* [PATCH v6 0/3] Add support for nuvoton ma35d1 pin control
@ 2024-03-13 3:57 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
From: Jacky Huang <ychuang3@nuvoton.com>
This patch series adds the pin control and GPIO driver for the nuvoton ma35d1
ARMv8 SoC. It includes DT binding documentation and the ma35d1 pin control driver.
This pin control driver has been tested on the ma35d1 som board with Linux 6.8-rc5 .
v6:
- Remove DTS from this patchset. The DTS will be submitted in another patchset.
v5:
- Update the pinctrl driver header file pinctrl-ma35.h
- Include platform_device.h to fix compile issues.
v4:
- Update the pinctrl driver Kconfig
- Add depends to CONFIG_PINCTRL_MA35D1 to prevent compilation errors.
- Update the pinctrl driver
- Utilize devm_kcalloc() instead of devm_kzalloc().
- Employ ARRAY_SIZE() instead of sizeof()/sizeof().
v3:
- Update DTS and YAML files
- Corrected the unit address of nodes gpioa ~ gpion.
- Removed the invalid "pin-default" node.
- Removed the phandle entry from "nuvoton,pins".
- Update pinctrl driver
- Fixed the Kconfig by using "depend on" instead of "if".
- Removed unused #include of header files.
- Utilized immutable irq_chip instead of dynamic irq_chip.
- Replaced ma35_dt_free_map() with pinconf_generic_dt_free_map().
- Implemented other minor fixes as suggested by the reviewer.
v2:
- Update nuvoton,ma35d1-pinctrl.yaml
- Update the 'nuvoton,pins' to follow the style of rockchip pinctrl approch.
- Use power-source to indicate the pin voltage selection which follow the
realtek pinctrl approch.
- Instead of integer, use drive-strength-microamp to specify the real driving
strength capability of IO pins.
- Update ma35d1 pinctrl driver
- Add I/O drive strength lookup table for translating device tree setting
into control register.
- Remove ma35d1-pinfunc.h which is unused after update definition of 'nuvoton,pins'.
Jacky Huang (3):
dt-bindings: reset: Add syscon to nuvoton ma35d1 system-management
node
dt-bindings: pinctrl: Document nuvoton ma35d1 pin control
pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
.../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++
.../bindings/reset/nuvoton,ma35d1-reset.yaml | 3 +-
drivers/pinctrl/nuvoton/Kconfig | 19 +
drivers/pinctrl/nuvoton/Makefile | 2 +
drivers/pinctrl/nuvoton/pinctrl-ma35.c | 1211 +++++++++++
drivers/pinctrl/nuvoton/pinctrl-ma35.h | 51 +
drivers/pinctrl/nuvoton/pinctrl-ma35d1.c | 1797 +++++++++++++++++
7 files changed, 3245 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.c
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.h
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
--
2.34.1
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v6 0/3] Add support for nuvoton ma35d1 pin control
@ 2024-03-13 3:57 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
From: Jacky Huang <ychuang3@nuvoton.com>
This patch series adds the pin control and GPIO driver for the nuvoton ma35d1
ARMv8 SoC. It includes DT binding documentation and the ma35d1 pin control driver.
This pin control driver has been tested on the ma35d1 som board with Linux 6.8-rc5 .
v6:
- Remove DTS from this patchset. The DTS will be submitted in another patchset.
v5:
- Update the pinctrl driver header file pinctrl-ma35.h
- Include platform_device.h to fix compile issues.
v4:
- Update the pinctrl driver Kconfig
- Add depends to CONFIG_PINCTRL_MA35D1 to prevent compilation errors.
- Update the pinctrl driver
- Utilize devm_kcalloc() instead of devm_kzalloc().
- Employ ARRAY_SIZE() instead of sizeof()/sizeof().
v3:
- Update DTS and YAML files
- Corrected the unit address of nodes gpioa ~ gpion.
- Removed the invalid "pin-default" node.
- Removed the phandle entry from "nuvoton,pins".
- Update pinctrl driver
- Fixed the Kconfig by using "depend on" instead of "if".
- Removed unused #include of header files.
- Utilized immutable irq_chip instead of dynamic irq_chip.
- Replaced ma35_dt_free_map() with pinconf_generic_dt_free_map().
- Implemented other minor fixes as suggested by the reviewer.
v2:
- Update nuvoton,ma35d1-pinctrl.yaml
- Update the 'nuvoton,pins' to follow the style of rockchip pinctrl approch.
- Use power-source to indicate the pin voltage selection which follow the
realtek pinctrl approch.
- Instead of integer, use drive-strength-microamp to specify the real driving
strength capability of IO pins.
- Update ma35d1 pinctrl driver
- Add I/O drive strength lookup table for translating device tree setting
into control register.
- Remove ma35d1-pinfunc.h which is unused after update definition of 'nuvoton,pins'.
Jacky Huang (3):
dt-bindings: reset: Add syscon to nuvoton ma35d1 system-management
node
dt-bindings: pinctrl: Document nuvoton ma35d1 pin control
pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
.../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++
.../bindings/reset/nuvoton,ma35d1-reset.yaml | 3 +-
drivers/pinctrl/nuvoton/Kconfig | 19 +
drivers/pinctrl/nuvoton/Makefile | 2 +
drivers/pinctrl/nuvoton/pinctrl-ma35.c | 1211 +++++++++++
drivers/pinctrl/nuvoton/pinctrl-ma35.h | 51 +
drivers/pinctrl/nuvoton/pinctrl-ma35d1.c | 1797 +++++++++++++++++
7 files changed, 3245 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.c
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.h
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v6 1/3] dt-bindings: reset: Add syscon to nuvoton ma35d1 system-management node
2024-03-13 3:57 ` Jacky Huang
@ 2024-03-13 3:57 ` Jacky Huang
-1 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung, Krzysztof Kozlowski
From: Jacky Huang <ychuang3@nuvoton.com>
Add a compatible 'syscon' to the system management node since the system
control registers are mapped by this driver. The other driver must access
the system control registers through 'regmap' using a phandle that
references this node.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
---
.../devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml b/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
index 34c5c1c08ec1..3ce7dcecd87a 100644
--- a/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
+++ b/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
@@ -18,6 +18,7 @@ properties:
compatible:
items:
- const: nuvoton,ma35d1-reset
+ - const: syscon
reg:
maxItems: 1
@@ -37,7 +38,7 @@ examples:
- |
system-management@40460000 {
- compatible = "nuvoton,ma35d1-reset";
+ compatible = "nuvoton,ma35d1-reset", "syscon";
reg = <0x40460000 0x200>;
#reset-cells = <1>;
};
--
2.34.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v6 1/3] dt-bindings: reset: Add syscon to nuvoton ma35d1 system-management node
@ 2024-03-13 3:57 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung, Krzysztof Kozlowski
From: Jacky Huang <ychuang3@nuvoton.com>
Add a compatible 'syscon' to the system management node since the system
control registers are mapped by this driver. The other driver must access
the system control registers through 'regmap' using a phandle that
references this node.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
---
.../devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml b/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
index 34c5c1c08ec1..3ce7dcecd87a 100644
--- a/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
+++ b/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
@@ -18,6 +18,7 @@ properties:
compatible:
items:
- const: nuvoton,ma35d1-reset
+ - const: syscon
reg:
maxItems: 1
@@ -37,7 +38,7 @@ examples:
- |
system-management@40460000 {
- compatible = "nuvoton,ma35d1-reset";
+ compatible = "nuvoton,ma35d1-reset", "syscon";
reg = <0x40460000 0x200>;
#reset-cells = <1>;
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v6 2/3] dt-bindings: pinctrl: Document nuvoton ma35d1 pin control
2024-03-13 3:57 ` Jacky Huang
@ 2024-03-13 3:57 ` Jacky Huang
-1 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung, Krzysztof Kozlowski
From: Jacky Huang <ychuang3@nuvoton.com>
Add documentation to describe nuvoton ma35d1 pin control and GPIO.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++++++++++++++++++
1 file changed, 163 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
new file mode 100644
index 000000000000..8b9ec263213f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton MA35D1 pin control and GPIO
+
+maintainers:
+ - Shan-Chun Hung <schung@nuvoton.com>
+ - Jacky Huang <ychuang3@nuvoton.com>
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+properties:
+ compatible:
+ enum:
+ - nuvoton,ma35d1-pinctrl
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 1
+
+ nuvoton,sys:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle of the system-management node.
+
+ ranges: true
+
+patternProperties:
+ "^gpio@[0-9a-f]+$":
+ type: object
+ additionalProperties: false
+ properties:
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupts:
+ description:
+ The interrupt outputs to sysirq.
+ maxItems: 1
+
+ required:
+ - gpio-controller
+ - '#gpio-cells'
+ - reg
+ - clocks
+ - interrupt-controller
+ - '#interrupt-cells'
+ - interrupts
+
+ "^pin-[a-z0-9]+$":
+ type: object
+ description:
+ A pinctrl node should contain at least one subnodes representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and input
+ schmitt.
+
+ $ref: pincfg-node.yaml#
+
+ properties:
+ power-source:
+ description: |
+ Valid arguments are described as below:
+ 0: power supply of 1.8V
+ 1: power supply of 3.3V
+ enum: [0, 1]
+
+ drive-strength-microamp:
+ oneOf:
+ - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
+ description: 1.8V I/O driving strength
+ - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
+ description: 3.3V I/O driving strength
+
+ unevaluatedProperties: false
+
+ "-grp$":
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ properties:
+ nuvoton,pins:
+ description:
+ Each entry consists of 4 parameters and represents the mux and config
+ setting for one pin.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ minItems: 1
+ items:
+ items:
+ - minimum: 0
+ maximum: 13
+ description:
+ Pin bank.
+ - minimum: 0
+ maximum: 15
+ description:
+ Pin bank index.
+ - minimum: 0
+ maximum: 15
+ description:
+ Mux 0 means GPIO and mux 1 to 15 means the specific device function.
+
+required:
+ - compatible
+ - nuvoton,sys
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
+
+ pinctrl@40040000 {
+ compatible = "nuvoton,ma35d1-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ nuvoton,sys = <&sys>;
+ ranges = <0 0x40040000 0xc00>;
+
+ gpio@0 {
+ reg = <0x0 0x40>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk GPA_GATE>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart-grp {
+ uart11-pins {
+ nuvoton,pins = <11 0 2>,
+ <11 1 2>,
+ <11 2 2>,
+ <11 3 2>;
+ bias-disable;
+ power-source = <1>;
+ };
+ };
+ };
--
2.34.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v6 2/3] dt-bindings: pinctrl: Document nuvoton ma35d1 pin control
@ 2024-03-13 3:57 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung, Krzysztof Kozlowski
From: Jacky Huang <ychuang3@nuvoton.com>
Add documentation to describe nuvoton ma35d1 pin control and GPIO.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++++++++++++++++++
1 file changed, 163 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
new file mode 100644
index 000000000000..8b9ec263213f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton MA35D1 pin control and GPIO
+
+maintainers:
+ - Shan-Chun Hung <schung@nuvoton.com>
+ - Jacky Huang <ychuang3@nuvoton.com>
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+properties:
+ compatible:
+ enum:
+ - nuvoton,ma35d1-pinctrl
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 1
+
+ nuvoton,sys:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle of the system-management node.
