSE bug report on the issue can be found here:
>
> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>
> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>
Thanks for the report. Actually it's not a bug report but a feature request.
Realtek provides no information about new chip versions and no data sheets, therefore the only
source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
handling, therefore the first steps you described go in the right direction, but are by far not
sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
Disclaimer:
r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
Typically the firmware files tune PHY parameters to deal with compatibility issues.
In addition r8125 includes a lot of PHY tuning for RTL8126A.
Depending on cabling, link partner etc. the patch may work for you, or you may experience
link instability or worst case no link at all.
Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
In this case the driver will complain with the following message and I'd need the PHY ID.
"no dedicated PHY driver found for PHY ID xxx"
> Please let me know if you need any further details.
>
> Thank you!
>
---
drivers/net/ethernet/realtek/r8169.h | 1 +
drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
.../net/ethernet/realtek/r8169_phy_config.c | 1 +
3 files changed, 77 insertions(+), 16 deletions(-)
diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
index 81567fcf3..c921456ed 100644
--- a/drivers/net/ethernet/realtek/r8169.h
+++ b/drivers/net/ethernet/realtek/r8169.h
@@ -68,6 +68,7 @@ enum mac_version {
/* support for RTL_GIGA_MAC_VER_60 has been removed */
RTL_GIGA_MAC_VER_61,
RTL_GIGA_MAC_VER_63,
+ RTL_GIGA_MAC_VER_65,
RTL_GIGA_MAC_NONE
};
diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
index e0abdbcfa..ebf7a3b13 100644
--- a/drivers/net/ethernet/realtek/r8169_main.c
+++ b/drivers/net/ethernet/realtek/r8169_main.c
@@ -55,6 +55,7 @@
#define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
#define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
#define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
+#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
#define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
#define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
@@ -136,6 +137,7 @@ static const struct {
[RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
/* reserve 62 for CFG_METHOD_4 in the vendor driver */
[RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
+ [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
};
static const struct pci_device_id rtl8169_pci_tbl[] = {
@@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
{ PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
{ 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
{ PCI_VDEVICE(REALTEK, 0x8125) },
+ { PCI_VDEVICE(REALTEK, 0x8126) },
{ PCI_VDEVICE(REALTEK, 0x3000) },
{}
};
@@ -327,8 +330,12 @@ enum rtl8168_registers {
};
enum rtl8125_registers {
+ INT_CFG0_8125 = 0x34,
+#define INT_CFG0_ENABLE_8125 BIT(0)
+#define INT_CFG0_CLKREQEN BIT(3)
IntrMask_8125 = 0x38,
IntrStatus_8125 = 0x3c,
+ INT_CFG1_8125 = 0x7a,
TxPoll_8125 = 0x90,
MAC0_BKP = 0x19e0,
EEE_TXIDLE_TIMER_8125 = 0x6048,
@@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
case RTL_GIGA_MAC_VER_31:
r8168dp_2_mdio_write(tp, location, val);
break;
- case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
r8168g_mdio_write(tp, location, val);
break;
default:
@@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
case RTL_GIGA_MAC_VER_28:
case RTL_GIGA_MAC_VER_31:
return r8168dp_2_mdio_read(tp, location);
- case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
return r8168g_mdio_read(tp, location);
default:
return r8169_mdio_read(tp, location);
@@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
break;
case RTL_GIGA_MAC_VER_34:
case RTL_GIGA_MAC_VER_37:
- case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
if (wolopts)
rtl_mod_config2(tp, 0, PME_SIGNAL);
else
@@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
u16 val;
enum mac_version ver;
} mac_info[] = {
+ /* 8126A family. */
+ { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
+
/* 8125B family. */
{ 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
@@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
break;
case RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_65:
RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
RX_PAUSE_SLOT_ON);
break;
@@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
rtl_eri_set_bits(tp, 0xd4, 0x0c00);
break;
- case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
break;
default:
@@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
break;
- case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
break;
default:
@@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
{
+ u8 val8;
+
if (tp->mac_version < RTL_GIGA_MAC_VER_32)
return;
@@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
return;
rtl_mod_config5(tp, 0, ASPM_en);
- rtl_mod_config2(tp, 0, ClkReqEn);
+ switch (tp->mac_version) {
+ case RTL_GIGA_MAC_VER_65:
+ val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
+ RTL_W8(tp, INT_CFG0_8125, val8);
+ break;
+ default:
+ rtl_mod_config2(tp, 0, ClkReqEn);
+ break;
+ }
switch (tp->mac_version) {
case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
- case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
/* reset ephy tx/rx disable timer */
r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
/* chip can trigger L1.2 */
@@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
} else {
switch (tp->mac_version) {
case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
- case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
break;
default:
break;
}
- rtl_mod_config2(tp, ClkReqEn, 0);
+ switch (tp->mac_version) {
+ case RTL_GIGA_MAC_VER_65:
+ val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
+ RTL_W8(tp, INT_CFG0_8125, val8);
+ break;
+ default:
+ rtl_mod_config2(tp, ClkReqEn, 0);
+ break;
+ }
rtl_mod_config5(tp, ASPM_en, 0);
}
}
@@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
/* disable new tx descriptor format */
r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
- if (tp->mac_version == RTL_GIGA_MAC_VER_63)
+ if (tp->mac_version == RTL_GIGA_MAC_VER_65)
+ RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
+
+ if (tp->mac_version == RTL_GIGA_MAC_VER_65)
+ r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
+ else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
else
- r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
+ r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
if (tp->mac_version == RTL_GIGA_MAC_VER_63)
r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
@@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
+ if (tp->mac_version == RTL_GIGA_MAC_VER_65)
+ r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
+ else
+ r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
@@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
- if (tp->mac_version == RTL_GIGA_MAC_VER_63)
- rtl8125b_config_eee_mac(tp);
- else
+ if (tp->mac_version == RTL_GIGA_MAC_VER_61)
rtl8125a_config_eee_mac(tp);
+ else
+ rtl8125b_config_eee_mac(tp);
rtl_disable_rxdvgate(tp);
}
@@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
rtl_hw_start_8125_common(tp);
}
+static void rtl_hw_start_8126a(struct rtl8169_private *tp)
+{
+ rtl_set_def_aspm_entry_latency(tp);
+ rtl_hw_start_8125_common(tp);
+}
+
static void rtl_hw_config(struct rtl8169_private *tp)
{
static const rtl_generic_fct hw_configs[] = {
@@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
[RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
[RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
[RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
+ [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
};
if (hw_configs[tp->mac_version])
@@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
{
int i;
+ RTL_W8(tp, INT_CFG0_8125, 0x00);
+
/* disable interrupt coalescing */
- for (i = 0xa00; i < 0xb00; i += 4)
- RTL_W32(tp, i, 0);
+ switch (tp->mac_version) {
+ case RTL_GIGA_MAC_VER_61:
+ for (i = 0xa00; i < 0xb00; i += 4)
+ RTL_W32(tp, i, 0);
+ break;
+ case RTL_GIGA_MAC_VER_63:
+ case RTL_GIGA_MAC_VER_65:
+ for (i = 0xa00; i < 0xa80; i += 4)
+ RTL_W32(tp, i, 0);
+ RTL_W16(tp, INT_CFG1_8125, 0x0000);
+ break;
+ default:
+ break;
+ }
rtl_hw_config(tp);
}
diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
index b50f16786..badf78f81 100644
--- a/drivers/net/ethernet/realtek/r8169_phy_config.c
+++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
@@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
[RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
[RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
[RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
+ [RTL_GIGA_MAC_VER_65] = NULL,
};
if (phy_configs[ver])
--
2.43.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
[not found] <edabbc1f-5440-4170-83a4-f436a6d04f76@gmail.com>
@ 2024-01-30 16:34 ` Joe Salmeri
2024-01-30 19:59 ` Heiner Kallweit
0 siblings, 1 reply; 10+ messages in thread
From: Joe Salmeri @ 2024-01-30 16:34 UTC (permalink / raw)
To: Heiner Kallweit, netdev@vger.kernel.org
On 1/29/24 17:19, Heiner Kallweit wrote:
> On 29.01.2024 19:31, Joe Salmeri wrote:
>> Hi,
>>
>> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>>
>> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>>
>> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>>
>> There does not seem to be a driver for the Realtek 8126.
>>
>> Here is the device info from "lspci | grep -i net"
>>
>> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
>> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>>
>> So it is detects the 8126 just fine it just doesn't have a driver for it.
>>
>> I checked realtek.com and found
>>
>> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>>
>> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
>> resulting module file.
>>
>> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>>
>> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
>> is what is used to support the older Realtek 8125 device.
>>
>> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
>> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>>
>> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>>
>> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>>
>> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>>
>> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
>> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>>
>> The details of the openSUSE bug report on the issue can be found here:
>>
>> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>>
>> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>>
> Thanks for the report. Actually it's not a bug report but a feature request.
> Realtek provides no information about new chip versions and no data sheets, therefore the only
> source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
> handling, therefore the first steps you described go in the right direction, but are by far not
> sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
>
> Disclaimer:
> r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
> Typically the firmware files tune PHY parameters to deal with compatibility issues.
> In addition r8125 includes a lot of PHY tuning for RTL8126A.
> Depending on cabling, link partner etc. the patch may work for you, or you may experience
> link instability or worst case no link at all.
>
> Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
> In this case the driver will complain with the following message and I'd need the PHY ID.
> "no dedicated PHY driver found for PHY ID xxx"
Thanks very much for your quick response.
I forward your patch to the openSUSE people I have been working and they
prepared a new test kernel 6.7.2 with the patches for for me to test.
I just installed the test kernel provided with the patches but just as
you expected it complains about no dedicated PHY driver found.
Here is the dmesg | grep 8169 output with the information you requested
[ 3.176753] r8169 0000:05:00.0: enabling device (0000 -> 0003)
[ 3.184887] r8169 0000:05:00.0: no dedicated PHY driver found for PHY
ID 0x001cc862, maybe realtek.ko needs to be added to initramfs?
[ 3.184912] r8169: probe of 0000:05:00.0 failed with error -49
Thank you for your efforts.
Please let me know if you need any further details.
