From: Jacopo Mondi <jacopo@jmondi.org>
To: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>,
tomi.valkeinen@ideasonboard.com, sakari.ailus@linux.intel.com,
niklas.soderlund@ragnatech.se, kieran.bingham@ideasonboard.com,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Hans Verkuil <hverkuil-cisco@xs4all.nl>,
linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v4 3/6] media: max9286: Use enabled routes to calculate pixelrate
Date: Fri, 17 Dec 2021 14:32:55 +0100 [thread overview]
Message-ID: <20211217133255.fodyj5dgluga3dr6@uno.localdomain> (raw)
In-Reply-To: <Ybv2HilpOKyP/wE4@pendragon.ideasonboard.com>
Hi Laurent,
On Fri, Dec 17, 2021 at 04:29:50AM +0200, Laurent Pinchart wrote:
> Hi Jacopo,
>
> Thank you for the patch.
>
> On Thu, Dec 16, 2021 at 06:47:43PM +0100, Jacopo Mondi wrote:
> > Now that the device supports routing, use the enabled routes instead
> > of the connected sources to compute the output pixel rate.
> >
> > To do so, update the route_mask after a set_routing() call with the
> > ACTIVE format, and re-calculate the pixel rate just after.
> >
> > At the same time, start and stop only the enabled routes at s_stream()
> > time.
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> > ---
> > drivers/media/i2c/max9286.c | 63 ++++++++++++++++++++++++++++++-------
> > 1 file changed, 51 insertions(+), 12 deletions(-)
> >
> > diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
> > index eb76acdb2cd9..1395eb783dc0 100644
> > --- a/drivers/media/i2c/max9286.c
> > +++ b/drivers/media/i2c/max9286.c
> > @@ -188,8 +188,11 @@ struct max9286_priv {
> > struct v4l2_async_notifier notifier;
> > };
> >
> > +#define to_index(priv, source) ((source) - &(priv)->sources[0])
> > +
> > static struct max9286_source *next_source(struct max9286_priv *priv,
> > - struct max9286_source *source)
> > + struct max9286_source *source,
> > + bool routed)
> > {
> > if (!source)
> > source = &priv->sources[0];
> > @@ -197,17 +200,27 @@ static struct max9286_source *next_source(struct max9286_priv *priv,
> > source++;
> >
> > for (; source < &priv->sources[MAX9286_NUM_GMSL]; source++) {
> > - if (source->fwnode)
> > + unsigned int index = to_index(priv, source);
> > +
> > + if (!source->fwnode)
> > + continue;
> > +
> > + /*
> > + * Careful here! A very unfortunate call to set_routing() can
> > + * change priv->route_mask behind our back!
> > + */
>
> This seems error-prone. I wonder if we could instead remove route_mask
> completely, and compute it as .s_stream(1) time by walking the routes
> from the state. That would avoid storing state information in
> max9286_priv.
I wish I could, but I need an up-to-date pixelrate for the CSI-2
receiver, before it calls into s_stream(1) :(
The race window is very small (I know, if things can go wrong, they
will..) and I could protect it with a mutex ?
>
> The downside is that we'll have to pass the route mask down to functions
> called by max9286_s_stream(). At some point in the future, I'd like to
> see support for subclassing the subdev state in subdev drivers, at which
> point we will be able to cache the route_mask in the subclassed state
> when configuring routing, and reusing the cached value when starting the
> streams.
>
With the state being locked, this would prevent any race from
happening, that's right!
What about a mutex for the time being ?
> > + if (!routed || priv->route_mask & BIT(index))
> > return source;
> > }
> >
> > return NULL;
> > }
> >
> > -#define for_each_source(priv, source) \
> > - for ((source) = NULL; ((source) = next_source((priv), (source))); )
> > +#define for_each_route(priv, source) \
> > + for ((source) = NULL; ((source) = next_source((priv), (source), true)); )
> >
> > -#define to_index(priv, source) ((source) - &(priv)->sources[0])
> > +#define for_each_source(priv, source) \
> > + for ((source) = NULL; ((source) = next_source((priv), (source), false)); )
> >
> > static inline struct max9286_priv *sd_to_max9286(struct v4l2_subdev *sd)
> > {
> > @@ -409,7 +422,7 @@ static int max9286_check_video_links(struct max9286_priv *priv)
> > if (ret < 0)
> > return -EIO;
> >
> > - if ((ret & MAX9286_VIDEO_DETECT_MASK) == priv->source_mask)
> > + if ((ret & MAX9286_VIDEO_DETECT_MASK) == priv->route_mask)
> > break;
> >
> > usleep_range(350, 500);
> > @@ -493,9 +506,10 @@ static int max9286_check_config_link(struct max9286_priv *priv,
> > static int max9286_set_pixelrate(struct max9286_priv *priv)
> > {
> > struct max9286_source *source = NULL;
> > + unsigned int num_routes = 0;
> > u64 pixelrate = 0;
> >
> > - for_each_source(priv, source) {
> > + for_each_route(priv, source) {
> > struct v4l2_ctrl *ctrl;
> > u64 source_rate = 0;
> >
> > @@ -516,6 +530,8 @@ static int max9286_set_pixelrate(struct max9286_priv *priv)
> > "Unable to calculate pixel rate\n");
> > return -EINVAL;
> > }
> > +
> > + num_routes++;
> > }
> >
> > if (!pixelrate) {
> > @@ -529,7 +545,7 @@ static int max9286_set_pixelrate(struct max9286_priv *priv)
> > * by the number of available sources.