+
+ ranges: true
+
+patternProperties:
+ "^gpio@[0-9a-f]+$":
+ type: object
+ additionalProperties: false
+ properties:
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupts:
+ description:
+ The interrupt outputs to sysirq.
+ maxItems: 1
+
+ required:
+ - gpio-controller
+ - '#gpio-cells'
+ - reg
+ - clocks
+ - interrupt-controller
+ - '#interrupt-cells'
+ - interrupts
+
+ "^pin-[a-z0-9]+$":
+ type: object
+ description:
+ A pinctrl node should contain at least one subnodes representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and input
+ schmitt.
+
+ $ref: pincfg-node.yaml#
+
+ properties:
+ power-source:
+ description: |
+ Valid arguments are described as below:
+ 0: power supply of 1.8V
+ 1: power supply of 3.3V
+ enum: [0, 1]
+
+ drive-strength-microamp:
+ oneOf:
+ - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
+ description: 1.8V I/O driving strength
+ - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
+ description: 3.3V I/O driving strength
+
+ unevaluatedProperties: false
+
+ "-grp$":
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ properties:
+ nuvoton,pins:
+ description:
+ Each entry consists of 4 parameters and represents the mux and config
+ setting for one pin.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ minItems: 1
+ items:
+ items:
+ - minimum: 0
+ maximum: 13
+ description:
+ Pin bank.
+ - minimum: 0
+ maximum: 15
+ description:
+ Pin bank index.
+ - minimum: 0
+ maximum: 15
+ description:
+ Mux 0 means GPIO and mux 1 to 15 means the specific device function.
+
+required:
+ - compatible
+ - nuvoton,sys
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
+
+ pinctrl@40040000 {
+ compatible = "nuvoton,ma35d1-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ nuvoton,sys = <&sys>;
+ ranges = <0 0x40040000 0xc00>;
+
+ gpio@0 {
+ reg = <0x0 0x40>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk GPA_GATE>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart-grp {
+ uart11-pins {
+ nuvoton,pins = <11 0 2>,
+ <11 1 2>,
+ <11 2 2>,
+ <11 3 2>;
+ bias-disable;
+ power-source = <1>;
+ };
+ };
+ };
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
2024-03-13 3:57 ` Jacky Huang
@ 2024-03-13 3:57 ` Jacky Huang
-1 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
From: Jacky Huang <ychuang3@nuvoton.com>
Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
add support for ma35d1 pinctrl.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
---
drivers/pinctrl/nuvoton/Kconfig | 19 +
drivers/pinctrl/nuvoton/Makefile | 2 +
drivers/pinctrl/nuvoton/pinctrl-ma35.c | 1211 +++++++++++++++
drivers/pinctrl/nuvoton/pinctrl-ma35.h | 51 +
drivers/pinctrl/nuvoton/pinctrl-ma35d1.c | 1797 ++++++++++++++++++++++
5 files changed, 3080 insertions(+)
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.c
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.h
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
diff --git a/drivers/pinctrl/nuvoton/Kconfig b/drivers/pinctrl/nuvoton/Kconfig
index 2abbfcec1fae..7eadaaf48d6e 100644
--- a/drivers/pinctrl/nuvoton/Kconfig
+++ b/drivers/pinctrl/nuvoton/Kconfig
@@ -45,3 +45,22 @@ config PINCTRL_NPCM8XX
Say Y or M here to enable pin controller and GPIO support for
the Nuvoton NPCM8XX SoC. This is strongly recommended when
building a kernel that will run on this chip.
+
+config PINCTRL_MA35
+ bool
+ depends on (ARCH_MA35 || COMPILE_TEST) && OF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GENERIC_PINCONF
+ select GPIOLIB
+ select GPIO_GENERIC
+ select GPIOLIB_IRQCHIP
+ select MFD_SYSCON
+
+config PINCTRL_MA35D1
+ bool "Pinctrl and GPIO driver for Nuvoton MA35D1"
+ depends on (ARCH_MA35 || COMPILE_TEST) && OF
+ select PINCTRL_MA35
+ help
+ Say Y here to enable pin controller and GPIO support
+ for Nuvoton MA35D1 SoC.
diff --git a/drivers/pinctrl/nuvoton/Makefile b/drivers/pinctrl/nuvoton/Makefile
index 08031eab0af6..346c5082bc60 100644
--- a/drivers/pinctrl/nuvoton/Makefile
+++ b/drivers/pinctrl/nuvoton/Makefile
@@ -4,3 +4,5 @@
obj-$(CONFIG_PINCTRL_WPCM450) += pinctrl-wpcm450.o
obj-$(CONFIG_PINCTRL_NPCM7XX) += pinctrl-npcm7xx.o
obj-$(CONFIG_PINCTRL_NPCM8XX) += pinctrl-npcm8xx.o
+obj-$(CONFIG_PINCTRL_MA35) += pinctrl-ma35.o
+obj-$(CONFIG_PINCTRL_MA35D1) += pinctrl-ma35d1.o
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35.c b/drivers/pinctrl/nuvoton/pinctrl-ma35.c
new file mode 100644
index 000000000000..8efbe559be1e
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35.c
@@ -0,0 +1,1211 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <schung@nuvoton.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio/driver.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "../core.h"
+#include "../pinconf.h"
+#include "pinctrl-ma35.h"
+
+#define MA35_MFP_REG_BASE 0x80
+#define MA35_MFP_REG_SZ_PER_BANK 8
+#define MA35_MFP_BITS_PER_PORT 4
+
+#define MA35_GPIO_BANK_MAX 14
+#define MA35_GPIO_PORT_MAX 16
+
+/* GPIO control registers */
+#define MA35_GP_REG_MODE 0x00
+#define MA35_GP_REG_DINOFF 0x04
+#define MA35_GP_REG_DOUT 0x08
+#define MA35_GP_REG_DATMSK 0x0c
+#define MA35_GP_REG_PIN 0x10
+#define MA35_GP_REG_DBEN 0x14
+#define MA35_GP_REG_INTTYPE 0x18
+#define MA35_GP_REG_INTEN 0x1c
+#define MA35_GP_REG_INTSRC 0x20
+#define MA35_GP_REG_SMTEN 0x24
+#define MA35_GP_REG_SLEWCTL 0x28
+#define MA35_GP_REG_SPW 0x2c
+#define MA35_GP_REG_PUSEL 0x30
+#define MA35_GP_REG_DSL 0x38
+#define MA35_GP_REG_DSH 0x3c
+
+/* GPIO mode control */
+#define MA35_GP_MODE_INPUT 0x0
+#define MA35_GP_MODE_OUTPUT 0x1
+#define MA35_GP_MODE_OPEN_DRAIN 0x2
+#define MA35_GP_MODE_QUASI 0x3
+
+/* GPIO pull-up and pull-down selection control */
+#define MA35_GP_PUSEL_DISABLE 0x0
+#define MA35_GP_PUSEL_PULL_UP 0x1
+#define MA35_GP_PUSEL_PULL_DOWN 0x2
+
+/* Each pin data input/output is mapped by address mapping */
+#define MA35_PIN_MAP_BASE 0x800
+#define MA35_GP_DSH_BASE_PORT 8
+
+#define MVOLT_1800 0
+#define MVOLT_3300 1
+
+static const char * const gpio_group_name[] = {
+ "gpioa", "gpiob", "gpioc", "gpiod", "gpioe", "gpiof", "gpiog",
+ "gpioh", "gpioi", "gpioj", "gpiok", "gpiol", "gpiom", "gpion",
+};
+
+static const u32 ds_1800mv_tbl[] = {
+ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000,
+};
+
+static const u32 ds_3300mv_tbl[] = {
+ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000,
+};
+
+struct ma35_pin_func {
+ const char *name;
+ const char **groups;
+ u32 ngroups;
+};
+
+struct ma35_pin_setting {
+ u32 offset;
+ u32 shift;
+ u32 muxval;
+ unsigned long *configs;
+ unsigned int nconfigs;
+};
+
+struct ma35_pin_group {
+ const char *name;
+ unsigned int npins;
+ unsigned int *pins;
+ struct ma35_pin_setting *settings;
+};
+
+struct ma35_pin_bank {
+ void __iomem *reg_base;
+ struct clk *clk;
+ int irq;
+ u8 nr_pins;
+ const char *name;
+ u8 bank_num;
+ bool valid;
+ struct device_node *np;
+ struct gpio_chip chip;
+ u32 irqtype;
+ u32 irqinten;
+ struct regmap *regmap;
+ struct device *dev;
+ spinlock_t lock;
+};
+
+struct ma35_pin_ctrl {
+ struct ma35_pin_bank *pin_banks;
+ u32 nr_banks;
+ u32 nr_pins;
+};
+
+struct ma35_pinctrl {
+ struct device *dev;
+ struct ma35_pin_ctrl *ctrl;
+ struct pinctrl_dev *pctl;
+ const struct ma35_pinctrl_soc_info *info;
+ struct regmap *regmap;
+ struct ma35_pin_group *groups;
+ unsigned int ngroups;
+ struct ma35_pin_func *functions;
+ unsigned int nfunctions;
+};
+
+static int ma35_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->ngroups;
+}
+
+static const char *ma35_get_group_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->groups[selector].name;
+}
+
+static int ma35_get_group_pins(struct pinctrl_dev *pctldev, unsigned int selector,
+ const unsigned int **pins, unsigned int *npins)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ if (selector >= npctl->ngroups)
+ return -EINVAL;
+
+ *pins = npctl->groups[selector].pins;
+ *npins = npctl->groups[selector].npins;
+
+ return 0;
+}
+
+static struct ma35_pin_group *ma35_pinctrl_find_group_by_name(
+ const struct ma35_pinctrl *npctl, const char *name)
+{
+ int i;
+
+ for (i = 0; i < npctl->ngroups; i++) {
+ if (!strcmp(npctl->groups[i].name, name))
+ return &npctl->groups[i];
+ }
+ return NULL;
+}
+
+static int ma35_pinctrl_dt_node_to_map_func(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned int *num_maps)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ struct ma35_pin_group *grp;