> ---
> drivers/net/ethernet/realtek/r8169.h | 1 +
> drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
> .../net/ethernet/realtek/r8169_phy_config.c | 1 +
> 3 files changed, 77 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
> index 81567fcf3..c921456ed 100644
> --- a/drivers/net/ethernet/realtek/r8169.h
> +++ b/drivers/net/ethernet/realtek/r8169.h
> @@ -68,6 +68,7 @@ enum mac_version {
> /* support for RTL_GIGA_MAC_VER_60 has been removed */
> RTL_GIGA_MAC_VER_61,
> RTL_GIGA_MAC_VER_63,
> + RTL_GIGA_MAC_VER_65,
> RTL_GIGA_MAC_NONE
> };
>
> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> index e0abdbcfa..ebf7a3b13 100644
> --- a/drivers/net/ethernet/realtek/r8169_main.c
> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> @@ -55,6 +55,7 @@
> #define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
> #define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
> #define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
> +#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
>
> #define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
> #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
> @@ -136,6 +137,7 @@ static const struct {
> [RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
> /* reserve 62 for CFG_METHOD_4 in the vendor driver */
> [RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
> + [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
> };
>
> static const struct pci_device_id rtl8169_pci_tbl[] = {
> @@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
> { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
> { 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
> { PCI_VDEVICE(REALTEK, 0x8125) },
> + { PCI_VDEVICE(REALTEK, 0x8126) },
> { PCI_VDEVICE(REALTEK, 0x3000) },
> {}
> };
> @@ -327,8 +330,12 @@ enum rtl8168_registers {
> };
>
> enum rtl8125_registers {
> + INT_CFG0_8125 = 0x34,
> +#define INT_CFG0_ENABLE_8125 BIT(0)
> +#define INT_CFG0_CLKREQEN BIT(3)
> IntrMask_8125 = 0x38,
> IntrStatus_8125 = 0x3c,
> + INT_CFG1_8125 = 0x7a,
> TxPoll_8125 = 0x90,
> MAC0_BKP = 0x19e0,
> EEE_TXIDLE_TIMER_8125 = 0x6048,
> @@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
> case RTL_GIGA_MAC_VER_31:
> r8168dp_2_mdio_write(tp, location, val);
> break;
> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
> r8168g_mdio_write(tp, location, val);
> break;
> default:
> @@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
> case RTL_GIGA_MAC_VER_28:
> case RTL_GIGA_MAC_VER_31:
> return r8168dp_2_mdio_read(tp, location);
> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
> return r8168g_mdio_read(tp, location);
> default:
> return r8169_mdio_read(tp, location);
> @@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
> break;
> case RTL_GIGA_MAC_VER_34:
> case RTL_GIGA_MAC_VER_37:
> - case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
> if (wolopts)
> rtl_mod_config2(tp, 0, PME_SIGNAL);
> else
> @@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
> u16 val;
> enum mac_version ver;
> } mac_info[] = {
> + /* 8126A family. */
> + { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
> +
> /* 8125B family. */
> { 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
>
> @@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
> break;
> case RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_65:
> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
> RX_PAUSE_SLOT_ON);
> break;
> @@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
> case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
> rtl_eri_set_bits(tp, 0xd4, 0x0c00);
> break;
> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
> r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
> break;
> default:
> @@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
> case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
> rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
> break;
> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
> r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
> break;
> default:
> @@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>
> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
> {
> + u8 val8;
> +
> if (tp->mac_version < RTL_GIGA_MAC_VER_32)
> return;
>
> @@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
> return;
>
> rtl_mod_config5(tp, 0, ASPM_en);
> - rtl_mod_config2(tp, 0, ClkReqEn);
> + switch (tp->mac_version) {
> + case RTL_GIGA_MAC_VER_65:
> + val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
> + RTL_W8(tp, INT_CFG0_8125, val8);
> + break;
> + default:
> + rtl_mod_config2(tp, 0, ClkReqEn);
> + break;
> + }
>
> switch (tp->mac_version) {
> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
> /* reset ephy tx/rx disable timer */
> r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
> /* chip can trigger L1.2 */
> @@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
> } else {
> switch (tp->mac_version) {
> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
> r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
> break;
> default:
> break;
> }
>
> - rtl_mod_config2(tp, ClkReqEn, 0);
> + switch (tp->mac_version) {
> + case RTL_GIGA_MAC_VER_65:
> + val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
> + RTL_W8(tp, INT_CFG0_8125, val8);
> + break;
> + default:
> + rtl_mod_config2(tp, ClkReqEn, 0);
> + break;
> + }
> rtl_mod_config5(tp, ASPM_en, 0);
> }
> }
> @@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
> /* disable new tx descriptor format */
> r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
>
> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
> + RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
> +
> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
> + else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
> r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
> else
> - r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
>
> if (tp->mac_version == RTL_GIGA_MAC_VER_63)
> r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
> @@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
> r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
> r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
> r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
> + else
> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
> r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
> r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
> r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
> @@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>
> rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
>
> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
> - rtl8125b_config_eee_mac(tp);
> - else
> + if (tp->mac_version == RTL_GIGA_MAC_VER_61)
> rtl8125a_config_eee_mac(tp);
> + else
> + rtl8125b_config_eee_mac(tp);
>
> rtl_disable_rxdvgate(tp);
> }
> @@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
> rtl_hw_start_8125_common(tp);
> }
>
> +static void rtl_hw_start_8126a(struct rtl8169_private *tp)
> +{
> + rtl_set_def_aspm_entry_latency(tp);
> + rtl_hw_start_8125_common(tp);
> +}
> +
> static void rtl_hw_config(struct rtl8169_private *tp)
> {
> static const rtl_generic_fct hw_configs[] = {
> @@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
> [RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
> [RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
> [RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
> + [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
> };
>
> if (hw_configs[tp->mac_version])
> @@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
> {
> int i;
>
> + RTL_W8(tp, INT_CFG0_8125, 0x00);
> +
> /* disable interrupt coalescing */
> - for (i = 0xa00; i < 0xb00; i += 4)
> - RTL_W32(tp, i, 0);
> + switch (tp->mac_version) {
> + case RTL_GIGA_MAC_VER_61:
> + for (i = 0xa00; i < 0xb00; i += 4)
> + RTL_W32(tp, i, 0);
> + break;
> + case RTL_GIGA_MAC_VER_63:
> + case RTL_GIGA_MAC_VER_65:
> + for (i = 0xa00; i < 0xa80; i += 4)
> + RTL_W32(tp, i, 0);
> + RTL_W16(tp, INT_CFG1_8125, 0x0000);
> + break;
> + default:
> + break;
> + }
>
> rtl_hw_config(tp);
> }
> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
> index b50f16786..badf78f81 100644
> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
> @@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
> [RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
> [RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
> [RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
> + [RTL_GIGA_MAC_VER_65] = NULL,
> };
>
> if (phy_configs[ver])
--
Regards,
Joe
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-01-30 16:34 ` Joe Salmeri
@ 2024-01-30 19:59 ` Heiner Kallweit
2024-01-31 16:14 ` Joe Salmeri
0 siblings, 1 reply; 10+ messages in thread
From: Heiner Kallweit @ 2024-01-30 19:59 UTC (permalink / raw)
To: Joe Salmeri, netdev@vger.kernel.org
On 30.01.2024 17:34, Joe Salmeri wrote:
> On 1/29/24 17:19, Heiner Kallweit wrote:
>> On 29.01.2024 19:31, Joe Salmeri wrote:
>>> Hi,
>>>
>>> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>>>
>>> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>>>
>>> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>>>
>>> There does not seem to be a driver for the Realtek 8126.
>>>
>>> Here is the device info from "lspci | grep -i net"
>>>
>>> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
>>> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>>>
>>> So it is detects the 8126 just fine it just doesn't have a driver for it.
>>>
>>> I checked realtek.com and found
>>>
>>> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>>>
>>> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
>>> resulting module file.
>>>
>>> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>>>
>>> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
>>> is what is used to support the older Realtek 8125 device.
>>>
>>> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
>>> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>>>
>>> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>>>
>>> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>>>
>>> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>>>
>>> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
>>> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>>>
>>> The details of the openSUSE bug report on the issue can be found here:
>>>
>>> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>>>
>>> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>>>
>> Thanks for the report. Actually it's not a bug report but a feature request.
>> Realtek provides no information about new chip versions and no data sheets, therefore the only
>> source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
>> handling, therefore the first steps you described go in the right direction, but are by far not
>> sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
>>
>> Disclaimer:
>> r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
>> Typically the firmware files tune PHY parameters to deal with compatibility issues.
>> In addition r8125 includes a lot of PHY tuning for RTL8126A.
>> Depending on cabling, link partner etc. the patch may work for you, or you may experience
>> link instability or worst case no link at all.
>>
>> Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
>> In this case the driver will complain with the following message and I'd need the PHY ID.
>> "no dedicated PHY driver found for PHY ID xxx"
>
> Thanks very much for your quick response.
>
> I forward your patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with the patches for for me to test.
>
> I just installed the test kernel provided with the patches but just as you expected it complains about no dedicated PHY driver found.
>
> Here is the dmesg | grep 8169 output with the information you requested
>
> [ 3.176753] r8169 0000:05:00.0: enabling device (0000 -> 0003)
> [ 3.184887] r8169 0000:05:00.0: no dedicated PHY driver found for PHY ID 0x001cc862, maybe realtek.ko needs to be added to initramfs?
> [ 3.184912] r8169: probe of 0000:05:00.0 failed with error -49
>
> Thank you for your efforts.
>
> Please let me know if you need any further details.
>
>> ---
>> drivers/net/ethernet/realtek/r8169.h | 1 +
>> drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
>> .../net/ethernet/realtek/r8169_phy_config.c | 1 +
>> 3 files changed, 77 insertions(+), 16 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
>> index 81567fcf3..c921456ed 100644
>> --- a/drivers/net/ethernet/realtek/r8169.h
>> +++ b/drivers/net/ethernet/realtek/r8169.h
>> @@ -68,6 +68,7 @@ enum mac_version {
>> /* support for RTL_GIGA_MAC_VER_60 has been removed */
>> RTL_GIGA_MAC_VER_61,
>> RTL_GIGA_MAC_VER_63,
>> + RTL_GIGA_MAC_VER_65,
>> RTL_GIGA_MAC_NONE
>> };
>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>> index e0abdbcfa..ebf7a3b13 100644
>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>> @@ -55,6 +55,7 @@
>> #define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
>> #define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
>> #define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
>> +#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
>> #define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
>> #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
>> @@ -136,6 +137,7 @@ static const struct {
>> [RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
>> /* reserve 62 for CFG_METHOD_4 in the vendor driver */
>> [RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
>> + [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
>> };
>> static const struct pci_device_id rtl8169_pci_tbl[] = {
>> @@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
>> { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
>> { 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
>> { PCI_VDEVICE(REALTEK, 0x8125) },
>> + { PCI_VDEVICE(REALTEK, 0x8126) },
>> { PCI_VDEVICE(REALTEK, 0x3000) },
>> {}
>> };
>> @@ -327,8 +330,12 @@ enum rtl8168_registers {
>> };
>> enum rtl8125_registers {
>> + INT_CFG0_8125 = 0x34,
>> +#define INT_CFG0_ENABLE_8125 BIT(0)
>> +#define INT_CFG0_CLKREQEN BIT(3)
>> IntrMask_8125 = 0x38,
>> IntrStatus_8125 = 0x3c,
>> + INT_CFG1_8125 = 0x7a,
>> TxPoll_8125 = 0x90,
>> MAC0_BKP = 0x19e0,
>> EEE_TXIDLE_TIMER_8125 = 0x6048,
>> @@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
>> case RTL_GIGA_MAC_VER_31:
>> r8168dp_2_mdio_write(tp, location, val);
>> break;
>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>> r8168g_mdio_write(tp, location, val);
>> break;
>> default:
>> @@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
>> case RTL_GIGA_MAC_VER_28:
>> case RTL_GIGA_MAC_VER_31:
>> return r8168dp_2_mdio_read(tp, location);
>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>> return r8168g_mdio_read(tp, location);
>> default:
>> return r8169_mdio_read(tp, location);
>> @@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
>> break;
>> case RTL_GIGA_MAC_VER_34:
>> case RTL_GIGA_MAC_VER_37:
>> - case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
>> if (wolopts)
>> rtl_mod_config2(tp, 0, PME_SIGNAL);
>> else
>> @@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
>> u16 val;
>> enum mac_version ver;
>> } mac_info[] = {
>> + /* 8126A family. */
>> + { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
>> +
>> /* 8125B family. */
>> { 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
>> @@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
>> break;
>> case RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_65:
>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
>> RX_PAUSE_SLOT_ON);
>> break;
>> @@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
>> case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
>> rtl_eri_set_bits(tp, 0xd4, 0x0c00);
>> break;
>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>> r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
>> break;
>> default:
>> @@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>> case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
>> rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
>> break;
>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>> r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
>> break;
>> default:
>> @@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>> {
>> + u8 val8;
>> +
>> if (tp->mac_version < RTL_GIGA_MAC_VER_32)
>> return;
>> @@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>> return;
>> rtl_mod_config5(tp, 0, ASPM_en);
>> - rtl_mod_config2(tp, 0, ClkReqEn);
>> + switch (tp->mac_version) {
>> + case RTL_GIGA_MAC_VER_65:
>> + val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
>> + RTL_W8(tp, INT_CFG0_8125, val8);
>> + break;
>> + default:
>> + rtl_mod_config2(tp, 0, ClkReqEn);
>> + break;
>> + }
>> switch (tp->mac_version) {
>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>> /* reset ephy tx/rx disable timer */
>> r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
>> /* chip can trigger L1.2 */
>> @@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>> } else {
>> switch (tp->mac_version) {
>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>> r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
>> break;
>> default:
>> break;
>> }
>> - rtl_mod_config2(tp, ClkReqEn, 0);
>> + switch (tp->mac_version) {
>> + case RTL_GIGA_MAC_VER_65:
>> + val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
>> + RTL_W8(tp, INT_CFG0_8125, val8);
>> + break;
>> + default:
>> + rtl_mod_config2(tp, ClkReqEn, 0);
>> + break;
>> + }
>> rtl_mod_config5(tp, ASPM_en, 0);
>> }
>> }
>> @@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>> /* disable new tx descriptor format */
>> r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>> + RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
>> +
>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>> + else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>> r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
>> else
>> - r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
>> if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>> r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
>> @@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>> r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
>> r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
>> r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
>> + else
>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
>> r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
>> r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
>> r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
>> @@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>> rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>> - rtl8125b_config_eee_mac(tp);
>> - else
>> + if (tp->mac_version == RTL_GIGA_MAC_VER_61)
>> rtl8125a_config_eee_mac(tp);
>> + else
>> + rtl8125b_config_eee_mac(tp);
>> rtl_disable_rxdvgate(tp);
>> }
>> @@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
>> rtl_hw_start_8125_common(tp);
>> }
>> +static void rtl_hw_start_8126a(struct rtl8169_private *tp)
>> +{
>> + rtl_set_def_aspm_entry_latency(tp);
>> + rtl_hw_start_8125_common(tp);
>> +}
>> +
>> static void rtl_hw_config(struct rtl8169_private *tp)
>> {
>> static const rtl_generic_fct hw_configs[] = {
>> @@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
>> [RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
>> [RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
>> [RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
>> + [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
>> };
>> if (hw_configs[tp->mac_version])
>> @@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
>> {
>> int i;
>> + RTL_W8(tp, INT_CFG0_8125, 0x00);
>> +
>> /* disable interrupt coalescing */
>> - for (i = 0xa00; i < 0xb00; i += 4)
>> - RTL_W32(tp, i, 0);
>> + switch (tp->mac_version) {
>> + case RTL_GIGA_MAC_VER_61:
>> + for (i = 0xa00; i < 0xb00; i += 4)
>> + RTL_W32(tp, i, 0);
>> + break;
>> + case RTL_GIGA_MAC_VER_63:
>> + case RTL_GIGA_MAC_VER_65:
>> + for (i = 0xa00; i < 0xa80; i += 4)
>> + RTL_W32(tp, i, 0);
>> + RTL_W16(tp, INT_CFG1_8125, 0x0000);
>> + break;
>> + default:
>> + break;
>> + }
>> rtl_hw_config(tp);
>> }
>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>> index b50f16786..badf78f81 100644
>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>> @@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
>> [RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
>> [RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
>> [RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
>> + [RTL_GIGA_MAC_VER_65] = NULL,
>> };
>> if (phy_configs[ver])
>
>
The followoing adds support for the integrated PHY.