> > */
> > return v4l2_ctrl_s_ctrl_int64(priv->pixelrate,
> > - pixelrate * priv->nsources);
> > + pixelrate * num_routes);
> > }
> >
> > static int max9286_notify_bound(struct v4l2_async_notifier *notifier,
> > @@ -691,8 +707,8 @@ static int max9286_s_stream(struct v4l2_subdev *sd, int enable)
> > */
> > max9286_i2c_mux_open(priv);
> >
> > - /* Start all cameras. */
> > - for_each_source(priv, source) {
> > + /* Start cameras. */
> > + for_each_route(priv, source) {
> > ret = v4l2_subdev_call(source->sd, video, s_stream, 1);
> > if (ret)
> > return ret;
> > @@ -733,8 +749,8 @@ static int max9286_s_stream(struct v4l2_subdev *sd, int enable)
> > } else {
> > max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV);
> >
> > - /* Stop all cameras. */
> > - for_each_source(priv, source)
> > + /* Stop cameras. */
> > + for_each_route(priv, source)
> > v4l2_subdev_call(source->sd, video, s_stream, 0);
> >
> > max9286_i2c_mux_close(priv);
> > @@ -912,6 +928,29 @@ static int max9286_set_routing(struct v4l2_subdev *sd,
> > v4l2_subdev_lock_state(state);
> >
> > ret = _max9286_set_routing(sd, state, routing);
> > + if (ret)
> > + goto out;
> > +
> > + if (which == V4L2_SUBDEV_FORMAT_TRY)
> > + goto out;
> > +
> > + /*
> > + * Update the active routes mask and the pixel rate according to the
> > + * routed sources.
> > + */
> > + priv->route_mask = 0;
> > + for (i = 0; i < routing->num_routes; ++i) {
> > + struct v4l2_subdev_route *route = &routing->routes[i];
> > +
> > + if (!(route->flags & V4L2_SUBDEV_ROUTE_FL_ACTIVE))
> > + continue;
> > +
> > + priv->route_mask |= BIT(route->sink_pad);
> > + }
> > +
> > + max9286_set_pixelrate(priv);
> > +
> > +out:
> > v4l2_subdev_unlock_state(state);
> >
> > return ret;
>
> --
> Regards,
>
> Laurent Pinchart
next prev parent reply other threads:[~2021-12-17 13:32 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-16 17:47 [PATCH v4 0/6] media: max9286: Add multiplexed streams support Jacopo Mondi
2021-12-16 17:47 ` [PATCH v4 1/6] media: max9286: Add support for v4l2_subdev_state Jacopo Mondi
2021-12-16 18:33 ` Laurent Pinchart
2021-12-16 17:47 ` [PATCH v4 2/6] media: max9286: Implement set_routing Jacopo Mondi
2021-12-17 1:56 ` Laurent Pinchart
2021-12-17 2:18 ` Laurent Pinchart
2021-12-17 2:24 ` Laurent Pinchart
2021-12-17 13:28 ` Jacopo Mondi
2021-12-16 17:47 ` [PATCH v4 3/6] media: max9286: Use enabled routes to calculate pixelrate Jacopo Mondi
2021-12-17 2:29 ` Laurent Pinchart
2021-12-17 13:32 ` Jacopo Mondi [this message]
2021-12-16 17:47 ` [PATCH v4 4/6] media: max9286: Use routes to configure link order Jacopo Mondi
2021-12-17 2:35 ` Laurent Pinchart
2021-12-17 13:38 ` Jacopo Mondi
2021-12-16 17:47 ` [PATCH v4 5/6] media: max9286: Move format to subdev state Jacopo Mondi
2021-12-17 2:40 ` Laurent Pinchart
2021-12-17 3:09 ` Laurent Pinchart
2021-12-17 14:11 ` Jacopo Mondi
2024-05-09 13:11 ` Laurent Pinchart
2021-12-16 17:47 ` [PATCH v4 6/6] media: max9286: Implement get_frame_desc() Jacopo Mondi
2021-12-17 2:45 ` Laurent Pinchart
2021-12-17 14:12 ` Jacopo Mondi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211217133255.fodyj5dgluga3dr6@uno.localdomain \
--to=jacopo@jmondi.org \
--cc=hverkuil-cisco@xs4all.nl \
--cc=jacopo+renesas@jmondi.org \
--cc=kieran.bingham@ideasonboard.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=niklas.soderlund@ragnatech.se \
--cc=sakari.ailus@linux.intel.com \
--cc=tomi.valkeinen@ideasonboard.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).