+ struct pinctrl_map *new_map;
+ struct device_node *parent;
+ int map_num = 1;
+ int i;
+
+ /*
+ * first find the group of this node and check if we need create
+ * config maps for pins
+ */
+ grp = ma35_pinctrl_find_group_by_name(npctl, np->name);
+ if (!grp) {
+ dev_err(npctl->dev, "unable to find group for node %s\n", np->name);
+ return -EINVAL;
+ }
+
+ map_num += grp->npins;
+ new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map), GFP_KERNEL);
+ if (!new_map)
+ return -ENOMEM;
+
+ *map = new_map;
+ *num_maps = map_num;
+ /* create mux map */
+ parent = of_get_parent(np);
+ if (!parent) {
+ devm_kfree(pctldev->dev, new_map);
+ return -EINVAL;
+ }
+
+ new_map[0].type = PIN_MAP_TYPE_MUX_GROUP;
+ new_map[0].data.mux.function = parent->name;
+ new_map[0].data.mux.group = np->name;
+ of_node_put(parent);
+
+ new_map++;
+ for (i = 0; i < grp->npins; i++) {
+ new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN;
+ new_map[i].data.configs.group_or_pin = pin_get_name(pctldev, grp->pins[i]);
+ new_map[i].data.configs.configs = grp->settings[i].configs;
+ new_map[i].data.configs.num_configs = grp->settings[i].nconfigs;
+ }
+ dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
+ (*map)->data.mux.function, (*map)->data.mux.group, map_num);
+
+ return 0;
+}
+
+static const struct pinctrl_ops ma35_pctrl_ops = {
+ .get_groups_count = ma35_get_groups_count,
+ .get_group_name = ma35_get_group_name,
+ .get_group_pins = ma35_get_group_pins,
+ .dt_node_to_map = ma35_pinctrl_dt_node_to_map_func,
+ .dt_free_map = pinconf_generic_dt_free_map,
+};
+
+static int ma35_pinmux_get_func_count(struct pinctrl_dev *pctldev)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->nfunctions;
+}
+
+static const char *ma35_pinmux_get_func_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->functions[selector].name;
+}
+
+static int ma35_pinmux_get_func_groups(struct pinctrl_dev *pctldev,
+ unsigned int function,
+ const char *const **groups,
+ unsigned int *const num_groups)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = npctl->functions[function].groups;
+ *num_groups = npctl->functions[function].ngroups;
+
+ return 0;
+}
+
+static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
+ unsigned int group)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ struct ma35_pin_group *grp = &npctl->groups[group];
+ struct ma35_pin_setting *setting = grp->settings;
+ u32 i, regval;
+
+ dev_dbg(npctl->dev, "enable function %s group %s\n",
+ npctl->functions[selector].name, npctl->groups[group].name);
+
+ for (i = 0; i < grp->npins; i++) {
+ regmap_read(npctl->regmap, setting->offset, ®val);
+ regval &= ~GENMASK(setting->shift + 3, setting->shift);
+ regval |= setting->muxval << setting->shift;
+ regmap_write(npctl->regmap, setting->offset, regval);
+ setting++;
+ }
+ return 0;
+}
+
+static const struct pinmux_ops ma35_pmx_ops = {
+ .get_functions_count = ma35_pinmux_get_func_count,
+ .get_function_name = ma35_pinmux_get_func_name,
+ .get_function_groups = ma35_pinmux_get_func_groups,
+ .set_mux = ma35_pinmux_set_mux,
+ .strict = true,
+};
+
+static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
+ unsigned long flags;
+ unsigned int regval;
+
+ spin_lock_irqsave(&bank->lock, flags);
+
+ regval = readl(reg_mode);
+ regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
+ regval |= MA35_GP_MODE_INPUT << gpio * 2;
+ writel(regval, reg_mode);
+
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+
+ return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
+}
+
+static void ma35_gpio_core_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+
+ writel(val, bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
+}
+
+static int ma35_gpio_core_direction_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ void __iomem *reg_dout = bank->reg_base + MA35_GP_REG_DOUT;
+ void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
+ unsigned long flags;
+ unsigned int regval;
+
+ spin_lock_irqsave(&bank->lock, flags);
+
+ regval = readl(reg_dout);
+ if (val)
+ writel(regval | BIT(gpio), reg_dout);
+ else
+ writel(regval & ~BIT(gpio), reg_dout);
+
+ regval = readl(reg_mode);
+ regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
+ regval |= MA35_GP_MODE_OUTPUT << gpio * 2;
+ writel(regval, reg_mode);
+
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int ma35_gpio_core_to_request(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ u32 reg_offs, bit_offs, regval;
+
+ if (gpio < 8) {
+ /* The MFP low register controls port 0 ~ 7 */
+ reg_offs = bank->bank_num * MA35_MFP_REG_SZ_PER_BANK;
+ bit_offs = gpio * MA35_MFP_BITS_PER_PORT;
+ } else {
+ /* The MFP high register controls port 8 ~ 15 */
+ reg_offs = bank->bank_num * MA35_MFP_REG_SZ_PER_BANK + 4;
+ bit_offs = (gpio - 8) * MA35_MFP_BITS_PER_PORT;
+ }
+
+ regmap_read(bank->regmap, MA35_MFP_REG_BASE + reg_offs, ®val);
+ regval &= ~GENMASK(bit_offs + MA35_MFP_BITS_PER_PORT - 1, bit_offs);
+ regmap_write(bank->regmap, MA35_MFP_REG_BASE + reg_offs, regval);
+
+ return 0;
+}
+
+static void ma35_irq_gpio_mask(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+ u32 regval;
+
+ regval = readl(reg_ien);
+
+ /*
+ * The MA35_GP_REG_INTEN bits 0 ~ 15 control low-level or falling edge trigger,
+ * while bits 16 ~ 31 control high-level or rising edge trigger.
+ * We disable both type of interrupt.
+ */
+ regval &= ~(BIT(num + 16) | BIT(num));
+
+ writel(regval, reg_ien);
+}
+
+static void ma35_irq_gpio_unmask(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+ u32 bval, regval;
+
+ bval = bank->irqtype & BIT(num);
+
+ regval = readl(reg_itype);
+ regval &= ~BIT(num);
+ writel(regval | bval, reg_itype);
+
+ bval = bank->irqinten & (BIT(num + 16) | BIT(num));
+
+ regval = readl(reg_ien);
+ regval &= ~(BIT(num + 16) | BIT(num));
+ writel(regval | bval, reg_ien);
+}
+
+static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+
+ if (type == IRQ_TYPE_PROBE) {
+ writel(readl(reg_itype) & ~BIT(num), reg_itype);
+ writel(readl(reg_ien) | BIT(num) | BIT(num + 16), reg_ien);
+ bank->irqtype &= ~BIT(num);
+ bank->irqinten |= BIT(num) | BIT(num + 16);
+ return 0;
+ }
+
+ if (type & IRQ_TYPE_LEVEL_MASK) {
+ writel(readl(reg_itype) | BIT(num), reg_itype);
+ writel(readl(reg_ien) & ~(BIT(num) | BIT(num + 16)), reg_ien);
+ bank->irqtype |= BIT(num);
+ bank->irqinten &= ~(BIT(num) | BIT(num + 16));
+ if (type == IRQ_TYPE_LEVEL_HIGH) {
+ writel(readl(reg_ien) | BIT(num + 16), reg_ien);
+ bank->irqinten |= BIT(num + 16);
+ return 0;
+ }
+
+ if (type == IRQ_TYPE_LEVEL_LOW) {
+ writel(readl(reg_ien) | BIT(num), reg_ien);
+ bank->irqinten |= BIT(num);
+ return 0;
+ }
+
+ } else {
+ writel(readl(reg_itype) & ~BIT(num), reg_itype);
+ bank->irqtype &= ~BIT(num);
+
+ if (type & IRQ_TYPE_EDGE_RISING) {
+ writel(readl(reg_ien) | BIT(num + 16), reg_ien);
+ bank->irqinten |= BIT(num + 16);
+
+ } else {
+ writel(readl(reg_ien) & ~BIT(num + 16), reg_ien);
+ bank->irqinten &= ~BIT(num + 16);
+ }
+
+ if (type & IRQ_TYPE_EDGE_FALLING) {
+ writel(readl(reg_ien) | BIT(num), reg_ien);
+ bank->irqinten |= BIT(num);
+
+ } else {
+ writel(readl(reg_ien) & ~BIT(num), reg_ien);
+ bank->irqinten &= ~BIT(num);
+ }
+ }
+ return 0;
+}
+
+static struct irq_chip ma35_gpio_irqchip = {
+ .name = "MA35-GPIO-IRQ",
+ .irq_disable = ma35_irq_gpio_mask,
+ .irq_enable = ma35_irq_gpio_unmask,
+ .irq_mask = ma35_irq_gpio_mask,
+ .irq_unmask = ma35_irq_gpio_unmask,
+ .irq_set_type = ma35_irq_irqtype,
+ .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE | IRQCHIP_IMMUTABLE,
+};
+
+static void ma35_irq_demux_intgroup(struct irq_desc *desc)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_desc_get_handler_data(desc));
+ struct irq_domain *irqdomain = bank->chip.irq.domain;
+ struct irq_chip *irqchip = irq_desc_get_chip(desc);
+ unsigned int j, isr;
+
+ chained_irq_enter(irqchip, desc);
+
+ isr = readl(bank->reg_base + MA35_GP_REG_INTSRC);
+
+ if (isr != 0) {
+ writel(isr, bank->reg_base + MA35_GP_REG_INTSRC);
+
+ for (j = 0; j < 16; j++) {
+ if (isr & 0x1)
+ generic_handle_irq(irq_find_mapping(irqdomain, j));
+ isr = isr >> 1;
+ }
+ }
+
+ chained_irq_exit(irqchip, desc);
+}
+
+static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
+{