Please apply it on-top and re-test.
---
drivers/net/phy/realtek.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
index 894172a3e..132784321 100644
--- a/drivers/net/phy/realtek.c
+++ b/drivers/net/phy/realtek.c
@@ -1047,6 +1047,16 @@ static struct phy_driver realtek_drvs[] = {
.resume = rtlgen_resume,
.read_page = rtl821x_read_page,
.write_page = rtl821x_write_page,
+ }, {
+ PHY_ID_MATCH_EXACT(0x001cc862),
+ .name = "RTL8251B 5Gbps PHY",
+ .get_features = rtl822x_get_features,
+ .config_aneg = rtl822x_config_aneg,
+ .read_status = rtl822x_read_status,
+ .suspend = genphy_suspend,
+ .resume = rtlgen_resume,
+ .read_page = rtl821x_read_page,
+ .write_page = rtl821x_write_page,
}, {
PHY_ID_MATCH_EXACT(0x001cc961),
.name = "RTL8366RB Gigabit Ethernet",
--
2.43.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-01-30 19:59 ` Heiner Kallweit
@ 2024-01-31 16:14 ` Joe Salmeri
2024-01-31 20:40 ` Heiner Kallweit
0 siblings, 1 reply; 10+ messages in thread
From: Joe Salmeri @ 2024-01-31 16:14 UTC (permalink / raw)
To: Heiner Kallweit, netdev@vger.kernel.org, tiwai
On 1/30/24 14:59, Heiner Kallweit wrote:
> On 30.01.2024 17:34, Joe Salmeri wrote:
>> On 1/29/24 17:19, Heiner Kallweit wrote:
>>> On 29.01.2024 19:31, Joe Salmeri wrote:
>>>> Hi,
>>>>
>>>> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>>>>
>>>> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>>>>
>>>> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>>>>
>>>> There does not seem to be a driver for the Realtek 8126.
>>>>
>>>> Here is the device info from "lspci | grep -i net"
>>>>
>>>> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
>>>> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>>>>
>>>> So it is detects the 8126 just fine it just doesn't have a driver for it.
>>>>
>>>> I checked realtek.com and found
>>>>
>>>> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>>>>
>>>> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
>>>> resulting module file.
>>>>
>>>> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>>>>
>>>> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
>>>> is what is used to support the older Realtek 8125 device.
>>>>
>>>> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
>>>> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>>>>
>>>> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>>>>
>>>> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>>>>
>>>> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>>> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>>>>
>>>> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
>>>> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>>>>
>>>> The details of the openSUSE bug report on the issue can be found here:
>>>>
>>>> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>>>>
>>>> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>>>>
>>> Thanks for the report. Actually it's not a bug report but a feature request.
>>> Realtek provides no information about new chip versions and no data sheets, therefore the only
>>> source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
>>> handling, therefore the first steps you described go in the right direction, but are by far not
>>> sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
>>>
>>> Disclaimer:
>>> r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
>>> Typically the firmware files tune PHY parameters to deal with compatibility issues.
>>> In addition r8125 includes a lot of PHY tuning for RTL8126A.
>>> Depending on cabling, link partner etc. the patch may work for you, or you may experience
>>> link instability or worst case no link at all.
>>>
>>> Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
>>> In this case the driver will complain with the following message and I'd need the PHY ID.
>>> "no dedicated PHY driver found for PHY ID xxx"
>> Thanks very much for your quick response.
>>
>> I forward your patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with the patches for for me to test.
>>
>> I just installed the test kernel provided with the patches but just as you expected it complains about no dedicated PHY driver found.
>>
>> Here is the dmesg | grep 8169 output with the information you requested
>>
>> [ 3.176753] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>> [ 3.184887] r8169 0000:05:00.0: no dedicated PHY driver found for PHY ID 0x001cc862, maybe realtek.ko needs to be added to initramfs?
>> [ 3.184912] r8169: probe of 0000:05:00.0 failed with error -49
>>
>> Thank you for your efforts.
>>
>> Please let me know if you need any further details.
>>
>>> ---
>>> drivers/net/ethernet/realtek/r8169.h | 1 +
>>> drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
>>> .../net/ethernet/realtek/r8169_phy_config.c | 1 +
>>> 3 files changed, 77 insertions(+), 16 deletions(-)
>>>
>>> diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
>>> index 81567fcf3..c921456ed 100644
>>> --- a/drivers/net/ethernet/realtek/r8169.h
>>> +++ b/drivers/net/ethernet/realtek/r8169.h
>>> @@ -68,6 +68,7 @@ enum mac_version {
>>> /* support for RTL_GIGA_MAC_VER_60 has been removed */
>>> RTL_GIGA_MAC_VER_61,
>>> RTL_GIGA_MAC_VER_63,
>>> + RTL_GIGA_MAC_VER_65,
>>> RTL_GIGA_MAC_NONE
>>> };
>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>> index e0abdbcfa..ebf7a3b13 100644
>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>> @@ -55,6 +55,7 @@
>>> #define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
>>> #define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
>>> #define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
>>> +#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
>>> #define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
>>> #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
>>> @@ -136,6 +137,7 @@ static const struct {
>>> [RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
>>> /* reserve 62 for CFG_METHOD_4 in the vendor driver */
>>> [RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
>>> + [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
>>> };
>>> static const struct pci_device_id rtl8169_pci_tbl[] = {
>>> @@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
>>> { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
>>> { 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
>>> { PCI_VDEVICE(REALTEK, 0x8125) },
>>> + { PCI_VDEVICE(REALTEK, 0x8126) },
>>> { PCI_VDEVICE(REALTEK, 0x3000) },
>>> {}
>>> };
>>> @@ -327,8 +330,12 @@ enum rtl8168_registers {
>>> };
>>> enum rtl8125_registers {
>>> + INT_CFG0_8125 = 0x34,
>>> +#define INT_CFG0_ENABLE_8125 BIT(0)
>>> +#define INT_CFG0_CLKREQEN BIT(3)
>>> IntrMask_8125 = 0x38,
>>> IntrStatus_8125 = 0x3c,
>>> + INT_CFG1_8125 = 0x7a,
>>> TxPoll_8125 = 0x90,
>>> MAC0_BKP = 0x19e0,
>>> EEE_TXIDLE_TIMER_8125 = 0x6048,
>>> @@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
>>> case RTL_GIGA_MAC_VER_31:
>>> r8168dp_2_mdio_write(tp, location, val);
>>> break;
>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>> r8168g_mdio_write(tp, location, val);
>>> break;
>>> default:
>>> @@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
>>> case RTL_GIGA_MAC_VER_28:
>>> case RTL_GIGA_MAC_VER_31:
>>> return r8168dp_2_mdio_read(tp, location);
>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>> return r8168g_mdio_read(tp, location);
>>> default:
>>> return r8169_mdio_read(tp, location);
>>> @@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
>>> break;
>>> case RTL_GIGA_MAC_VER_34:
>>> case RTL_GIGA_MAC_VER_37:
>>> - case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
>>> if (wolopts)
>>> rtl_mod_config2(tp, 0, PME_SIGNAL);
>>> else
>>> @@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
>>> u16 val;
>>> enum mac_version ver;
>>> } mac_info[] = {
>>> + /* 8126A family. */
>>> + { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
>>> +
>>> /* 8125B family. */
>>> { 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
>>> @@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
>>> break;
>>> case RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_65:
>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
>>> RX_PAUSE_SLOT_ON);
>>> break;
>>> @@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
>>> case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
>>> rtl_eri_set_bits(tp, 0xd4, 0x0c00);
>>> break;
>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
>>> break;
>>> default:
>>> @@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>> case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
>>> rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
>>> break;
>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
>>> break;
>>> default:
>>> @@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>> {
>>> + u8 val8;
>>> +
>>> if (tp->mac_version < RTL_GIGA_MAC_VER_32)
>>> return;
>>> @@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>> return;
>>> rtl_mod_config5(tp, 0, ASPM_en);
>>> - rtl_mod_config2(tp, 0, ClkReqEn);
>>> + switch (tp->mac_version) {
>>> + case RTL_GIGA_MAC_VER_65:
>>> + val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>> + break;
>>> + default:
>>> + rtl_mod_config2(tp, 0, ClkReqEn);
>>> + break;
>>> + }
>>> switch (tp->mac_version) {
>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>> /* reset ephy tx/rx disable timer */
>>> r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
>>> /* chip can trigger L1.2 */
>>> @@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>> } else {
>>> switch (tp->mac_version) {
>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>> r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
>>> break;
>>> default:
>>> break;
>>> }
>>> - rtl_mod_config2(tp, ClkReqEn, 0);
>>> + switch (tp->mac_version) {
>>> + case RTL_GIGA_MAC_VER_65:
>>> + val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>> + break;
>>> + default:
>>> + rtl_mod_config2(tp, ClkReqEn, 0);
>>> + break;
>>> + }
>>> rtl_mod_config5(tp, ASPM_en, 0);
>>> }
>>> }
>>> @@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>> /* disable new tx descriptor format */
>>> r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>> + RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
>>> +
>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>> + else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>> r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
>>> else
>>> - r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
>>> if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>> r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
>>> @@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>> r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
>>> r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
>>> r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
>>> + else
>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
>>> r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
>>> r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
>>> r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
>>> @@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>> rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>> - rtl8125b_config_eee_mac(tp);
>>> - else
>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_61)
>>> rtl8125a_config_eee_mac(tp);
>>> + else
>>> + rtl8125b_config_eee_mac(tp);
>>> rtl_disable_rxdvgate(tp);
>>> }
>>> @@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
>>> rtl_hw_start_8125_common(tp);
>>> }
>>> +static void rtl_hw_start_8126a(struct rtl8169_private *tp)
>>> +{
>>> + rtl_set_def_aspm_entry_latency(tp);
>>> + rtl_hw_start_8125_common(tp);
>>> +}
>>> +
>>> static void rtl_hw_config(struct rtl8169_private *tp)
>>> {
>>> static const rtl_generic_fct hw_configs[] = {
>>> @@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
>>> [RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
>>> [RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
>>> [RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
>>> + [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
>>> };
>>> if (hw_configs[tp->mac_version])
>>> @@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
>>> {
>>> int i;
>>> + RTL_W8(tp, INT_CFG0_8125, 0x00);
>>> +
>>> /* disable interrupt coalescing */
>>> - for (i = 0xa00; i < 0xb00; i += 4)
>>> - RTL_W32(tp, i, 0);
>>> + switch (tp->mac_version) {
>>> + case RTL_GIGA_MAC_VER_61:
>>> + for (i = 0xa00; i < 0xb00; i += 4)
>>> + RTL_W32(tp, i, 0);
>>> + break;
>>> + case RTL_GIGA_MAC_VER_63:
>>> + case RTL_GIGA_MAC_VER_65:
>>> + for (i = 0xa00; i < 0xa80; i += 4)
>>> + RTL_W32(tp, i, 0);
>>> + RTL_W16(tp, INT_CFG1_8125, 0x0000);
>>> + break;
>>> + default:
>>> + break;
>>> + }
>>> rtl_hw_config(tp);
>>> }
>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>> index b50f16786..badf78f81 100644
>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>> @@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
>>> [RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
>>> [RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
>>> [RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
>>> + [RTL_GIGA_MAC_VER_65] = NULL,
>>> };
>>> if (phy_configs[ver])
>>
> The followoing adds support for the integrated PHY.
> Please apply it on-top and re-test.
>
> ---
> drivers/net/phy/realtek.c | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> index 894172a3e..132784321 100644
> --- a/drivers/net/phy/realtek.c
> +++ b/drivers/net/phy/realtek.c
> @@ -1047,6 +1047,16 @@ static struct phy_driver realtek_drvs[] = {
> .resume = rtlgen_resume,
> .read_page = rtl821x_read_page,
> .write_page = rtl821x_write_page,
> + }, {
> + PHY_ID_MATCH_EXACT(0x001cc862),
> + .name = "RTL8251B 5Gbps PHY",
> + .get_features = rtl822x_get_features,
> + .config_aneg = rtl822x_config_aneg,
> + .read_status = rtl822x_read_status,
> + .suspend = genphy_suspend,
> + .resume = rtlgen_resume,
> + .read_page = rtl821x_read_page,
> + .write_page = rtl821x_write_page,
> }, {
> PHY_ID_MATCH_EXACT(0x001cc961),
> .name = "RTL8366RB Gigabit Ethernet",
Thank you !
I forward your 2nd patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with both patches for for me to test.
I just installed the test kernel provided with both patches.
Here is the dmesg | grep 8169 output using this new test kernel
[ 3.630222] r8169 0000:05:00.0: enabling device (0000 -> 0003)
[ 3.632148] r8169 0000:05:00.0 eth0: RTL8126A, e8:9c:25:78:c9:bf, XID 649, IRQ 207
[ 3.632150] r8169 0000:05:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 3.633218] r8169 0000:05:00.0 enp5s0: renamed from eth0
[ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
[ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
[ 4.236119] RTL8251B 5Gbps PHY r8169-0-500:00: attached PHY driver (mii_bus:phy_addr=r8169-0-500:00, irq=MAC)
[ 4.349625] r8169 0000:05:00.0 enp5s0: Link is Down
[ 7.858055] r8169 0000:05:00.0 enp5s0: Link is Up - 1Gbps/Full - flow control rx/tx
Although dmesg has these 2 error messages, I have network connectivity, ran a quick speed test and am getting the correct speeds.
[ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
[ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
Here is the 'lsmod | grep 8169' results so you can see what is loaded
r8169 114688 0 mdio_devres 12288 1 r8169
libphy 245760 3 r8169,mdio_devres,realtek I will continue to test and report back if there are any network issues.
--
Regards,
Joe
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-01-31 16:14 ` Joe Salmeri
@ 2024-01-31 20:40 ` Heiner Kallweit
2024-01-31 23:36 ` Joe Salmeri
0 siblings, 1 reply; 10+ messages in thread
From: Heiner Kallweit @ 2024-01-31 20:40 UTC (permalink / raw)
To: Joe Salmeri, netdev@vger.kernel.org, tiwai
On 31.01.2024 17:14, Joe Salmeri wrote:
> On 1/30/24 14:59, Heiner Kallweit wrote:
>> On 30.01.2024 17:34, Joe Salmeri wrote:
>>> On 1/29/24 17:19, Heiner Kallweit wrote:
>>>> On 29.01.2024 19:31, Joe Salmeri wrote:
>>>>> Hi,
>>>>>
>>>>> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>>>>>
>>>>> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>>>>>
>>>>> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>>>>>
>>>>> There does not seem to be a driver for the Realtek 8126.
>>>>>
>>>>> Here is the device info from "lspci | grep -i net"
>>>>>
>>>>> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
>>>>> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>>>>>
>>>>> So it is detects the 8126 just fine it just doesn't have a driver for it.
>>>>>
>>>>> I checked realtek.com and found
>>>>>
>>>>> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>>>>>
>>>>> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
>>>>> resulting module file.
>>>>>
>>>>> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>>>>>
>>>>> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
>>>>> is what is used to support the older Realtek 8125 device.
>>>>>
>>>>> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
>>>>> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>>>>>
>>>>> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>>>>>
>>>>> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>>>>>
>>>>> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>>>> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>>>>>
>>>>> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
>>>>> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>>>>>
>>>>> The details of the openSUSE bug report on the issue can be found here:
>>>>>
>>>>> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>>>>>
>>>>> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>>>>>
>>>> Thanks for the report. Actually it's not a bug report but a feature request.
>>>> Realtek provides no information about new chip versions and no data sheets, therefore the only
>>>> source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
>>>> handling, therefore the first steps you described go in the right direction, but are by far not
>>>> sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
>>>>
>>>> Disclaimer:
>>>> r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
>>>> Typically the firmware files tune PHY parameters to deal with compatibility issues.
>>>> In addition r8125 includes a lot of PHY tuning for RTL8126A.
>>>> Depending on cabling, link partner etc. the patch may work for you, or you may experience
>>>> link instability or worst case no link at all.
>>>>
>>>> Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
>>>> In this case the driver will complain with the following message and I'd need the PHY ID.
>>>> "no dedicated PHY driver found for PHY ID xxx"
>>> Thanks very much for your quick response.
>>>
>>> I forward your patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with the patches for for me to test.
>>>
>>> I just installed the test kernel provided with the patches but just as you expected it complains about no dedicated PHY driver found.
>>>
>>> Here is the dmesg | grep 8169 output with the information you requested
>>>
>>> [ 3.176753] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>> [ 3.184887] r8169 0000:05:00.0: no dedicated PHY driver found for PHY ID 0x001cc862, maybe realtek.ko needs to be added to initramfs?
>>> [ 3.184912] r8169: probe of 0000:05:00.0 failed with error -49
>>>
>>> Thank you for your efforts.
>>>
>>> Please let me know if you need any further details.
>>>
>>>> ---
>>>> drivers/net/ethernet/realtek/r8169.h | 1 +
>>>> drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
>>>> .../net/ethernet/realtek/r8169_phy_config.c | 1 +
>>>> 3 files changed, 77 insertions(+), 16 deletions(-)
>>>>
>>>> diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
>>>> index 81567fcf3..c921456ed 100644
>>>> --- a/drivers/net/ethernet/realtek/r8169.h
>>>> +++ b/drivers/net/ethernet/realtek/r8169.h
>>>> @@ -68,6 +68,7 @@ enum mac_version {
>>>> /* support for RTL_GIGA_MAC_VER_60 has been removed */
>>>> RTL_GIGA_MAC_VER_61,
>>>> RTL_GIGA_MAC_VER_63,
>>>> + RTL_GIGA_MAC_VER_65,
>>>> RTL_GIGA_MAC_NONE
>>>> };
>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>> index e0abdbcfa..ebf7a3b13 100644
>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>> @@ -55,6 +55,7 @@
>>>> #define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
>>>> #define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
>>>> #define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
>>>> +#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
>>>> #define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
>>>> #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
>>>> @@ -136,6 +137,7 @@ static const struct {
>>>> [RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
>>>> /* reserve 62 for CFG_METHOD_4 in the vendor driver */
>>>> [RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
>>>> + [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
>>>> };
>>>> static const struct pci_device_id rtl8169_pci_tbl[] = {
>>>> @@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
>>>> { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
>>>> { 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
>>>> { PCI_VDEVICE(REALTEK, 0x8125) },
>>>> + { PCI_VDEVICE(REALTEK, 0x8126) },
>>>> { PCI_VDEVICE(REALTEK, 0x3000) },
>>>> {}
>>>> };
>>>> @@ -327,8 +330,12 @@ enum rtl8168_registers {
>>>> };
>>>> enum rtl8125_registers {
>>>> + INT_CFG0_8125 = 0x34,
>>>> +#define INT_CFG0_ENABLE_8125 BIT(0)
>>>> +#define INT_CFG0_CLKREQEN BIT(3)
>>>> IntrMask_8125 = 0x38,
>>>> IntrStatus_8125 = 0x3c,
>>>> + INT_CFG1_8125 = 0x7a,
>>>> TxPoll_8125 = 0x90,
>>>> MAC0_BKP = 0x19e0,
>>>> EEE_TXIDLE_TIMER_8125 = 0x6048,
>>>> @@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
>>>> case RTL_GIGA_MAC_VER_31:
>>>> r8168dp_2_mdio_write(tp, location, val);
>>>> break;
>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>> r8168g_mdio_write(tp, location, val);
>>>> break;
>>>> default:
>>>> @@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
>>>> case RTL_GIGA_MAC_VER_28:
>>>> case RTL_GIGA_MAC_VER_31:
>>>> return r8168dp_2_mdio_read(tp, location);
>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>> return r8168g_mdio_read(tp, location);
>>>> default:
>>>> return r8169_mdio_read(tp, location);
>>>> @@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
>>>> break;
>>>> case RTL_GIGA_MAC_VER_34:
>>>> case RTL_GIGA_MAC_VER_37:
>>>> - case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
>>>> if (wolopts)
>>>> rtl_mod_config2(tp, 0, PME_SIGNAL);
>>>> else
>>>> @@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
>>>> u16 val;
>>>> enum mac_version ver;
>>>> } mac_info[] = {
>>>> + /* 8126A family. */
>>>> + { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
>>>> +
>>>> /* 8125B family. */
>>>> { 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
>>>> @@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
>>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
>>>> break;
>>>> case RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_65:
>>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
>>>> RX_PAUSE_SLOT_ON);
>>>> break;
>>>> @@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
>>>> case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
>>>> rtl_eri_set_bits(tp, 0xd4, 0x0c00);
>>>> break;
>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
>>>> break;
>>>> default:
>>>> @@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>>> case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
>>>> rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
>>>> break;
>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
>>>> break;
>>>> default:
>>>> @@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>>> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>> {
>>>> + u8 val8;
>>>> +
>>>> if (tp->mac_version < RTL_GIGA_MAC_VER_32)
>>>> return;
>>>> @@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>> return;
>>>> rtl_mod_config5(tp, 0, ASPM_en);
>>>> - rtl_mod_config2(tp, 0, ClkReqEn);
>>>> + switch (tp->mac_version) {
>>>> + case RTL_GIGA_MAC_VER_65:
>>>> + val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
>>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>>> + break;
>>>> + default:
>>>> + rtl_mod_config2(tp, 0, ClkReqEn);
>>>> + break;
>>>> + }
>>>> switch (tp->mac_version) {
>>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>>> /* reset ephy tx/rx disable timer */
>>>> r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
>>>> /* chip can trigger L1.2 */
>>>> @@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>> } else {
>>>> switch (tp->mac_version) {
>>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>>> r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
>>>> break;
>>>> default:
>>>> break;
>>>> }
>>>> - rtl_mod_config2(tp, ClkReqEn, 0);
>>>> + switch (tp->mac_version) {
>>>> + case RTL_GIGA_MAC_VER_65:
>>>> + val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
>>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>>> + break;
>>>> + default:
>>>> + rtl_mod_config2(tp, ClkReqEn, 0);
>>>> + break;
>>>> + }
>>>> rtl_mod_config5(tp, ASPM_en, 0);
>>>> }
>>>> }
>>>> @@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>> /* disable new tx descriptor format */
>>>> r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
>>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>> + RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
>>>> +
>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>>> + else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>> r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
>>>> else
>>>> - r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
>>>> if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>> r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
>>>> @@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>> r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
>>>> r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
>>>> r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
>>>> + else
>>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
>>>> r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
>>>> r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
>>>> r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
>>>> @@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>> rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
>>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>> - rtl8125b_config_eee_mac(tp);
>>>> - else
>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_61)
>>>> rtl8125a_config_eee_mac(tp);
>>>> + else
>>>> + rtl8125b_config_eee_mac(tp);
>>>> rtl_disable_rxdvgate(tp);
>>>> }
>>>> @@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
>>>> rtl_hw_start_8125_common(tp);
>>>> }
>>>> +static void rtl_hw_start_8126a(struct rtl8169_private *tp)
>>>> +{
>>>> + rtl_set_def_aspm_entry_latency(tp);
>>>> + rtl_hw_start_8125_common(tp);
>>>> +}
>>>> +
>>>> static void rtl_hw_config(struct rtl8169_private *tp)
>>>> {
>>>> static const rtl_generic_fct hw_configs[] = {
>>>> @@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
>>>> [RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
>>>> [RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
>>>> [RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
>>>> + [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
>>>> };
>>>> if (hw_configs[tp->mac_version])
>>>> @@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
>>>> {
>>>> int i;
>>>> + RTL_W8(tp, INT_CFG0_8125, 0x00);
>>>> +
>>>> /* disable interrupt coalescing */
>>>> - for (i = 0xa00; i < 0xb00; i += 4)
>>>> - RTL_W32(tp, i, 0);
>>>> + switch (tp->mac_version) {
>>>> + case RTL_GIGA_MAC_VER_61:
>>>> + for (i = 0xa00; i < 0xb00; i += 4)
>>>> + RTL_W32(tp, i, 0);
>>>> + break;
>>>> + case RTL_GIGA_MAC_VER_63:
>>>> + case RTL_GIGA_MAC_VER_65:
>>>> + for (i = 0xa00; i < 0xa80; i += 4)
>>>> + RTL_W32(tp, i, 0);
>>>> + RTL_W16(tp, INT_CFG1_8125, 0x0000);
>>>> + break;
>>>> + default:
>>>> + break;
>>>> + }
>>>> rtl_hw_config(tp);
>>>> }
>>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>> index b50f16786..badf78f81 100644
>>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>> @@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
>>>> [RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
>>>> [RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
>>>> [RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
>>>> + [RTL_GIGA_MAC_VER_65] = NULL,
>>>> };
>>>> if (phy_configs[ver])
>>>
>> The followoing adds support for the integrated PHY.