+ struct ma35_pin_ctrl *ctrl = npctl->ctrl;
+ struct ma35_pin_bank *bank = ctrl->pin_banks;
+ int ret;
+ int i;
+
+ for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
+ if (!bank->valid) {
+ dev_warn(&pdev->dev, "bank %s is not valid\n",
+ bank->np->name);
+ continue;
+ }
+ bank->irqtype = 0;
+ bank->irqinten = 0;
+ bank->chip.label = bank->name;
+ bank->chip.of_gpio_n_cells = 2;
+ bank->chip.parent = &pdev->dev;
+ bank->chip.request = ma35_gpio_core_to_request;
+ bank->chip.direction_input = ma35_gpio_core_direction_in;
+ bank->chip.direction_output = ma35_gpio_core_direction_out;
+ bank->chip.get = ma35_gpio_core_get;
+ bank->chip.set = ma35_gpio_core_set;
+ bank->chip.base = -1;
+ bank->chip.ngpio = bank->nr_pins;
+ bank->chip.can_sleep = false;
+ spin_lock_init(&bank->lock);
+
+ if (bank->irq > 0) {
+ struct gpio_irq_chip *girq;
+
+ girq = &bank->chip.irq;
+ gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
+ girq->parent_handler = ma35_irq_demux_intgroup;
+ girq->num_parents = 1;
+
+ girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
+ GFP_KERNEL);
+ if (!girq->parents)
+ return -ENOMEM;
+
+ girq->parents[0] = bank->irq;
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_level_irq;
+ }
+
+ ret = gpiochip_add_data(&bank->chip, bank);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
+ bank->chip.label, ret);
+ goto fail;
+ }
+ }
+ return 0;
+
+fail:
+ for (--i, --bank; i >= 0; --i, --bank) {
+ if (!bank->valid)
+ continue;
+ gpiochip_remove(&bank->chip);
+ }
+ return ret;
+}
+
+static int ma35_get_bank_data(struct ma35_pin_bank *bank, struct ma35_pinctrl *npctl)
+{
+ struct resource res;
+
+ if (of_address_to_resource(bank->np, 0, &res)) {
+ dev_err(npctl->dev, "cannot find IO resource for bank\n");
+ return -ENOENT;
+ }
+
+ bank->reg_base = devm_ioremap_resource(npctl->dev, &res);
+ if (IS_ERR(bank->reg_base)) {
+ dev_err(npctl->dev, "cannot ioremap resource for bank\n");
+ return PTR_ERR(bank->reg_base);
+ }
+
+ bank->irq = irq_of_parse_and_map(bank->np, 0);
+ bank->nr_pins = MA35_GPIO_PORT_MAX;
+
+ bank->clk = of_clk_get(bank->np, 0);
+ if (IS_ERR(bank->clk))
+ return PTR_ERR(bank->clk);
+
+ return clk_prepare_enable(bank->clk);
+}
+
+static int ma35_pinctrl_get_soc_data(struct ma35_pinctrl *pctl, struct platform_device *pdev)
+{
+ struct fwnode_handle *child;
+ struct ma35_pin_ctrl *ctrl;
+ struct ma35_pin_bank *bank;
+ int i, id = 0;
+
+ ctrl = pctl->ctrl;
+ ctrl->nr_banks = MA35_GPIO_BANK_MAX;
+
+ ctrl->pin_banks = devm_kcalloc(&pdev->dev, ctrl->nr_banks,
+ sizeof(*ctrl->pin_banks), GFP_KERNEL);
+ if (!ctrl->pin_banks)
+ return -ENOMEM;
+
+ for (i = 0; i < ctrl->nr_banks; i++) {
+ ctrl->pin_banks[i].bank_num = i;
+ ctrl->pin_banks[i].name = gpio_group_name[i];
+ }
+
+ for_each_gpiochip_node(&pdev->dev, child) {
+ struct device_node *np = to_of_node(child);
+
+ bank = &ctrl->pin_banks[id];
+ bank->np = np;
+ bank->regmap = pctl->regmap;
+ bank->dev = &pdev->dev;
+ if (!ma35_get_bank_data(bank, pctl))
+ bank->valid = true;
+ id++;
+ }
+ return 0;
+}
+
+static void ma35_gpio_cla_port(unsigned int gpio_num, unsigned int *group,
+ unsigned int *num)
+{
+ *group = gpio_num / MA35_GPIO_PORT_MAX;
+ *num = gpio_num % MA35_GPIO_PORT_MAX;
+}
+
+static int ma35_pinconf_set_pull(struct ma35_pinctrl *npctl, unsigned int pin,
+ int pull_up)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_PUSEL);
+ regval &= ~GENMASK(port * 2 + 1, port * 2);
+
+ switch (pull_up) {
+ case PIN_CONFIG_BIAS_PULL_UP:
+ regval |= MA35_GP_PUSEL_PULL_UP << port * 2;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ regval |= MA35_GP_PUSEL_PULL_DOWN << port * 2;
+ break;
+
+ case MA35_GP_PUSEL_DISABLE:
+ regval |= MA35_GP_PUSEL_DISABLE << port * 2;
+ break;
+
+ default:
+ regval |= MA35_GP_PUSEL_DISABLE << port * 2;
+ break;
+ }
+ writel(regval, base + MA35_GP_REG_PUSEL);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_output(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval, mode;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_MODE);
+ mode = (regval & GENMASK(port * 2 + 1, port * 2)) >> port * 2;
+
+ if (mode == MA35_GP_MODE_OUTPUT)
+ return 1;
+
+ return 0;
+}
+
+static int ma35_pinconf_get_pull(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval, mode;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_PUSEL);
+ mode = (regval & GENMASK(port * 2 + 1, port * 2)) >> port * 2;
+
+ switch (mode) {
+ case MA35_GP_PUSEL_PULL_UP:
+ return PIN_CONFIG_BIAS_PULL_UP;
+
+ case MA35_GP_PUSEL_PULL_DOWN:
+ return PIN_CONFIG_BIAS_PULL_DOWN;
+
+ case MA35_GP_PUSEL_DISABLE:
+ return PIN_CONFIG_BIAS_DISABLE;
+ }
+
+ return PIN_CONFIG_BIAS_DISABLE;
+}
+
+static int ma35_pinconf_set_output(struct ma35_pinctrl *npctl, unsigned int pin, bool out)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_MODE);
+ regval &= ~GENMASK(port * 2 + 1, port * 2);
+ regval |= MA35_GP_MODE_OUTPUT << port * 2;
+ writel(regval, base + MA35_GP_REG_MODE);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_power_source(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SPW);
+
+ if (regval & BIT(port))
+ return MVOLT_3300;
+ else
+ return MVOLT_1800;
+}
+
+static int ma35_pinconf_set_power_source(struct ma35_pinctrl *npctl,
+ unsigned int pin, int arg)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ if ((arg != MVOLT_1800) && (arg != MVOLT_3300))
+ return -EINVAL;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SPW);
+
+ if (arg == MVOLT_1800)
+ regval &= ~BIT(port);
+ else
+ regval |= BIT(port);
+
+ writel(regval, base + MA35_GP_REG_SPW);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_drive_strength(struct ma35_pinctrl *npctl, unsigned int pin,
+ u32 *strength)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval, ds_val;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ if (port < MA35_GP_DSH_BASE_PORT) {
+ regval = readl(base + MA35_GP_REG_DSL);
+ ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
+ } else {
+ port -= MA35_GP_DSH_BASE_PORT;
+ regval = readl(base + MA35_GP_REG_DSH);
+ ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
+ }
+
+ if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800)
+ *strength = ds_1800mv_tbl[ds_val];
+ else
+ *strength = ds_3300mv_tbl[ds_val];
+
+ return 0;
+}
+
+static int ma35_pinconf_set_drive_strength(struct ma35_pinctrl *npctl, unsigned int pin,
+ int strength)
+{
+ int port, group_num;
+ void __iomem *base;
+ int i, ds_val = -1;
+ u32 regval;
+
+ if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800) {
+ for (i = 0; i < ARRAY_SIZE(ds_1800mv_tbl); i++) {
+ if (ds_1800mv_tbl[i] == strength)
+ ds_val = i;
+ }
+ } else {
+ for (i = 0; i < ARRAY_SIZE(ds_3300mv_tbl); i++) {
+ if (ds_3300mv_tbl[i] == strength)
+ ds_val = i;
+ }
+ }
+ if (ds_val == -1)
+ return -EINVAL;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ if (port < MA35_GP_DSH_BASE_PORT) {
+ regval = readl(base + MA35_GP_REG_DSL);
+ regval &= ~GENMASK(port * 4 + 2, port * 4);
+ regval |= ds_val << port * 4;
+ writel(regval, base + MA35_GP_REG_DSL);
+ } else {
+ port -= MA35_GP_DSH_BASE_PORT;
+ regval = readl(base + MA35_GP_REG_DSH);
+ regval &= ~GENMASK(port * 4 + 2, port * 4);
+ regval |= ds_val << port * 4;
+ writel(regval, base + MA35_GP_REG_DSH);
+ }
+ return 0;
+}
+
+static int ma35_pinconf_get_schmitt_enable(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SMTEN);
+
+ return !!(regval & BIT(port));
+}
+
+static int ma35_pinconf_set_schmitt(struct ma35_pinctrl *npctl, unsigned int pin, int enable)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SMTEN);
+
+ if (enable)
+ regval |= BIT(port);
+ else
+ regval &= ~BIT(port);
+
+ writel(regval, base + MA35_GP_REG_SMTEN);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_slew_rate(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SLEWCTL);
+
+ return (regval & GENMASK(port * 2 + 1, port * 2)) >> port * 2;
+}
+
+static int ma35_pinconf_set_slew_rate(struct ma35_pinctrl *npctl, unsigned int pin, int rate)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SLEWCTL);
+ regval &= ~GENMASK(port * 2 + 1, port * 2);
+ regval |= rate << port * 2;
+ writel(regval, base + MA35_GP_REG_SLEWCTL);
+
+ return 0;
+}
+
+static int ma35_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param = pinconf_to_config_param(*config);