>> Please apply it on-top and re-test.
>>
>> ---
>> drivers/net/phy/realtek.c | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>>
>> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
>> index 894172a3e..132784321 100644
>> --- a/drivers/net/phy/realtek.c
>> +++ b/drivers/net/phy/realtek.c
>> @@ -1047,6 +1047,16 @@ static struct phy_driver realtek_drvs[] = {
>> .resume = rtlgen_resume,
>> .read_page = rtl821x_read_page,
>> .write_page = rtl821x_write_page,
>> + }, {
>> + PHY_ID_MATCH_EXACT(0x001cc862),
>> + .name = "RTL8251B 5Gbps PHY",
>> + .get_features = rtl822x_get_features,
>> + .config_aneg = rtl822x_config_aneg,
>> + .read_status = rtl822x_read_status,
>> + .suspend = genphy_suspend,
>> + .resume = rtlgen_resume,
>> + .read_page = rtl821x_read_page,
>> + .write_page = rtl821x_write_page,
>> }, {
>> PHY_ID_MATCH_EXACT(0x001cc961),
>> .name = "RTL8366RB Gigabit Ethernet",
>
> Thank you !
>
> I forward your 2nd patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with both patches for for me to test.
>
> I just installed the test kernel provided with both patches.
>
> Here is the dmesg | grep 8169 output using this new test kernel
>
> [ 3.630222] r8169 0000:05:00.0: enabling device (0000 -> 0003)
> [ 3.632148] r8169 0000:05:00.0 eth0: RTL8126A, e8:9c:25:78:c9:bf, XID 649, IRQ 207
> [ 3.632150] r8169 0000:05:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
> [ 3.633218] r8169 0000:05:00.0 enp5s0: renamed from eth0
> [ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
> [ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
> [ 4.236119] RTL8251B 5Gbps PHY r8169-0-500:00: attached PHY driver (mii_bus:phy_addr=r8169-0-500:00, irq=MAC)
> [ 4.349625] r8169 0000:05:00.0 enp5s0: Link is Down
> [ 7.858055] r8169 0000:05:00.0 enp5s0: Link is Up - 1Gbps/Full - flow control rx/tx
>
> Although dmesg has these 2 error messages, I have network connectivity, ran a quick speed test and am getting the correct speeds.
>
Thanks for the feedback. The firmware-related errors are expected, Realtek didn't provide the
firmware file to linux-firmware yet. I contacted Realtek in this matter.
Based on the experimental patches I'll prepare support for RTL8126A, and it should show up
in kernel version 6.9.
> [ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
> [ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
>
> Here is the 'lsmod | grep 8169' results so you can see what is loaded
>
> r8169 114688 0 mdio_devres 12288 1 r8169 libphy 245760 3 r8169,mdio_devres,realtek I will continue to test and report back if there are any network issues.
>
Please do so. Thank you
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-01-31 20:40 ` Heiner Kallweit
@ 2024-01-31 23:36 ` Joe Salmeri
2024-02-01 7:09 ` Heiner Kallweit
0 siblings, 1 reply; 10+ messages in thread
From: Joe Salmeri @ 2024-01-31 23:36 UTC (permalink / raw)
To: Heiner Kallweit, netdev@vger.kernel.org, tiwai
On 1/31/24 15:40, Heiner Kallweit wrote:
> On 31.01.2024 17:14, Joe Salmeri wrote:
>> On 1/30/24 14:59, Heiner Kallweit wrote:
>>> On 30.01.2024 17:34, Joe Salmeri wrote:
>>>> On 1/29/24 17:19, Heiner Kallweit wrote:
>>>>> On 29.01.2024 19:31, Joe Salmeri wrote:
>>>>>> Hi,
>>>>>>
>>>>>> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>>>>>>
>>>>>> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>>>>>>
>>>>>> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>>>>>>
>>>>>> There does not seem to be a driver for the Realtek 8126.
>>>>>>
>>>>>> Here is the device info from "lspci | grep -i net"
>>>>>>
>>>>>> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
>>>>>> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>>>>>>
>>>>>> So it is detects the 8126 just fine it just doesn't have a driver for it.
>>>>>>
>>>>>> I checked realtek.com and found
>>>>>>
>>>>>> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>>>>>>
>>>>>> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
>>>>>> resulting module file.
>>>>>>
>>>>>> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>>>>>>
>>>>>> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
>>>>>> is what is used to support the older Realtek 8125 device.
>>>>>>
>>>>>> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
>>>>>> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>>>>>>
>>>>>> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>>>>>>
>>>>>> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>>>>>>
>>>>>> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>>>>> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>>>>>>
>>>>>> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
>>>>>> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>>>>>>
>>>>>> The details of the openSUSE bug report on the issue can be found here:
>>>>>>
>>>>>> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>>>>>>
>>>>>> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>>>>>>
>>>>> Thanks for the report. Actually it's not a bug report but a feature request.
>>>>> Realtek provides no information about new chip versions and no data sheets, therefore the only
>>>>> source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
>>>>> handling, therefore the first steps you described go in the right direction, but are by far not
>>>>> sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
>>>>>
>>>>> Disclaimer:
>>>>> r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
>>>>> Typically the firmware files tune PHY parameters to deal with compatibility issues.
>>>>> In addition r8125 includes a lot of PHY tuning for RTL8126A.
>>>>> Depending on cabling, link partner etc. the patch may work for you, or you may experience
>>>>> link instability or worst case no link at all.
>>>>>
>>>>> Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
>>>>> In this case the driver will complain with the following message and I'd need the PHY ID.
>>>>> "no dedicated PHY driver found for PHY ID xxx"
>>>> Thanks very much for your quick response.
>>>>
>>>> I forward your patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with the patches for for me to test.
>>>>
>>>> I just installed the test kernel provided with the patches but just as you expected it complains about no dedicated PHY driver found.
>>>>
>>>> Here is the dmesg | grep 8169 output with the information you requested
>>>>
>>>> [ 3.176753] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>>> [ 3.184887] r8169 0000:05:00.0: no dedicated PHY driver found for PHY ID 0x001cc862, maybe realtek.ko needs to be added to initramfs?
>>>> [ 3.184912] r8169: probe of 0000:05:00.0 failed with error -49
>>>>
>>>> Thank you for your efforts.
>>>>
>>>> Please let me know if you need any further details.
>>>>
>>>>> ---
>>>>> drivers/net/ethernet/realtek/r8169.h | 1 +
>>>>> drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
>>>>> .../net/ethernet/realtek/r8169_phy_config.c | 1 +
>>>>> 3 files changed, 77 insertions(+), 16 deletions(-)
>>>>>
>>>>> diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
>>>>> index 81567fcf3..c921456ed 100644
>>>>> --- a/drivers/net/ethernet/realtek/r8169.h
>>>>> +++ b/drivers/net/ethernet/realtek/r8169.h
>>>>> @@ -68,6 +68,7 @@ enum mac_version {
>>>>> /* support for RTL_GIGA_MAC_VER_60 has been removed */
>>>>> RTL_GIGA_MAC_VER_61,
>>>>> RTL_GIGA_MAC_VER_63,
>>>>> + RTL_GIGA_MAC_VER_65,
>>>>> RTL_GIGA_MAC_NONE
>>>>> };
>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>>> index e0abdbcfa..ebf7a3b13 100644
>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>>> @@ -55,6 +55,7 @@
>>>>> #define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
>>>>> #define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
>>>>> #define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
>>>>> +#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
>>>>> #define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
>>>>> #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
>>>>> @@ -136,6 +137,7 @@ static const struct {
>>>>> [RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
>>>>> /* reserve 62 for CFG_METHOD_4 in the vendor driver */
>>>>> [RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
>>>>> + [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
>>>>> };
>>>>> static const struct pci_device_id rtl8169_pci_tbl[] = {
>>>>> @@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
>>>>> { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
>>>>> { 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
>>>>> { PCI_VDEVICE(REALTEK, 0x8125) },
>>>>> + { PCI_VDEVICE(REALTEK, 0x8126) },
>>>>> { PCI_VDEVICE(REALTEK, 0x3000) },
>>>>> {}
>>>>> };
>>>>> @@ -327,8 +330,12 @@ enum rtl8168_registers {
>>>>> };
>>>>> enum rtl8125_registers {
>>>>> + INT_CFG0_8125 = 0x34,
>>>>> +#define INT_CFG0_ENABLE_8125 BIT(0)
>>>>> +#define INT_CFG0_CLKREQEN BIT(3)
>>>>> IntrMask_8125 = 0x38,
>>>>> IntrStatus_8125 = 0x3c,
>>>>> + INT_CFG1_8125 = 0x7a,
>>>>> TxPoll_8125 = 0x90,
>>>>> MAC0_BKP = 0x19e0,
>>>>> EEE_TXIDLE_TIMER_8125 = 0x6048,
>>>>> @@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
>>>>> case RTL_GIGA_MAC_VER_31:
>>>>> r8168dp_2_mdio_write(tp, location, val);
>>>>> break;
>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>> r8168g_mdio_write(tp, location, val);
>>>>> break;
>>>>> default:
>>>>> @@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
>>>>> case RTL_GIGA_MAC_VER_28:
>>>>> case RTL_GIGA_MAC_VER_31:
>>>>> return r8168dp_2_mdio_read(tp, location);
>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>> return r8168g_mdio_read(tp, location);
>>>>> default:
>>>>> return r8169_mdio_read(tp, location);
>>>>> @@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
>>>>> break;
>>>>> case RTL_GIGA_MAC_VER_34:
>>>>> case RTL_GIGA_MAC_VER_37:
>>>>> - case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
>>>>> if (wolopts)
>>>>> rtl_mod_config2(tp, 0, PME_SIGNAL);
>>>>> else
>>>>> @@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
>>>>> u16 val;
>>>>> enum mac_version ver;
>>>>> } mac_info[] = {
>>>>> + /* 8126A family. */
>>>>> + { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
>>>>> +
>>>>> /* 8125B family. */
>>>>> { 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
>>>>> @@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
>>>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
>>>>> break;
>>>>> case RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
>>>>> RX_PAUSE_SLOT_ON);
>>>>> break;
>>>>> @@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
>>>>> case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
>>>>> rtl_eri_set_bits(tp, 0xd4, 0x0c00);
>>>>> break;
>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
>>>>> break;
>>>>> default:
>>>>> @@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>>>> case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
>>>>> rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
>>>>> break;
>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
>>>>> break;
>>>>> default:
>>>>> @@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>>>> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>>> {
>>>>> + u8 val8;
>>>>> +
>>>>> if (tp->mac_version < RTL_GIGA_MAC_VER_32)
>>>>> return;
>>>>> @@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>>> return;
>>>>> rtl_mod_config5(tp, 0, ASPM_en);
>>>>> - rtl_mod_config2(tp, 0, ClkReqEn);
>>>>> + switch (tp->mac_version) {
>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>> + val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
>>>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>>>> + break;
>>>>> + default:
>>>>> + rtl_mod_config2(tp, 0, ClkReqEn);
>>>>> + break;
>>>>> + }
>>>>> switch (tp->mac_version) {