+ u32 arg;
+ int ret;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (ma35_pinconf_get_pull(npctl, pin) == param)
+ arg = 1;
+ else
+ return -EINVAL;
+ break;
+
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ ret = ma35_pinconf_get_drive_strength(npctl, pin, &arg);
+ if (ret)
+ return ret;
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ arg = ma35_pinconf_get_schmitt_enable(npctl, pin);
+ break;
+
+ case PIN_CONFIG_SLEW_RATE:
+ arg = ma35_pinconf_get_slew_rate(npctl, pin);
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ arg = ma35_pinconf_get_output(npctl, pin);
+ break;
+
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = ma35_pinconf_get_power_source(npctl, pin);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int ma35_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned int num_configs)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param;
+ unsigned int arg = 0;
+ int i, ret = 0;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ ret = ma35_pinconf_set_pull(npctl, pin, param);
+ break;
+
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ ret = ma35_pinconf_set_drive_strength(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ ret = ma35_pinconf_set_schmitt(npctl, pin, 1);
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT:
+ ret = ma35_pinconf_set_schmitt(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_SLEW_RATE:
+ ret = ma35_pinconf_set_slew_rate(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ ret = ma35_pinconf_set_output(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_POWER_SOURCE:
+ ret = ma35_pinconf_set_power_source(npctl, pin, arg);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ }
+ return ret;
+}
+
+static const struct pinconf_ops ma35_pinconf_ops = {
+ .pin_config_get = ma35_pinconf_get,
+ .pin_config_set = ma35_pinconf_set,
+ .is_generic = true,
+};
+
+static int ma35_pinctrl_parse_groups(struct device_node *np, struct ma35_pin_group *grp,
+ struct ma35_pinctrl *npctl, u32 index)
+{
+ unsigned long *configs;
+ unsigned int nconfigs;
+ struct ma35_pin_setting *pin;
+ const __be32 *list;
+ int i, j, size, ret;
+
+ dev_dbg(npctl->dev, "group(%d): %s\n", index, np->name);
+
+ grp->name = np->name;
+
+ ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &nconfigs);
+ if (ret)
+ return ret;
+
+ /*
+ * the binding format is nuvoton,pins = <bank pin-mfp pin-function>,
+ * do sanity check and calculate pins number
+ */
+ list = of_get_property(np, "nuvoton,pins", &size);
+ size /= sizeof(*list);
+ if (!size || size % 3) {
+ dev_err(npctl->dev, "wrong setting!\n");
+ return -EINVAL;
+ }
+ grp->npins = size / 3;
+
+ grp->pins = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
+ if (!grp->pins)
+ return -ENOMEM;
+
+ grp->settings = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->settings), GFP_KERNEL);
+ if (!grp->settings)
+ return -ENOMEM;
+
+ pin = grp->settings;
+
+ for (i = 0, j = 0; i < size; i += 3, j++) {
+ pin->offset = be32_to_cpu(*list++) * MA35_MFP_REG_SZ_PER_BANK + MA35_MFP_REG_BASE;
+ pin->shift = (be32_to_cpu(*list++) * MA35_MFP_BITS_PER_PORT) % 32;
+ pin->muxval = be32_to_cpu(*list++);
+ pin->configs = configs;
+ pin->nconfigs = nconfigs;
+ grp->pins[j] = npctl->info->get_pin_num(pin->offset, pin->shift);
+ pin++;
+ }
+ return 0;
+}
+
+static int ma35_pinctrl_parse_functions(struct device_node *np, struct ma35_pinctrl *npctl,
+ u32 index)
+{
+ struct device_node *child;
+ struct ma35_pin_func *func;
+ struct ma35_pin_group *grp;
+ static u32 grp_index;
+ u32 ret, i = 0;
+
+ dev_dbg(npctl->dev, "parse function(%d): %s\n", index, np->name);
+
+ func = &npctl->functions[index];
+ func->name = np->name;
+ func->ngroups = of_get_child_count(np);
+
+ if (func->ngroups <= 0)
+ return 0;
+
+ func->groups = devm_kcalloc(npctl->dev, func->ngroups, sizeof(char *), GFP_KERNEL);
+ if (!func->groups)
+ return -ENOMEM;
+
+ for_each_child_of_node(np, child) {
+ func->groups[i] = child->name;
+ grp = &npctl->groups[grp_index++];
+ ret = ma35_pinctrl_parse_groups(child, grp, npctl, i++);
+ if (ret) {
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static int ma35_pinctrl_probe_dt(struct platform_device *pdev, struct ma35_pinctrl *npctl)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+ u32 idx = 0;
+ int ret;
+
+ if (!np)
+ return -ENODEV;
+
+ for_each_child_of_node(np, child) {
+ if (of_property_read_bool(child, "gpio-controller"))
+ continue;
+ npctl->nfunctions++;
+ npctl->ngroups += of_get_child_count(child);
+ }
+
+ npctl->functions = devm_kcalloc(&pdev->dev, npctl->nfunctions,
+ sizeof(*npctl->functions), GFP_KERNEL);
+ if (!npctl->functions)
+ return -ENOMEM;
+
+ npctl->groups = devm_kcalloc(&pdev->dev, npctl->ngroups,
+ sizeof(*npctl->groups), GFP_KERNEL);
+ if (!npctl->groups)
+ return -ENOMEM;
+
+ dev_dbg(&pdev->dev, "nfunctions = %d\n", npctl->nfunctions);
+ dev_dbg(&pdev->dev, "ngroups = %d\n", npctl->ngroups);
+
+ for_each_child_of_node(np, child) {
+ if (of_property_read_bool(child, "gpio-controller"))
+ continue;
+
+ ret = ma35_pinctrl_parse_functions(child, npctl, idx++);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to parse function\n");
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+int ma35_pinctrl_probe(struct platform_device *pdev, const struct ma35_pinctrl_soc_info *info)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct pinctrl_desc *ma35_pinctrl_desc;
+ struct ma35_pinctrl *npctl;
+ int ret;
+
+ if (!info || !info->pins || !info->npins) {
+ dev_err(&pdev->dev, "wrong pinctrl info\n");
+ return -EINVAL;
+ }
+
+ npctl = devm_kzalloc(&pdev->dev, sizeof(*npctl), GFP_KERNEL);
+ if (!npctl)
+ return -ENOMEM;
+
+ ma35_pinctrl_desc = devm_kzalloc(&pdev->dev, sizeof(*ma35_pinctrl_desc), GFP_KERNEL);
+ if (!ma35_pinctrl_desc)
+ return -ENOMEM;
+
+ npctl->ctrl = devm_kzalloc(&pdev->dev, sizeof(*npctl->ctrl), GFP_KERNEL);
+ if (!npctl->ctrl)
+ return -ENOMEM;
+
+ ma35_pinctrl_desc->name = dev_name(&pdev->dev);
+ ma35_pinctrl_desc->pins = info->pins;
+ ma35_pinctrl_desc->npins = info->npins;
+ ma35_pinctrl_desc->pctlops = &ma35_pctrl_ops;
+ ma35_pinctrl_desc->pmxops = &ma35_pmx_ops;
+ ma35_pinctrl_desc->confops = &ma35_pinconf_ops;
+ ma35_pinctrl_desc->owner = THIS_MODULE;
+
+ npctl->info = info;
+ npctl->dev = &pdev->dev;
+
+ npctl->regmap = syscon_regmap_lookup_by_phandle(np, "nuvoton,sys");
+ if (IS_ERR(npctl->regmap))
+ return dev_err_probe(&pdev->dev, PTR_ERR(npctl->regmap),
+ "No syscfg phandle specified\n");
+
+ ma35_pinctrl_get_soc_data(npctl, pdev);
+
+ platform_set_drvdata(pdev, npctl);
+
+ ret = ma35_pinctrl_probe_dt(pdev, npctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to probe MA35 pinctrl dt\n");
+
+ ret = devm_pinctrl_register_and_init(&pdev->dev, ma35_pinctrl_desc,
+ npctl, &npctl->pctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to register MA35 pinctrl\n");
+
+ ret = pinctrl_enable(npctl->pctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to enable MA35 pinctrl\n");
+
+ return ma35_gpiolib_register(pdev, npctl);
+}
+
+int __maybe_unused ma35_pinctrl_suspend(struct device *dev)
+{
+ struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
+
+ return pinctrl_force_sleep(npctl->pctl);
+}
+
+int __maybe_unused ma35_pinctrl_resume(struct device *dev)
+{
+ struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
+
+ return pinctrl_force_default(npctl->pctl);
+}
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35.h b/drivers/pinctrl/nuvoton/pinctrl-ma35.h
new file mode 100644
index 000000000000..281605e2c231
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <schung@nuvoton.com>
+ */
+#ifndef __PINCTRL_MA35_H
+#define __PINCTRL_MA35_H
+
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+
+struct ma35_mux_desc {
+ const char *name;
+ u32 muxval;
+};
+
+struct ma35_pin_data {
+ u32 offset;
+ u32 shift;
+ struct ma35_mux_desc *muxes;
+};
+
+struct ma35_pinctrl_soc_info {
+ const struct pinctrl_pin_desc *pins;
+ unsigned int npins;
+ int (*get_pin_num)(int offset, int shift);
+};
+
+#define MA35_PIN(num, n, o, s, ...) { \
+ .number = num, \
+ .name = #n, \
+ .drv_data = &(struct ma35_pin_data) { \
+ .offset = o, \
+ .shift = s, \
+ .muxes = (struct ma35_mux_desc[]) { \
+ __VA_ARGS__, { } }, \
+ }, \
+}
+
+#define MA35_MUX(_val, _name) { \
+ .name = _name, \
+ .muxval = _val, \
+}
+
+int ma35_pinctrl_probe(struct platform_device *pdev, const struct ma35_pinctrl_soc_info *info);
+int ma35_pinctrl_suspend(struct device *dev);
+int ma35_pinctrl_resume(struct device *dev);
+
+#endif /* __PINCTRL_MA35_H */
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c b/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
new file mode 100644
index 000000000000..36510c0b0690
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
@@ -0,0 +1,1797 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <schung@nuvoton.com>
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-ma35.h"
+
+static const struct pinctrl_pin_desc ma35d1_pins[] = {
+ MA35_PIN(0, PA0, 0x80, 0x0,
+ MA35_MUX(0x0, "GPA0"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART16_RXD"),
+ MA35_MUX(0x6, "NAND_DATA0"),
+ MA35_MUX(0x7, "EBI_AD0"),
+ MA35_MUX(0x9, "EBI_ADR0")),
+ MA35_PIN(1, PA1, 0x80, 0x4,
+ MA35_MUX(0x0, "GPA1"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART16_TXD"),
+ MA35_MUX(0x6, "NAND_DATA1"),
+ MA35_MUX(0x7, "EBI_AD1"),
+ MA35_MUX(0x9, "EBI_ADR1")),
+ MA35_PIN(2, PA2, 0x80, 0x8,
+ MA35_MUX(0x0, "GPA2"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x6, "NAND_DATA2"),
+ MA35_MUX(0x7, "EBI_AD2"),
+ MA35_MUX(0x9, "EBI_ADR2")),
+ MA35_PIN(3, PA3, 0x80, 0xc,
+ MA35_MUX(0x0, "GPA3"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x6, "NAND_DATA3"),
+ MA35_MUX(0x7, "EBI_AD3"),
+ MA35_MUX(0x9, "EBI_ADR3")),
+ MA35_PIN(4, PA4, 0x80, 0x10,
+ MA35_MUX(0x0, "GPA4"),
+ MA35_MUX(0x2, "UART3_nCTS"),
+ MA35_MUX(0x3, "UART2_RXD"),
+ MA35_MUX(0x6, "NAND_DATA4"),
+ MA35_MUX(0x7, "EBI_AD4"),
+ MA35_MUX(0x9, "EBI_ADR4")),
+ MA35_PIN(5, PA5, 0x80, 0x14,
+ MA35_MUX(0x0, "GPA5"),
+ MA35_MUX(0x2, "UART3_nRTS"),
+ MA35_MUX(0x3, "UART2_TXD"),
+ MA35_MUX(0x6, "NAND_DATA5"),
+ MA35_MUX(0x7, "EBI_AD5"),
+ MA35_MUX(0x9, "EBI_ADR5")),
+ MA35_PIN(6, PA6, 0x80, 0x18,
+ MA35_MUX(0x0, "GPA6"),
+ MA35_MUX(0x2, "UART3_RXD"),
+ MA35_MUX(0x6, "NAND_DATA6"),
+ MA35_MUX(0x7, "EBI_AD6"),
+ MA35_MUX(0x9, "EBI_ADR6")),
+ MA35_PIN(7, PA7, 0x80, 0x1c,
+ MA35_MUX(0x0, "GPA7"),
+ MA35_MUX(0x2, "UART3_TXD"),
+ MA35_MUX(0x6, "NAND_DATA7"),
+ MA35_MUX(0x7, "EBI_AD7"),
+ MA35_MUX(0x9, "EBI_ADR7")),
+ MA35_PIN(8, PA8, 0x84, 0x0,
+ MA35_MUX(0x0, "GPA8"),
+ MA35_MUX(0x2, "UART5_nCTS"),
+ MA35_MUX(0x3, "UART4_RXD"),
+ MA35_MUX(0x6, "NAND_RDY0"),
+ MA35_MUX(0x7, "EBI_AD8"),
+ MA35_MUX(0x9, "EBI_ADR8")),
+ MA35_PIN(9, PA9, 0x84, 0x4,
+ MA35_MUX(0x0, "GPA9"),
+ MA35_MUX(0x2, "UART5_nRTS"),
+ MA35_MUX(0x3, "UART4_TXD"),
+ MA35_MUX(0x6, "NAND_nRE"),
+ MA35_MUX(0x7, "EBI_AD9"),
+ MA35_MUX(0x9, "EBI_ADR9")),
+ MA35_PIN(10, PA10, 0x84, 0x8,
+ MA35_MUX(0x0, "GPA10"),
+ MA35_MUX(0x2, "UART5_RXD"),
+ MA35_MUX(0x6, "NAND_nWE"),
+ MA35_MUX(0x7, "EBI_AD10"),
+ MA35_MUX(0x9, "EBI_ADR10")),
+ MA35_PIN(11, PA11, 0x84, 0xc,
+ MA35_MUX(0x0, "GPA11"),
+ MA35_MUX(0x2, "UART5_TXD"),
+ MA35_MUX(0x6, "NAND_CLE"),
+ MA35_MUX(0x7, "EBI_AD11"),
+ MA35_MUX(0x9, "EBI_ADR11")),
+ MA35_PIN(12, PA12, 0x84, 0x10,
+ MA35_MUX(0x0, "GPA12"),
+ MA35_MUX(0x2, "UART7_nCTS"),
+ MA35_MUX(0x3, "UART8_RXD"),
+ MA35_MUX(0x6, "NAND_ALE"),
+ MA35_MUX(0x7, "EBI_AD12"),
+ MA35_MUX(0x9, "EBI_ADR12")),
+ MA35_PIN(13, PA13, 0x84, 0x14,
+ MA35_MUX(0x0, "GPA13"),
+ MA35_MUX(0x2, "UART7_nRTS"),
+ MA35_MUX(0x3, "UART8_TXD"),
+ MA35_MUX(0x6, "NAND_nCS0"),
+ MA35_MUX(0x7, "EBI_AD13"),
+ MA35_MUX(0x9, "EBI_ADR13")),
+ MA35_PIN(14, PA14, 0x84, 0x18,
+ MA35_MUX(0x0, "GPA14"),
+ MA35_MUX(0x2, "UART7_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "NAND_nWP"),
+ MA35_MUX(0x7, "EBI_AD14"),
+ MA35_MUX(0x9, "EBI_ADR14")),
+ MA35_PIN(15, PA15, 0x84, 0x1c,
+ MA35_MUX(0x0, "GPA15"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART9_nCTS"),
+ MA35_MUX(0x3, "UART6_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "CAN2_RXD"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0x9, "QEI0_A"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xe, "RGMII0_PPS"),
+ MA35_MUX(0xf, "RMII0_PPS")),
+ MA35_PIN(16, PB0, 0x88, 0x0,
+ MA35_MUX(0x0, "GPB0"),
+ MA35_MUX(0x8, "EADC0_CH0")),
+ MA35_PIN(17, PB1, 0x88, 0x4,
+ MA35_MUX(0x0, "GPB1"),
+ MA35_MUX(0x8, "EADC0_CH1")),
+ MA35_PIN(18, PB2, 0x88, 0x8,
+ MA35_MUX(0x0, "GPB2"),
+ MA35_MUX(0x8, "EADC0_CH2")),
+ MA35_PIN(19, PB3, 0x88, 0xc,
+ MA35_MUX(0x0, "GPB3"),
+ MA35_MUX(0x8, "EADC0_CH3")),
+ MA35_PIN(20, PB4, 0x88, 0x10,
+ MA35_MUX(0x0, "GPB4"),
+ MA35_MUX(0x8, "EADC0_CH4")),
+ MA35_PIN(21, PB5, 0x88, 0x14,
+ MA35_MUX(0x0, "GPB5"),
+ MA35_MUX(0x8, "EADC0_CH5")),
+ MA35_PIN(22, PB6, 0x88, 0x18,
+ MA35_MUX(0x0, "GPB6"),
+ MA35_MUX(0x8, "EADC0_CH6")),
+ MA35_PIN(23, PB7, 0x88, 0x1c,
+ MA35_MUX(0x0, "GPB7"),
+ MA35_MUX(0x8, "EADC0_CH7")),
+ MA35_PIN(24, PB8, 0x8c, 0x0,
+ MA35_MUX(0x0, "GPB8"),
+ MA35_MUX(0x1, "EPWM2_BRAKE0"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x6, "SPI0_I2SMCLK"),
+ MA35_MUX(0x8, "ADC0_CH0"),
+ MA35_MUX(0x9, "EBI_nCS0"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xe, "QEI2_INDEX"),
+ MA35_MUX(0xf, "KPI_ROW6")),
+ MA35_PIN(25, PB9, 0x8c, 0x4,
+ MA35_MUX(0x0, "GPB9"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI0_CLK"),
+ MA35_MUX(0x6, "I2S0_MCLK"),
+ MA35_MUX(0x7, "CCAP1_HSYNC"),
+ MA35_MUX(0x8, "ADC0_CH1"),
+ MA35_MUX(0x9, "EBI_ALE"),
+ MA35_MUX(0xa, "EBI_AD13"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "I2S1_MCLK"),
+ MA35_MUX(0xd, "SC0_nCD"),
+ MA35_MUX(0xe, "QEI2_A"),
+ MA35_MUX(0xf, "KPI_ROW7")),
+ MA35_PIN(26, PB10, 0x8c, 0x8,
+ MA35_MUX(0x0, "GPB10"),
+ MA35_MUX(0x1, "EPWM2_CH5"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI0_MOSI"),
+ MA35_MUX(0x6, "EBI_MCLK"),
+ MA35_MUX(0x7, "CCAP1_VSYNC"),
+ MA35_MUX(0x8, "ADC0_CH2"),
+ MA35_MUX(0x9, "EBI_ADR15"),
+ MA35_MUX(0xa, "EBI_AD14"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "I2C1_SDA"),
+ MA35_MUX(0xd, "INT1"),
+ MA35_MUX(0xe, "QEI2_B")),
+ MA35_PIN(27, PB11, 0x8c, 0xc,
+ MA35_MUX(0x0, "GPB11"),
+ MA35_MUX(0x1, "EPWM2_BRAKE1"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI0_MISO"),
+ MA35_MUX(0x6, "I2S1_MCLK"),
+ MA35_MUX(0x7, "CCAP1_SFIELD"),
+ MA35_MUX(0x8, "ADC0_CH3"),
+ MA35_MUX(0x9, "EBI_nCS2"),
+ MA35_MUX(0xa, "EBI_ALE"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "I2C1_SCL"),
+ MA35_MUX(0xd, "INT2"),
+ MA35_MUX(0xe, "QEI2_INDEX")),
+ MA35_PIN(28, PB12, 0x8c, 0x10,
+ MA35_MUX(0x0, "GPB12"),
+ MA35_MUX(0x1, "EPWM2_CH0"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "CAN2_RXD"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x8, "ADC0_CH4"),
+ MA35_MUX(0x9, "EBI_ADR16"),
+ MA35_MUX(0xe, "ECAP2_IC0")),
+ MA35_PIN(29, PB13, 0x8c, 0x14,
+ MA35_MUX(0x0, "GPB13"),
+ MA35_MUX(0x1, "EPWM2_CH1"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x5, "CAN2_TXD"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x8, "ADC0_CH5"),
+ MA35_MUX(0x9, "EBI_ADR17"),
+ MA35_MUX(0xe, "ECAP2_IC1")),
+ MA35_PIN(30, PB14, 0x8c, 0x18,
+ MA35_MUX(0x0, "GPB14"),
+ MA35_MUX(0x1, "EPWM2_CH2"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "I2C4_SDA"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x8, "ADC0_CH6"),
+ MA35_MUX(0x9, "EBI_ADR18"),
+ MA35_MUX(0xe, "ECAP2_IC2")),
+ MA35_PIN(31, PB15, 0x8c, 0x1c,
+ MA35_MUX(0x0, "GPB15"),
+ MA35_MUX(0x1, "EPWM2_CH3"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "I2C4_SCL"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x8, "ADC0_CH7"),
+ MA35_MUX(0x9, "EBI_ADR19")),
+ MA35_PIN(32, PC0, 0x90, 0x0,
+ MA35_MUX(0x0, "GPC0"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "SD0_CMD/eMMC0_CMD")),
+ MA35_PIN(33, PC1, 0x90, 0x4,
+ MA35_MUX(0x0, "GPC1"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "SD0_CLK/eMMC0_CLK")),
+ MA35_PIN(34, PC2, 0x90, 0x8,
+ MA35_MUX(0x0, "GPC2"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "SD0_DAT0/eMMC0_DAT0")),
+ MA35_PIN(35, PC3, 0x90, 0xc,
+ MA35_MUX(0x0, "GPC3"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "SD0_DAT1/eMMC0_DAT1")),
+ MA35_PIN(36, PC4, 0x90, 0x10,
+ MA35_MUX(0x0, "GPC4"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "SD0_DAT2/eMMC0_DAT2")),
+ MA35_PIN(37, PC5, 0x90, 0x14,
+ MA35_MUX(0x0, "GPC5"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "SD0_DAT3/eMMC0_DAT3")),
+ MA35_PIN(38, PC6, 0x90, 0x18,
+ MA35_MUX(0x0, "GPC6"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "SD0_nCD")),