>>>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>>>> /* reset ephy tx/rx disable timer */
>>>>> r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
>>>>> /* chip can trigger L1.2 */
>>>>> @@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>>> } else {
>>>>> switch (tp->mac_version) {
>>>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>>>> r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
>>>>> break;
>>>>> default:
>>>>> break;
>>>>> }
>>>>> - rtl_mod_config2(tp, ClkReqEn, 0);
>>>>> + switch (tp->mac_version) {
>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>> + val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
>>>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>>>> + break;
>>>>> + default:
>>>>> + rtl_mod_config2(tp, ClkReqEn, 0);
>>>>> + break;
>>>>> + }
>>>>> rtl_mod_config5(tp, ASPM_en, 0);
>>>>> }
>>>>> }
>>>>> @@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>>> /* disable new tx descriptor format */
>>>>> r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
>>>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>>> + RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
>>>>> +
>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>>>> + else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>> r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
>>>>> else
>>>>> - r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
>>>>> if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>> r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
>>>>> @@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>>> r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
>>>>> r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
>>>>> r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
>>>>> + else
>>>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
>>>>> r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
>>>>> r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
>>>>> r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
>>>>> @@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>>> rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
>>>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>> - rtl8125b_config_eee_mac(tp);
>>>>> - else
>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_61)
>>>>> rtl8125a_config_eee_mac(tp);
>>>>> + else
>>>>> + rtl8125b_config_eee_mac(tp);
>>>>> rtl_disable_rxdvgate(tp);
>>>>> }
>>>>> @@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
>>>>> rtl_hw_start_8125_common(tp);
>>>>> }
>>>>> +static void rtl_hw_start_8126a(struct rtl8169_private *tp)
>>>>> +{
>>>>> + rtl_set_def_aspm_entry_latency(tp);
>>>>> + rtl_hw_start_8125_common(tp);
>>>>> +}
>>>>> +
>>>>> static void rtl_hw_config(struct rtl8169_private *tp)
>>>>> {
>>>>> static const rtl_generic_fct hw_configs[] = {
>>>>> @@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
>>>>> [RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
>>>>> [RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
>>>>> [RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
>>>>> + [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
>>>>> };
>>>>> if (hw_configs[tp->mac_version])
>>>>> @@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
>>>>> {
>>>>> int i;
>>>>> + RTL_W8(tp, INT_CFG0_8125, 0x00);
>>>>> +
>>>>> /* disable interrupt coalescing */
>>>>> - for (i = 0xa00; i < 0xb00; i += 4)
>>>>> - RTL_W32(tp, i, 0);
>>>>> + switch (tp->mac_version) {
>>>>> + case RTL_GIGA_MAC_VER_61:
>>>>> + for (i = 0xa00; i < 0xb00; i += 4)
>>>>> + RTL_W32(tp, i, 0);
>>>>> + break;
>>>>> + case RTL_GIGA_MAC_VER_63:
>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>> + for (i = 0xa00; i < 0xa80; i += 4)
>>>>> + RTL_W32(tp, i, 0);
>>>>> + RTL_W16(tp, INT_CFG1_8125, 0x0000);
>>>>> + break;
>>>>> + default:
>>>>> + break;
>>>>> + }
>>>>> rtl_hw_config(tp);
>>>>> }
>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>> index b50f16786..badf78f81 100644
>>>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>> @@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
>>>>> [RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
>>>>> [RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
>>>>> [RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
>>>>> + [RTL_GIGA_MAC_VER_65] = NULL,
>>>>> };
>>>>> if (phy_configs[ver])
>>> The followoing adds support for the integrated PHY.
>>> Please apply it on-top and re-test.
>>>
>>> ---
>>> drivers/net/phy/realtek.c | 10 ++++++++++
>>> 1 file changed, 10 insertions(+)
>>>
>>> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
>>> index 894172a3e..132784321 100644
>>> --- a/drivers/net/phy/realtek.c
>>> +++ b/drivers/net/phy/realtek.c
>>> @@ -1047,6 +1047,16 @@ static struct phy_driver realtek_drvs[] = {
>>> .resume = rtlgen_resume,
>>> .read_page = rtl821x_read_page,
>>> .write_page = rtl821x_write_page,
>>> + }, {
>>> + PHY_ID_MATCH_EXACT(0x001cc862),
>>> + .name = "RTL8251B 5Gbps PHY",
>>> + .get_features = rtl822x_get_features,
>>> + .config_aneg = rtl822x_config_aneg,
>>> + .read_status = rtl822x_read_status,
>>> + .suspend = genphy_suspend,
>>> + .resume = rtlgen_resume,
>>> + .read_page = rtl821x_read_page,
>>> + .write_page = rtl821x_write_page,
>>> }, {
>>> PHY_ID_MATCH_EXACT(0x001cc961),
>>> .name = "RTL8366RB Gigabit Ethernet",
>> Thank you !
>>
>> I forward your 2nd patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with both patches for for me to test.
>>
>> I just installed the test kernel provided with both patches.
>>
>> Here is the dmesg | grep 8169 output using this new test kernel
>>
>> [ 3.630222] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>> [ 3.632148] r8169 0000:05:00.0 eth0: RTL8126A, e8:9c:25:78:c9:bf, XID 649, IRQ 207
>> [ 3.632150] r8169 0000:05:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
>> [ 3.633218] r8169 0000:05:00.0 enp5s0: renamed from eth0
>> [ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
>> [ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
>> [ 4.236119] RTL8251B 5Gbps PHY r8169-0-500:00: attached PHY driver (mii_bus:phy_addr=r8169-0-500:00, irq=MAC)
>> [ 4.349625] r8169 0000:05:00.0 enp5s0: Link is Down
>> [ 7.858055] r8169 0000:05:00.0 enp5s0: Link is Up - 1Gbps/Full - flow control rx/tx
>>
>> Although dmesg has these 2 error messages, I have network connectivity, ran a quick speed test and am getting the correct speeds.
>>
> Thanks for the feedback. The firmware-related errors are expected, Realtek didn't provide the
> firmware file to linux-firmware yet. I contacted Realtek in this matter.
> Based on the experimental patches I'll prepare support for RTL8126A, and it should show up
> in kernel version 6.9.
THANK YOU for all your efforts they are greatly appreciated !
I remember you mentioned about not having the firmware from Realtek but
wasn't sure if the errors might mean I would run into issues.
So far everything has been working fine all day.
Thanks for contacting Realtek about the firmware.
You mentioned support showing up in the 6.9 kernel. Was that correct
or did you mean 6.8 which comes out in March ?
>> [ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
>> [ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
>>
>> Here is the 'lsmod | grep 8169' results so you can see what is loaded
>>
>> r8169 114688 0 mdio_devres 12288 1 r8169 libphy 245760 3 r8169,mdio_devres,realtek I will continue to test and report back if there are any network issues.
>>
> Please do so. Thank you
>
--
Regards,
Joe
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-01-31 23:36 ` Joe Salmeri
@ 2024-02-01 7:09 ` Heiner Kallweit
2024-02-01 7:19 ` Takashi Iwai
0 siblings, 1 reply; 10+ messages in thread
From: Heiner Kallweit @ 2024-02-01 7:09 UTC (permalink / raw)
To: Joe Salmeri, netdev@vger.kernel.org, tiwai
On 01.02.2024 00:36, Joe Salmeri wrote:
> On 1/31/24 15:40, Heiner Kallweit wrote:
>> On 31.01.2024 17:14, Joe Salmeri wrote:
>>> On 1/30/24 14:59, Heiner Kallweit wrote:
>>>> On 30.01.2024 17:34, Joe Salmeri wrote:
>>>>> On 1/29/24 17:19, Heiner Kallweit wrote:
>>>>>> On 29.01.2024 19:31, Joe Salmeri wrote:
>>>>>>> Hi,
>>>>>>>
>>>>>>> I recently built a new PC using the Asus z790 Maximus Formula motherboard.
>>>>>>>
>>>>>>> The z790 Formula uses the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter.
>>>>>>>
>>>>>>> I am using openSUSE Tumbleweed build 20231228 with kernel 6.6.7-1
>>>>>>>
>>>>>>> There does not seem to be a driver for the Realtek 8126.
>>>>>>>
>>>>>>> Here is the device info from "lspci | grep -i net"
>>>>>>>
>>>>>>> 04:00.0 Network controller: Intel Corporation Device 272b (rev 1a)
>>>>>>> 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8126 (rev 01)
>>>>>>>
>>>>>>> So it is detects the 8126 just fine it just doesn't have a driver for it.
>>>>>>>
>>>>>>> I checked realtek.com and found
>>>>>>>
>>>>>>> https://www.realtek.com/en/component/zoo/category/network-interface-controllers-10-100-1000m-gigabit-ethernet-pci-express-software
>>>>>>>
>>>>>>> The download link still says 8125 ( and kernel 6.4 ), but I compiled the source and since I have Secure boot enabled, I signed the
>>>>>>> resulting module file.
>>>>>>>
>>>>>>> The driver loads successfully and I now have wired networking and it has worked flawlessly for the last 2 months.
>>>>>>>
>>>>>>> I submitted a bug in Tumbleweed requesting support for the Realtek 8126 be added and was informed that the r8169 kernel module
>>>>>>> is what is used to support the older Realtek 8125 device.
>>>>>>>
>>>>>>> Since the drivers from Realtek seem to support both the r8125 and my newer r8126, the Tumbleweed support prepared a test
>>>>>>> kernel 6.6.7-1 for me where they added the PCI entry for the r8126 and I installed and tested it out.
>>>>>>>
>>>>>>> Although it does now load the r8169 module with their test kernel, the r8126 device still does not work.
>>>>>>>
>>>>>>> The only 2 lines that reference the r8169 in the dmesg log are these 2 lines:
>>>>>>>
>>>>>>> [ 3.237151] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>>>>>> [ 3.237289] r8169 0000:05:00.0: error -ENODEV: unknown chip XID 649, contact r8169 maintainers (see MAINTAINERS file)
>>>>>>>
>>>>>>> I reported the results of the test to Tumbleweed support and they said that additional tweaks will be needed for the r8169
>>>>>>> module to support the r8126 wired network adapter and thatn I should request to you to add support.
>>>>>>>
>>>>>>> The details of the openSUSE bug report on the issue can be found here:
>>>>>>>
>>>>>>> https://bugzilla.suse.com/show_bug.cgi?id=1217417
>>>>>>>
>>>>>>> Could we please get support added for the r8126 - Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter added to the kernel ?
>>>>>>>
>>>>>> Thanks for the report. Actually it's not a bug report but a feature request.
>>>>>> Realtek provides no information about new chip versions and no data sheets, therefore the only
>>>>>> source of information is the r8125 vendor driver. Each chip requires a lot of version-specific
>>>>>> handling, therefore the first steps you described go in the right direction, but are by far not
>>>>>> sufficient. Patch below applies on linux-next, please test whether it works for you, and report back.
>>>>>>
>>>>>> Disclaimer:
>>>>>> r8125 references a firmware file that hasn't been provided to linux-firmware by Realtek yet.
>>>>>> Typically the firmware files tune PHY parameters to deal with compatibility issues.
>>>>>> In addition r8125 includes a lot of PHY tuning for RTL8126A.
>>>>>> Depending on cabling, link partner etc. the patch may work for you, or you may experience
>>>>>> link instability or worst case no link at all.
>>>>>>
>>>>>> Maybe RTL8126a also has a new integrated PHY version that isn't supported yet.
>>>>>> In this case the driver will complain with the following message and I'd need the PHY ID.
>>>>>> "no dedicated PHY driver found for PHY ID xxx"
>>>>> Thanks very much for your quick response.
>>>>>
>>>>> I forward your patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with the patches for for me to test.
>>>>>
>>>>> I just installed the test kernel provided with the patches but just as you expected it complains about no dedicated PHY driver found.
>>>>>
>>>>> Here is the dmesg | grep 8169 output with the information you requested
>>>>>
>>>>> [ 3.176753] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>>>> [ 3.184887] r8169 0000:05:00.0: no dedicated PHY driver found for PHY ID 0x001cc862, maybe realtek.ko needs to be added to initramfs?
>>>>> [ 3.184912] r8169: probe of 0000:05:00.0 failed with error -49
>>>>>
>>>>> Thank you for your efforts.
>>>>>
>>>>> Please let me know if you need any further details.
>>>>>
>>>>>> ---
>>>>>> drivers/net/ethernet/realtek/r8169.h | 1 +
>>>>>> drivers/net/ethernet/realtek/r8169_main.c | 91 +++++++++++++++----
>>>>>> .../net/ethernet/realtek/r8169_phy_config.c | 1 +
>>>>>> 3 files changed, 77 insertions(+), 16 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169.h b/drivers/net/ethernet/realtek/r8169.h
>>>>>> index 81567fcf3..c921456ed 100644
>>>>>> --- a/drivers/net/ethernet/realtek/r8169.h
>>>>>> +++ b/drivers/net/ethernet/realtek/r8169.h
>>>>>> @@ -68,6 +68,7 @@ enum mac_version {
>>>>>> /* support for RTL_GIGA_MAC_VER_60 has been removed */
>>>>>> RTL_GIGA_MAC_VER_61,
>>>>>> RTL_GIGA_MAC_VER_63,
>>>>>> + RTL_GIGA_MAC_VER_65,
>>>>>> RTL_GIGA_MAC_NONE
>>>>>> };
>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>> index e0abdbcfa..ebf7a3b13 100644
>>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>> @@ -55,6 +55,7 @@
>>>>>> #define FIRMWARE_8107E_2 "rtl_nic/rtl8107e-2.fw"
>>>>>> #define FIRMWARE_8125A_3 "rtl_nic/rtl8125a-3.fw"
>>>>>> #define FIRMWARE_8125B_2 "rtl_nic/rtl8125b-2.fw"
>>>>>> +#define FIRMWARE_8126A_2 "rtl_nic/rtl8126a-2.fw"
>>>>>> #define TX_DMA_BURST 7 /* Maximum PCI burst, '7' is unlimited */
>>>>>> #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
>>>>>> @@ -136,6 +137,7 @@ static const struct {
>>>>>> [RTL_GIGA_MAC_VER_61] = {"RTL8125A", FIRMWARE_8125A_3},
>>>>>> /* reserve 62 for CFG_METHOD_4 in the vendor driver */
>>>>>> [RTL_GIGA_MAC_VER_63] = {"RTL8125B", FIRMWARE_8125B_2},
>>>>>> + [RTL_GIGA_MAC_VER_65] = {"RTL8126A", FIRMWARE_8126A_2},
>>>>>> };
>>>>>> static const struct pci_device_id rtl8169_pci_tbl[] = {
>>>>>> @@ -158,6 +160,7 @@ static const struct pci_device_id rtl8169_pci_tbl[] = {
>>>>>> { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024 },
>>>>>> { 0x0001, 0x8168, PCI_ANY_ID, 0x2410 },
>>>>>> { PCI_VDEVICE(REALTEK, 0x8125) },
>>>>>> + { PCI_VDEVICE(REALTEK, 0x8126) },
>>>>>> { PCI_VDEVICE(REALTEK, 0x3000) },
>>>>>> {}
>>>>>> };
>>>>>> @@ -327,8 +330,12 @@ enum rtl8168_registers {
>>>>>> };
>>>>>> enum rtl8125_registers {
>>>>>> + INT_CFG0_8125 = 0x34,
>>>>>> +#define INT_CFG0_ENABLE_8125 BIT(0)
>>>>>> +#define INT_CFG0_CLKREQEN BIT(3)
>>>>>> IntrMask_8125 = 0x38,
>>>>>> IntrStatus_8125 = 0x3c,
>>>>>> + INT_CFG1_8125 = 0x7a,
>>>>>> TxPoll_8125 = 0x90,
>>>>>> MAC0_BKP = 0x19e0,
>>>>>> EEE_TXIDLE_TIMER_8125 = 0x6048,
>>>>>> @@ -1139,7 +1146,7 @@ static void rtl_writephy(struct rtl8169_private *tp, int location, int val)
>>>>>> case RTL_GIGA_MAC_VER_31:
>>>>>> r8168dp_2_mdio_write(tp, location, val);
>>>>>> break;
>>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>>> r8168g_mdio_write(tp, location, val);
>>>>>> break;
>>>>>> default:
>>>>>> @@ -1154,7 +1161,7 @@ static int rtl_readphy(struct rtl8169_private *tp, int location)
>>>>>> case RTL_GIGA_MAC_VER_28:
>>>>>> case RTL_GIGA_MAC_VER_31:
>>>>>> return r8168dp_2_mdio_read(tp, location);
>>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>>> return r8168g_mdio_read(tp, location);
>>>>>> default:
>>>>>> return r8169_mdio_read(tp, location);
>>>>>> @@ -1507,7 +1514,7 @@ static void __rtl8169_set_wol(struct rtl8169_private *tp, u32 wolopts)
>>>>>> break;
>>>>>> case RTL_GIGA_MAC_VER_34:
>>>>>> case RTL_GIGA_MAC_VER_37:
>>>>>> - case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_39 ... RTL_GIGA_MAC_VER_65:
>>>>>> if (wolopts)
>>>>>> rtl_mod_config2(tp, 0, PME_SIGNAL);
>>>>>> else
>>>>>> @@ -2073,6 +2080,9 @@ static enum mac_version rtl8169_get_mac_version(u16 xid, bool gmii)
>>>>>> u16 val;
>>>>>> enum mac_version ver;
>>>>>> } mac_info[] = {
>>>>>> + /* 8126A family. */
>>>>>> + { 0x7cf, 0x649, RTL_GIGA_MAC_VER_65 },
>>>>>> +
>>>>>> /* 8125B family. */
>>>>>> { 0x7cf, 0x641, RTL_GIGA_MAC_VER_63 },
>>>>>> @@ -2343,6 +2353,7 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
>>>>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
>>>>>> break;
>>>>>> case RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>>> RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
>>>>>> RX_PAUSE_SLOT_ON);
>>>>>> break;
>>>>>> @@ -2772,7 +2783,7 @@ static void rtl_enable_exit_l1(struct rtl8169_private *tp)
>>>>>> case RTL_GIGA_MAC_VER_37 ... RTL_GIGA_MAC_VER_38:
>>>>>> rtl_eri_set_bits(tp, 0xd4, 0x0c00);
>>>>>> break;
>>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0, 0x1f80);
>>>>>> break;
>>>>>> default:
>>>>>> @@ -2786,7 +2797,7 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>>>>> case RTL_GIGA_MAC_VER_34 ... RTL_GIGA_MAC_VER_38:
>>>>>> rtl_eri_clear_bits(tp, 0xd4, 0x1f00);
>>>>>> break;
>>>>>> - case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_65:
>>>>>> r8168_mac_ocp_modify(tp, 0xc0ac, 0x1f80, 0);
>>>>>> break;
>>>>>> default:
>>>>>> @@ -2796,6 +2807,8 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>>>>>> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>>>> {
>>>>>> + u8 val8;
>>>>>> +
>>>>>> if (tp->mac_version < RTL_GIGA_MAC_VER_32)
>>>>>> return;
>>>>>> @@ -2809,11 +2822,19 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>>>> return;
>>>>>> rtl_mod_config5(tp, 0, ASPM_en);
>>>>>> - rtl_mod_config2(tp, 0, ClkReqEn);
>>>>>> + switch (tp->mac_version) {
>>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>>> + val8 = RTL_R8(tp, INT_CFG0_8125) | INT_CFG0_CLKREQEN;
>>>>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>>>>> + break;
>>>>>> + default:
>>>>>> + rtl_mod_config2(tp, 0, ClkReqEn);
>>>>>> + break;
>>>>>> + }
>>>>>> switch (tp->mac_version) {
>>>>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>>>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>>>>> /* reset ephy tx/rx disable timer */
>>>>>> r8168_mac_ocp_modify(tp, 0xe094, 0xff00, 0);
>>>>>> /* chip can trigger L1.2 */
>>>>>> @@ -2825,14 +2846,22 @@ static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>>>>>> } else {
>>>>>> switch (tp->mac_version) {
>>>>>> case RTL_GIGA_MAC_VER_46 ... RTL_GIGA_MAC_VER_48:
>>>>>> - case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_65:
>>>>>> r8168_mac_ocp_modify(tp, 0xe092, 0x00ff, 0);
>>>>>> break;
>>>>>> default:
>>>>>> break;
>>>>>> }
>>>>>> - rtl_mod_config2(tp, ClkReqEn, 0);
>>>>>> + switch (tp->mac_version) {
>>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>>> + val8 = RTL_R8(tp, INT_CFG0_8125) & ~INT_CFG0_CLKREQEN;
>>>>>> + RTL_W8(tp, INT_CFG0_8125, val8);
>>>>>> + break;
>>>>>> + default:
>>>>>> + rtl_mod_config2(tp, ClkReqEn, 0);
>>>>>> + break;
>>>>>> + }
>>>>>> rtl_mod_config5(tp, ASPM_en, 0);
>>>>>> }
>>>>>> }
>>>>>> @@ -3545,10 +3574,15 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>>>> /* disable new tx descriptor format */
>>>>>> r8168_mac_ocp_modify(tp, 0xeb58, 0x0001, 0x0000);
>>>>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>>>> + RTL_W8(tp, 0xD8, RTL_R8(tp, 0xD8) & ~0x02);
>>>>>> +
>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>>>>> + else if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>>> r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0200);
>>>>>> else
>>>>>> - r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0400);
>>>>>> + r8168_mac_ocp_modify(tp, 0xe614, 0x0700, 0x0300);
>>>>>> if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>>> r8168_mac_ocp_modify(tp, 0xe63e, 0x0c30, 0x0000);
>>>>>> @@ -3561,6 +3595,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>>>> r8168_mac_ocp_modify(tp, 0xe056, 0x00f0, 0x0030);
>>>>>> r8168_mac_ocp_modify(tp, 0xe040, 0x1000, 0x0000);
>>>>>> r8168_mac_ocp_modify(tp, 0xea1c, 0x0003, 0x0001);
>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_65)
>>>>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0300, 0x0000);
>>>>>> + else
>>>>>> + r8168_mac_ocp_modify(tp, 0xea1c, 0x0004, 0x0000);
>>>>>> r8168_mac_ocp_modify(tp, 0xe0c0, 0x4f0f, 0x4403);
>>>>>> r8168_mac_ocp_modify(tp, 0xe052, 0x0080, 0x0068);
>>>>>> r8168_mac_ocp_modify(tp, 0xd430, 0x0fff, 0x047f);
>>>>>> @@ -3575,10 +3613,10 @@ static void rtl_hw_start_8125_common(struct rtl8169_private *tp)
>>>>>> rtl_loop_wait_low(tp, &rtl_mac_ocp_e00e_cond, 1000, 10);
>>>>>> - if (tp->mac_version == RTL_GIGA_MAC_VER_63)
>>>>>> - rtl8125b_config_eee_mac(tp);
>>>>>> - else
>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_61)
>>>>>> rtl8125a_config_eee_mac(tp);
>>>>>> + else
>>>>>> + rtl8125b_config_eee_mac(tp);
>>>>>> rtl_disable_rxdvgate(tp);
>>>>>> }
>>>>>> @@ -3622,6 +3660,12 @@ static void rtl_hw_start_8125b(struct rtl8169_private *tp)
>>>>>> rtl_hw_start_8125_common(tp);
>>>>>> }
>>>>>> +static void rtl_hw_start_8126a(struct rtl8169_private *tp)
>>>>>> +{
>>>>>> + rtl_set_def_aspm_entry_latency(tp);
>>>>>> + rtl_hw_start_8125_common(tp);
>>>>>> +}
>>>>>> +
>>>>>> static void rtl_hw_config(struct rtl8169_private *tp)
>>>>>> {
>>>>>> static const rtl_generic_fct hw_configs[] = {
>>>>>> @@ -3664,6 +3708,7 @@ static void rtl_hw_config(struct rtl8169_private *tp)
>>>>>> [RTL_GIGA_MAC_VER_53] = rtl_hw_start_8117,
>>>>>> [RTL_GIGA_MAC_VER_61] = rtl_hw_start_8125a_2,
>>>>>> [RTL_GIGA_MAC_VER_63] = rtl_hw_start_8125b,
>>>>>> + [RTL_GIGA_MAC_VER_65] = rtl_hw_start_8126a,
>>>>>> };
>>>>>> if (hw_configs[tp->mac_version])
>>>>>> @@ -3674,9 +3719,23 @@ static void rtl_hw_start_8125(struct rtl8169_private *tp)
>>>>>> {
>>>>>> int i;
>>>>>> + RTL_W8(tp, INT_CFG0_8125, 0x00);
>>>>>> +
>>>>>> /* disable interrupt coalescing */
>>>>>> - for (i = 0xa00; i < 0xb00; i += 4)
>>>>>> - RTL_W32(tp, i, 0);
>>>>>> + switch (tp->mac_version) {
>>>>>> + case RTL_GIGA_MAC_VER_61:
>>>>>> + for (i = 0xa00; i < 0xb00; i += 4)
>>>>>> + RTL_W32(tp, i, 0);
>>>>>> + break;
>>>>>> + case RTL_GIGA_MAC_VER_63:
>>>>>> + case RTL_GIGA_MAC_VER_65:
>>>>>> + for (i = 0xa00; i < 0xa80; i += 4)
>>>>>> + RTL_W32(tp, i, 0);
>>>>>> + RTL_W16(tp, INT_CFG1_8125, 0x0000);
>>>>>> + break;
>>>>>> + default:
>>>>>> + break;
>>>>>> + }
>>>>>> rtl_hw_config(tp);
>>>>>> }
>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>>> index b50f16786..badf78f81 100644
>>>>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>>> @@ -1152,6 +1152,7 @@ void r8169_hw_phy_config(struct rtl8169_private *tp, struct phy_device *phydev,
>>>>>> [RTL_GIGA_MAC_VER_53] = rtl8117_hw_phy_config,
>>>>>> [RTL_GIGA_MAC_VER_61] = rtl8125a_2_hw_phy_config,
>>>>>> [RTL_GIGA_MAC_VER_63] = rtl8125b_hw_phy_config,
>>>>>> + [RTL_GIGA_MAC_VER_65] = NULL,
>>>>>> };
>>>>>> if (phy_configs[ver])
>>>> The followoing adds support for the integrated PHY.