+ MA35_PIN(39, PC7, 0x90, 0x1c,
+ MA35_MUX(0x0, "GPC7"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "SD0_WP")),
+ MA35_PIN(40, PC12, 0x94, 0x10,
+ MA35_MUX(0x0, "GPC12"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART11_RXD"),
+ MA35_MUX(0x6, "LCM_DATA16")),
+ MA35_PIN(41, PC13, 0x94, 0x14,
+ MA35_MUX(0x0, "GPC13"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART11_TXD"),
+ MA35_MUX(0x6, "LCM_DATA17")),
+ MA35_PIN(42, PC14, 0x94, 0x18,
+ MA35_MUX(0x0, "GPC14"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x6, "LCM_DATA18")),
+ MA35_PIN(43, PC15, 0x94, 0x1c,
+ MA35_MUX(0x0, "GPC15"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x6, "LCM_DATA19"),
+ MA35_MUX(0x7, "LCM_MPU_TE"),
+ MA35_MUX(0x8, "LCM_MPU_VSYNC")),
+ MA35_PIN(44, PD0, 0x98, 0x0,
+ MA35_MUX(0x0, "GPD0"),
+ MA35_MUX(0x2, "UART3_nCTS"),
+ MA35_MUX(0x3, "UART4_RXD"),
+ MA35_MUX(0x5, "QSPI0_SS0")),
+ MA35_PIN(45, PD1, 0x98, 0x4,
+ MA35_MUX(0x0, "GPD1"),
+ MA35_MUX(0x2, "UART3_nRTS"),
+ MA35_MUX(0x3, "UART4_TXD"),
+ MA35_MUX(0x5, "QSPI0_CLK")),
+ MA35_PIN(46, PD2, 0x98, 0x8,
+ MA35_MUX(0x0, "GPD2"),
+ MA35_MUX(0x2, "UART3_RXD"),
+ MA35_MUX(0x5, "QSPI0_MOSI0")),
+ MA35_PIN(47, PD3, 0x98, 0xc,
+ MA35_MUX(0x0, "GPD3"),
+ MA35_MUX(0x2, "UART3_TXD"),
+ MA35_MUX(0x5, "QSPI0_MISO0")),
+ MA35_PIN(48, PD4, 0x98, 0x10,
+ MA35_MUX(0x0, "GPD4"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART2_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "QSPI0_MOSI1")),
+ MA35_PIN(49, PD5, 0x98, 0x14,
+ MA35_MUX(0x0, "GPD5"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART2_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "QSPI0_MISO1")),
+ MA35_PIN(50, PD6, 0x98, 0x18,
+ MA35_MUX(0x0, "GPD6"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x5, "QSPI1_MOSI1"),
+ MA35_MUX(0x6, "I2C0_SDA"),
+ MA35_MUX(0x7, "I2S0_MCLK"),
+ MA35_MUX(0x8, "EPWM0_CH0"),
+ MA35_MUX(0x9, "EBI_AD5"),
+ MA35_MUX(0xa, "SPI3_SS1"),
+ MA35_MUX(0xb, "TRACE_CLK")),
+ MA35_PIN(51, PD7, 0x98, 0x1c,
+ MA35_MUX(0x0, "GPD7"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x5, "QSPI1_MISO1"),
+ MA35_MUX(0x6, "I2C0_SCL"),
+ MA35_MUX(0x7, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EPWM0_CH1"),
+ MA35_MUX(0x9, "EBI_AD6"),
+ MA35_MUX(0xa, "SC1_nCD"),
+ MA35_MUX(0xb, "EADC0_ST")),
+ MA35_PIN(52, PD8, 0x9c, 0x0,
+ MA35_MUX(0x0, "GPD8"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART16_nCTS"),
+ MA35_MUX(0x3, "UART15_RXD"),
+ MA35_MUX(0x5, "QSPI1_SS0"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EPWM0_CH2"),
+ MA35_MUX(0x9, "EBI_AD7"),
+ MA35_MUX(0xa, "SC1_CLK"),
+ MA35_MUX(0xb, "TM0")),
+ MA35_PIN(53, PD9, 0x9c, 0x4,
+ MA35_MUX(0x0, "GPD9"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART16_nRTS"),
+ MA35_MUX(0x3, "UART15_TXD"),
+ MA35_MUX(0x5, "QSPI1_CLK"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EPWM0_CH3"),
+ MA35_MUX(0x9, "EBI_AD8"),
+ MA35_MUX(0xa, "SC1_DAT"),
+ MA35_MUX(0xb, "TM0_EXT")),
+ MA35_PIN(54, PD10, 0x9c, 0x8,
+ MA35_MUX(0x0, "GPD10"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART16_RXD"),
+ MA35_MUX(0x5, "QSPI1_MOSI0"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "EPWM0_CH4"),
+ MA35_MUX(0x9, "EBI_AD9"),
+ MA35_MUX(0xa, "SC1_RST"),
+ MA35_MUX(0xb, "TM2")),
+ MA35_PIN(55, PD11, 0x9c, 0xc,
+ MA35_MUX(0x0, "GPD11"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART16_TXD"),
+ MA35_MUX(0x5, "QSPI1_MISO0"),
+ MA35_MUX(0x7, "I2S1_DO"),
+ MA35_MUX(0x8, "EPWM0_CH5"),
+ MA35_MUX(0x9, "EBI_AD10"),
+ MA35_MUX(0xa, "SC1_PWR"),
+ MA35_MUX(0xb, "TM2_EXT")),
+ MA35_PIN(56, PD12, 0x9c, 0x10,
+ MA35_MUX(0x0, "GPD12"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "TRACE_DATA0"),
+ MA35_MUX(0x7, "EBI_nCS1"),
+ MA35_MUX(0x8, "EBI_AD4"),
+ MA35_MUX(0x9, "QEI0_INDEX"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "I2S1_LRCK"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(57, PD13, 0x9c, 0x14,
+ MA35_MUX(0x0, "GPD13"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "TRACE_DATA1"),
+ MA35_MUX(0x7, "EBI_nCS2"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0x9, "ECAP0_IC0"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "I2S1_BCLK")),
+ MA35_PIN(58, PD14, 0x9c, 0x18,
+ MA35_MUX(0x0, "GPD14"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "TRACE_DATA2"),
+ MA35_MUX(0x7, "EBI_MCLK"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0x9, "ECAP0_IC1"),
+ MA35_MUX(0xb, "TM6"),
+ MA35_MUX(0xc, "I2S1_DI"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(59, PD15, 0x9c, 0x1c,
+ MA35_MUX(0x0, "GPD15"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "TRACE_DATA3"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0x9, "ECAP0_IC2"),
+ MA35_MUX(0xb, "TM6_EXT"),
+ MA35_MUX(0xc, "I2S1_DO")),
+ MA35_PIN(60, PE0, 0xa0, 0x0,
+ MA35_MUX(0x0, "GPE0"),
+ MA35_MUX(0x2, "UART9_nCTS"),
+ MA35_MUX(0x3, "UART8_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA0"),
+ MA35_MUX(0x8, "RGMII0_MDC"),
+ MA35_MUX(0x9, "RMII0_MDC")),
+ MA35_PIN(61, PE1, 0xa0, 0x4,
+ MA35_MUX(0x0, "GPE1"),
+ MA35_MUX(0x2, "UART9_nRTS"),
+ MA35_MUX(0x3, "UART8_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA1"),
+ MA35_MUX(0x8, "RGMII0_MDIO"),
+ MA35_MUX(0x9, "RMII0_MDIO")),
+ MA35_PIN(62, PE2, 0xa0, 0x8,
+ MA35_MUX(0x0, "GPE2"),
+ MA35_MUX(0x2, "UART9_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA2"),
+ MA35_MUX(0x8, "RGMII0_TXCTL"),
+ MA35_MUX(0x9, "RMII0_TXEN")),
+ MA35_PIN(63, PE3, 0xa0, 0xc,
+ MA35_MUX(0x0, "GPE3"),
+ MA35_MUX(0x2, "UART9_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA3"),
+ MA35_MUX(0x8, "RGMII0_TXD0"),
+ MA35_MUX(0x9, "RMII0_TXD0")),
+ MA35_PIN(64, PE4, 0xa0, 0x10,
+ MA35_MUX(0x0, "GPE4"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA4"),
+ MA35_MUX(0x8, "RGMII0_TXD1"),
+ MA35_MUX(0x9, "RMII0_TXD1")),
+ MA35_PIN(65, PE5, 0xa0, 0x14,
+ MA35_MUX(0x0, "GPE5"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA5"),
+ MA35_MUX(0x8, "RGMII0_RXCLK"),
+ MA35_MUX(0x9, "RMII0_REFCLK")),
+ MA35_PIN(66, PE6, 0xa0, 0x18,
+ MA35_MUX(0x0, "GPE6"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA6"),
+ MA35_MUX(0x8, "RGMII0_RXCTL"),
+ MA35_MUX(0x9, "RMII0_CRSDV")),
+ MA35_PIN(67, PE7, 0xa0, 0x1c,
+ MA35_MUX(0x0, "GPE7"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA7"),
+ MA35_MUX(0x8, "RGMII0_RXD0"),
+ MA35_MUX(0x9, "RMII0_RXD0")),
+ MA35_PIN(68, PE8, 0xa4, 0x0,
+ MA35_MUX(0x0, "GPE8"),
+ MA35_MUX(0x2, "UART13_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x7, "CCAP1_SCLK"),
+ MA35_MUX(0x8, "RGMII0_RXD1"),
+ MA35_MUX(0x9, "RMII0_RXD1")),
+ MA35_PIN(69, PE9, 0xa4, 0x4,
+ MA35_MUX(0x0, "GPE9"),
+ MA35_MUX(0x2, "UART13_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x7, "CCAP1_PIXCLK"),
+ MA35_MUX(0x8, "RGMII0_RXD2"),
+ MA35_MUX(0x9, "RMII0_RXERR")),
+ MA35_PIN(70, PE10, 0xa4, 0x8,
+ MA35_MUX(0x0, "GPE10"),
+ MA35_MUX(0x2, "UART15_nCTS"),
+ MA35_MUX(0x3, "UART14_RXD"),
+ MA35_MUX(0x5, "SPI1_SS0"),
+ MA35_MUX(0x7, "CCAP1_HSYNC"),
+ MA35_MUX(0x8, "RGMII0_RXD3")),
+ MA35_PIN(71, PE11, 0xa4, 0xc,
+ MA35_MUX(0x0, "GPE11"),
+ MA35_MUX(0x2, "UART15_nRTS"),
+ MA35_MUX(0x3, "UART14_TXD"),
+ MA35_MUX(0x5, "SPI1_CLK"),
+ MA35_MUX(0x7, "CCAP1_VSYNC"),
+ MA35_MUX(0x8, "RGMII0_TXCLK")),
+ MA35_PIN(72, PE12, 0xa4, 0x10,
+ MA35_MUX(0x0, "GPE12"),
+ MA35_MUX(0x2, "UART15_RXD"),
+ MA35_MUX(0x5, "SPI1_MOSI"),
+ MA35_MUX(0x7, "CCAP1_DATA8"),
+ MA35_MUX(0x8, "RGMII0_TXD2")),
+ MA35_PIN(73, PE13, 0xa4, 0x14,
+ MA35_MUX(0x0, "GPE13"),
+ MA35_MUX(0x2, "UART15_TXD"),
+ MA35_MUX(0x5, "SPI1_MISO"),
+ MA35_MUX(0x7, "CCAP1_DATA9"),
+ MA35_MUX(0x8, "RGMII0_TXD3")),
+ MA35_PIN(74, PE14, 0xa4, 0x18,
+ MA35_MUX(0x0, "GPE14"),
+ MA35_MUX(0x1, "UART0_TXD")),
+ MA35_PIN(75, PE15, 0xa4, 0x1c,
+ MA35_MUX(0x0, "GPE15"),
+ MA35_MUX(0x1, "UART0_RXD")),
+ MA35_PIN(76, PF0, 0xa8, 0x0,
+ MA35_MUX(0x0, "GPF0"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x6, "RGMII0_RXD3"),
+ MA35_MUX(0x8, "RGMII1_MDC"),
+ MA35_MUX(0x9, "RMII1_MDC"),
+ MA35_MUX(0xe, "KPI_COL0")),
+ MA35_PIN(77, PF1, 0xa8, 0x4,
+ MA35_MUX(0x0, "GPF1"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x6, "RGMII0_TXCLK"),
+ MA35_MUX(0x8, "RGMII1_MDIO"),
+ MA35_MUX(0x9, "RMII1_MDIO"),
+ MA35_MUX(0xe, "KPI_COL1")),
+ MA35_PIN(78, PF2, 0xa8, 0x8,
+ MA35_MUX(0x0, "GPF2"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x6, "RGMII0_TXD2"),