>>>> Please apply it on-top and re-test.
>>>>
>>>> ---
>>>> drivers/net/phy/realtek.c | 10 ++++++++++
>>>> 1 file changed, 10 insertions(+)
>>>>
>>>> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
>>>> index 894172a3e..132784321 100644
>>>> --- a/drivers/net/phy/realtek.c
>>>> +++ b/drivers/net/phy/realtek.c
>>>> @@ -1047,6 +1047,16 @@ static struct phy_driver realtek_drvs[] = {
>>>> .resume = rtlgen_resume,
>>>> .read_page = rtl821x_read_page,
>>>> .write_page = rtl821x_write_page,
>>>> + }, {
>>>> + PHY_ID_MATCH_EXACT(0x001cc862),
>>>> + .name = "RTL8251B 5Gbps PHY",
>>>> + .get_features = rtl822x_get_features,
>>>> + .config_aneg = rtl822x_config_aneg,
>>>> + .read_status = rtl822x_read_status,
>>>> + .suspend = genphy_suspend,
>>>> + .resume = rtlgen_resume,
>>>> + .read_page = rtl821x_read_page,
>>>> + .write_page = rtl821x_write_page,
>>>> }, {
>>>> PHY_ID_MATCH_EXACT(0x001cc961),
>>>> .name = "RTL8366RB Gigabit Ethernet",
>>> Thank you !
>>>
>>> I forward your 2nd patch to the openSUSE people I have been working and they prepared a new test kernel 6.7.2 with both patches for for me to test.
>>>
>>> I just installed the test kernel provided with both patches.
>>>
>>> Here is the dmesg | grep 8169 output using this new test kernel
>>>
>>> [ 3.630222] r8169 0000:05:00.0: enabling device (0000 -> 0003)
>>> [ 3.632148] r8169 0000:05:00.0 eth0: RTL8126A, e8:9c:25:78:c9:bf, XID 649, IRQ 207
>>> [ 3.632150] r8169 0000:05:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
>>> [ 3.633218] r8169 0000:05:00.0 enp5s0: renamed from eth0
>>> [ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
>>> [ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
>>> [ 4.236119] RTL8251B 5Gbps PHY r8169-0-500:00: attached PHY driver (mii_bus:phy_addr=r8169-0-500:00, irq=MAC)
>>> [ 4.349625] r8169 0000:05:00.0 enp5s0: Link is Down
>>> [ 7.858055] r8169 0000:05:00.0 enp5s0: Link is Up - 1Gbps/Full - flow control rx/tx
>>>
>>> Although dmesg has these 2 error messages, I have network connectivity, ran a quick speed test and am getting the correct speeds.
>>>
>> Thanks for the feedback. The firmware-related errors are expected, Realtek didn't provide the
>> firmware file to linux-firmware yet. I contacted Realtek in this matter.
>> Based on the experimental patches I'll prepare support for RTL8126A, and it should show up
>> in kernel version 6.9.
>
> THANK YOU for all your efforts they are greatly appreciated !
>
> I remember you mentioned about not having the firmware from Realtek but wasn't sure if the errors might mean I would run into issues.
>
RTL NIC firmware typically isn't something executable, but a collection of tuning parameters
to deal with compatibility issues. So it may or may not work on your system.
> So far everything has been working fine all day.
>
> Thanks for contacting Realtek about the firmware.
>
> You mentioned support showing up in the 6.9 kernel. Was that correct or did you mean 6.8 which comes out in March ?
>
6.8 is already in rc phase and closed for new features.
>>> [ 4.212381] r8169 0000:05:00.0: Direct firmware load for rtl_nic/rtl8126a-2.fw failed with error -2
>>> [ 4.212384] r8169 0000:05:00.0: Unable to load firmware rtl_nic/rtl8126a-2.fw (-2)
>>>
>>> Here is the 'lsmod | grep 8169' results so you can see what is loaded
>>>
>>> r8169 114688 0 mdio_devres 12288 1 r8169 libphy 245760 3 r8169,mdio_devres,realtek I will continue to test and report back if there are any network issues.
>>>
>> Please do so. Thank you
>>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-02-01 7:09 ` Heiner Kallweit
@ 2024-02-01 7:19 ` Takashi Iwai
2024-02-09 22:01 ` Heiner Kallweit
0 siblings, 1 reply; 10+ messages in thread
From: Takashi Iwai @ 2024-02-01 7:19 UTC (permalink / raw)
To: Heiner Kallweit; +Cc: Joe Salmeri, netdev@vger.kernel.org, tiwai
On Thu, 01 Feb 2024 08:09:21 +0100,
Heiner Kallweit wrote:
>
> On 01.02.2024 00:36, Joe Salmeri wrote:
> > You mentioned support showing up in the 6.9 kernel. Was that correct or did you mean 6.8 which comes out in March ?
> >
> 6.8 is already in rc phase and closed for new features.
As those are rather trivial changes, I can backport the stuff to
openSUSE Tumbleweed kernel if the changes are accepted by the
subsystem.
Heiner, did you already submit the patch for r8169, too?
I couldn't find it, only I saw a realtek phy patch in
https://lore.kernel.org/netdev/0c8e67ea-6505-43d1-bd51-94e7ecd6e222@gmail.com
thanks,
Takashi
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-02-01 7:19 ` Takashi Iwai
@ 2024-02-09 22:01 ` Heiner Kallweit
2024-02-10 8:11 ` Takashi Iwai
0 siblings, 1 reply; 10+ messages in thread
From: Heiner Kallweit @ 2024-02-09 22:01 UTC (permalink / raw)
To: Takashi Iwai; +Cc: Joe Salmeri, netdev@vger.kernel.org, tiwai
On 01.02.2024 08:19, Takashi Iwai wrote:
> On Thu, 01 Feb 2024 08:09:21 +0100,
> Heiner Kallweit wrote:
>>
>> On 01.02.2024 00:36, Joe Salmeri wrote:
>>> You mentioned support showing up in the 6.9 kernel. Was that correct or did you mean 6.8 which comes out in March ?
>>>
>> 6.8 is already in rc phase and closed for new features.
>
> As those are rather trivial changes, I can backport the stuff to
> openSUSE Tumbleweed kernel if the changes are accepted by the
> subsystem.
>
> Heiner, did you already submit the patch for r8169, too?
> I couldn't find it, only I saw a realtek phy patch in
> https://lore.kernel.org/netdev/0c8e67ea-6505-43d1-bd51-94e7ecd6e222@gmail.com
>
Meanwhile all relevant patches for RTL8126A support have been applied and are
available in linux-next.
net: phy: realtek: add 5Gbps support to rtl822x_config_aneg()
net: phy: realtek: use generic MDIO constants
net: mdio: add 2.5g and 5g related PMA speed constants
net: phy: realtek: add support for RTL8126A-integrated 5Gbps PHY
r8169: add support for RTL8126A
>
> thanks,
>
> Takashi
Heiner
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter
2024-02-09 22:01 ` Heiner Kallweit
@ 2024-02-10 8:11 ` Takashi Iwai
0 siblings, 0 replies; 10+ messages in thread
From: Takashi Iwai @ 2024-02-10 8:11 UTC (permalink / raw)
To: Heiner Kallweit; +Cc: Takashi Iwai, Joe Salmeri, netdev@vger.kernel.org, tiwai
On Fri, 09 Feb 2024 23:01:27 +0100,
Heiner Kallweit wrote:
>
> On 01.02.2024 08:19, Takashi Iwai wrote:
> > On Thu, 01 Feb 2024 08:09:21 +0100,
> > Heiner Kallweit wrote:
> >>
> >> On 01.02.2024 00:36, Joe Salmeri wrote:
> >>> You mentioned support showing up in the 6.9 kernel. Was that correct or did you mean 6.8 which comes out in March ?
> >>>
> >> 6.8 is already in rc phase and closed for new features.
> >
> > As those are rather trivial changes, I can backport the stuff to
> > openSUSE Tumbleweed kernel if the changes are accepted by the
> > subsystem.
> >
> > Heiner, did you already submit the patch for r8169, too?
> > I couldn't find it, only I saw a realtek phy patch in
> > https://lore.kernel.org/netdev/0c8e67ea-6505-43d1-bd51-94e7ecd6e222@gmail.com
> >
> Meanwhile all relevant patches for RTL8126A support have been applied and are
> available in linux-next.
>
> net: phy: realtek: add 5Gbps support to rtl822x_config_aneg()
> net: phy: realtek: use generic MDIO constants
> net: mdio: add 2.5g and 5g related PMA speed constants
> net: phy: realtek: add support for RTL8126A-integrated 5Gbps PHY
>
> r8169: add support for RTL8126A
Awesome, thanks!
Takashi
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2024-02-10 8:11 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <ab516cfd-24e8-4761-93a3-49f96a4e6b8f@gmail.com>
2024-01-29 22:19 ` Kernel Module r8169 and the Realtek 8126 PCIe 5 G/bps WIRED ethernet adapter Heiner Kallweit
[not found] <edabbc1f-5440-4170-83a4-f436a6d04f76@gmail.com>
2024-01-30 16:34 ` Joe Salmeri
2024-01-30 19:59 ` Heiner Kallweit
2024-01-31 16:14 ` Joe Salmeri
2024-01-31 20:40 ` Heiner Kallweit
2024-01-31 23:36 ` Joe Salmeri
2024-02-01 7:09 ` Heiner Kallweit
2024-02-01 7:19 ` Takashi Iwai
2024-02-09 22:01 ` Heiner Kallweit
2024-02-10 8:11 ` Takashi Iwai
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).