+ MA35_MUX(0x8, "RGMII1_TXCTL"),
+ MA35_MUX(0x9, "RMII1_TXEN"),
+ MA35_MUX(0xe, "KPI_COL2")),
+ MA35_PIN(79, PF3, 0xa8, 0xc,
+ MA35_MUX(0x0, "GPF3"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x6, "RGMII0_TXD3"),
+ MA35_MUX(0x8, "RGMII1_TXD0"),
+ MA35_MUX(0x9, "RMII1_TXD0"),
+ MA35_MUX(0xe, "KPI_COL3")),
+ MA35_PIN(80, PF4, 0xa8, 0x10,
+ MA35_MUX(0x0, "GPF4"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2S0_LRCK"),
+ MA35_MUX(0x5, "SPI1_SS0"),
+ MA35_MUX(0x8, "RGMII1_TXD1"),
+ MA35_MUX(0x9, "RMII1_TXD1"),
+ MA35_MUX(0xd, "CAN2_RXD"),
+ MA35_MUX(0xe, "KPI_ROW0")),
+ MA35_PIN(81, PF5, 0xa8, 0x14,
+ MA35_MUX(0x0, "GPF5"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2S0_BCLK"),
+ MA35_MUX(0x5, "SPI1_CLK"),
+ MA35_MUX(0x8, "RGMII1_RXCLK"),
+ MA35_MUX(0x9, "RMII1_REFCLK"),
+ MA35_MUX(0xd, "CAN2_TXD"),
+ MA35_MUX(0xe, "KPI_ROW1")),
+ MA35_PIN(82, PF6, 0xa8, 0x18,
+ MA35_MUX(0x0, "GPF6"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x4, "I2S0_DI"),
+ MA35_MUX(0x5, "SPI1_MOSI"),
+ MA35_MUX(0x8, "RGMII1_RXCTL"),
+ MA35_MUX(0x9, "RMII1_CRSDV"),
+ MA35_MUX(0xa, "I2C4_SDA"),
+ MA35_MUX(0xd, "SC0_CLK"),
+ MA35_MUX(0xe, "KPI_ROW2")),
+ MA35_PIN(83, PF7, 0xa8, 0x1c,
+ MA35_MUX(0x0, "GPF7"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x4, "I2S0_DO"),
+ MA35_MUX(0x5, "SPI1_MISO"),
+ MA35_MUX(0x8, "RGMII1_RXD0"),
+ MA35_MUX(0x9, "RMII1_RXD0"),
+ MA35_MUX(0xa, "I2C4_SCL"),
+ MA35_MUX(0xd, "SC0_DAT"),
+ MA35_MUX(0xe, "KPI_ROW3")),
+ MA35_PIN(84, PF8, 0xac, 0x0,
+ MA35_MUX(0x0, "GPF8"),
+ MA35_MUX(0x2, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x8, "RGMII1_RXD1"),
+ MA35_MUX(0x9, "RMII1_RXD1"),
+ MA35_MUX(0xd, "SC0_RST"),
+ MA35_MUX(0xe, "KPI_COL4")),
+ MA35_PIN(85, PF9, 0xac, 0x4,
+ MA35_MUX(0x0, "GPF9"),
+ MA35_MUX(0x2, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x8, "RGMII1_RXD2"),
+ MA35_MUX(0x9, "RMII1_RXERR"),
+ MA35_MUX(0xd, "SC0_PWR"),
+ MA35_MUX(0xe, "KPI_COL5")),
+ MA35_PIN(86, PF10, 0xac, 0x8,
+ MA35_MUX(0x0, "GPF10"),
+ MA35_MUX(0x2, "UART13_nCTS"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x6, "SPI1_SS0"),
+ MA35_MUX(0x8, "RGMII1_RXD3"),
+ MA35_MUX(0x9, "SC0_CLK"),
+ MA35_MUX(0xe, "KPI_COL6")),
+ MA35_PIN(87, PF11, 0xac, 0xc,
+ MA35_MUX(0x0, "GPF11"),
+ MA35_MUX(0x2, "UART13_nRTS"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x6, "SPI1_CLK"),
+ MA35_MUX(0x8, "RGMII1_TXCLK"),
+ MA35_MUX(0x9, "SC0_DAT"),
+ MA35_MUX(0xe, "KPI_COL7")),
+ MA35_PIN(88, PF12, 0xac, 0x10,
+ MA35_MUX(0x0, "GPF12"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "SPI1_MOSI"),
+ MA35_MUX(0x8, "RGMII1_TXD2"),
+ MA35_MUX(0x9, "SC0_RST"),
+ MA35_MUX(0xe, "KPI_ROW4")),
+ MA35_PIN(89, PF13, 0xac, 0x14,
+ MA35_MUX(0x0, "GPF13"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x6, "SPI1_MISO"),
+ MA35_MUX(0x8, "RGMII1_TXD3"),
+ MA35_MUX(0x9, "SC0_PWR"),
+ MA35_MUX(0xe, "KPI_ROW5")),
+ MA35_PIN(90, PF14, 0xac, 0x18,
+ MA35_MUX(0x0, "GPF14"),
+ MA35_MUX(0x1, "EPWM2_BRAKE0"),
+ MA35_MUX(0x2, "EADC0_ST"),
+ MA35_MUX(0x3, "RGMII1_PPS"),
+ MA35_MUX(0x4, "RMII1_PPS"),
+ MA35_MUX(0x5, "SPI0_I2SMCLK"),
+ MA35_MUX(0x6, "SPI1_I2SMCLK"),
+ MA35_MUX(0x7, "CCAP1_SFIELD"),
+ MA35_MUX(0x8, "RGMII0_PPS"),
+ MA35_MUX(0x9, "RMII0_PPS"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "INT0"),
+ MA35_MUX(0xd, "SPI1_SS1"),
+ MA35_MUX(0xe, "QEI2_INDEX"),
+ MA35_MUX(0xf, "I2S0_MCLK")),
+ MA35_PIN(91, PF15, 0xac, 0x1c,
+ MA35_MUX(0x0, "GPF15"),
+ MA35_MUX(0x1, "HSUSB0_VBUSVLD")),
+ MA35_PIN(92, PG0, 0xb0, 0x0,
+ MA35_MUX(0x0, "GPG0"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART7_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x7, "EBI_AD15"),
+ MA35_MUX(0x9, "I2S1_MCLK"),
+ MA35_MUX(0xa, "QEI0_INDEX"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xc, "CLKO"),
+ MA35_MUX(0xd, "INT0"),
+ MA35_MUX(0xf, "EBI_ADR15")),
+ MA35_PIN(93, PG1, 0xb0, 0x4,
+ MA35_MUX(0x0, "GPG1"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART9_nRTS"),
+ MA35_MUX(0x3, "UART6_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "CAN2_TXD"),
+ MA35_MUX(0x7, "EBI_nCS0"),
+ MA35_MUX(0x9, "QEI0_B"),
+ MA35_MUX(0xb, "TM1_EXT"),
+ MA35_MUX(0xe, "RGMII1_PPS"),
+ MA35_MUX(0xf, "RMII1_PPS")),
+ MA35_PIN(94, PG2, 0xb0, 0x8,
+ MA35_MUX(0x0, "GPG2"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART9_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x7, "EBI_ADR16"),
+ MA35_MUX(0x8, "EBI_nCS2"),
+ MA35_MUX(0xa, "QEI0_A"),
+ MA35_MUX(0xb, "TM3"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(95, PG3, 0xb0, 0xc,
+ MA35_MUX(0x0, "GPG3"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART9_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI0_I2SMCLK"),
+ MA35_MUX(0x7, "EBI_ADR17"),
+ MA35_MUX(0x8, "EBI_nCS1"),
+ MA35_MUX(0x9, "EBI_MCLK"),
+ MA35_MUX(0xa, "QEI0_B"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xc, "I2S1_MCLK")),
+ MA35_PIN(96, PG4, 0xb0, 0x10,
+ MA35_MUX(0x0, "GPG4"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART5_nCTS"),
+ MA35_MUX(0x3, "UART6_RXD"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "QEI1_INDEX"),
+ MA35_MUX(0x7, "EBI_ADR18"),
+ MA35_MUX(0x8, "EBI_nCS0"),
+ MA35_MUX(0x9, "I2S1_DO"),
+ MA35_MUX(0xa, "SC1_CLK"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xd, "INT2"),
+ MA35_MUX(0xe, "ECAP1_IC2")),
+ MA35_PIN(97, PG5, 0xb0, 0x14,
+ MA35_MUX(0x0, "GPG5"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART5_nRTS"),
+ MA35_MUX(0x3, "UART6_TXD"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "ECAP0_IC0"),
+ MA35_MUX(0x7, "EBI_ADR19"),
+ MA35_MUX(0x8, "EBI_ALE"),
+ MA35_MUX(0x9, "I2S1_DI"),
+ MA35_MUX(0xa, "SC1_DAT"),
+ MA35_MUX(0xb, "TM4_EXT")),
+ MA35_PIN(98, PG6, 0xb0, 0x18,
+ MA35_MUX(0x0, "GPG6"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART5_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "ECAP0_IC1"),
+ MA35_MUX(0x7, "EBI_nRD"),
+ MA35_MUX(0x9, "I2S1_BCLK"),
+ MA35_MUX(0xa, "SC1_RST"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(99, PG7, 0xb0, 0x1c,
+ MA35_MUX(0x0, "GPG7"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART5_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "ECAP0_IC2"),
+ MA35_MUX(0x7, "EBI_nWR"),
+ MA35_MUX(0x9, "I2S1_LRCK"),
+ MA35_MUX(0xa, "SC1_PWR"),
+ MA35_MUX(0xb, "TM7_EXT")),
+ MA35_PIN(100, PG8, 0xb4, 0x0,
+ MA35_MUX(0x0, "GPG8"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "LCM_VSYNC"),
+ MA35_MUX(0x7, "I2C3_SDA"),
+ MA35_MUX(0xc, "EBI_AD7"),
+ MA35_MUX(0xd, "EBI_nCS0")),
+ MA35_PIN(101, PG9, 0xb4, 0x4,
+ MA35_MUX(0x0, "GPG9"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "LCM_HSYNC"),
+ MA35_MUX(0x7, "I2C3_SCL"),
+ MA35_MUX(0xc, "EBI_AD8"),
+ MA35_MUX(0xd, "EBI_nCS1")),
+ MA35_PIN(102, PG10, 0xb4, 0x8,
+ MA35_MUX(0x0, "GPG10"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "LCM_CLK"),
+ MA35_MUX(0xc, "EBI_AD9"),
+ MA35_MUX(0xd, "EBI_nWRH")),
+ MA35_PIN(103, PG11, 0xb4, 0xc,
+ MA35_MUX(0x0, "GPG11"),
+ MA35_MUX(0x3, "JTAG_TDO"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "NAND_RDY1"),
+ MA35_MUX(0x7, "EBI_nWRH"),
+ MA35_MUX(0x8, "EBI_nCS1"),
+ MA35_MUX(0xa, "EBI_AD0")),
+ MA35_PIN(104, PG12, 0xb4, 0x10,
+ MA35_MUX(0x0, "GPG12"),
+ MA35_MUX(0x3, "JTAG_TCK/SW_CLK"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x7, "EBI_nWRL"),
+ MA35_MUX(0xa, "EBI_AD1")),
+ MA35_PIN(105, PG13, 0xb4, 0x14,
+ MA35_MUX(0x0, "GPG13"),
+ MA35_MUX(0x3, "JTAG_TMS/SW_DIO"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x7, "EBI_MCLK"),
+ MA35_MUX(0xa, "EBI_AD2")),
+ MA35_PIN(106, PG14, 0xb4, 0x18,
+ MA35_MUX(0x0, "GPG14"),
+ MA35_MUX(0x3, "JTAG_TDI"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "NAND_nCS1"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0xa, "EBI_AD3")),
+ MA35_PIN(107, PG15, 0xb4, 0x1c,
+ MA35_MUX(0x0, "GPG15"),
+ MA35_MUX(0x3, "JTAG_nTRST"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x7, "EBI_nCS0"),
+ MA35_MUX(0xa, "EBI_AD4")),
+ MA35_PIN(108, PH0, 0xb8, 0x0,
+ MA35_MUX(0x0, "GPH0"),
+ MA35_MUX(0x2, "UART8_nCTS"),
+ MA35_MUX(0x3, "UART7_RXD"),
+ MA35_MUX(0x6, "LCM_DATA8")),
+ MA35_PIN(109, PH1, 0xb8, 0x4,
+ MA35_MUX(0x0, "GPH1"),
+ MA35_MUX(0x2, "UART8_nRTS"),
+ MA35_MUX(0x3, "UART7_TXD"),
+ MA35_MUX(0x6, "LCM_DATA9")),
+ MA35_PIN(110, PH2, 0xb8, 0x8,
+ MA35_MUX(0x0, "GPH2"),
+ MA35_MUX(0x2, "UART8_RXD"),
+ MA35_MUX(0x6, "LCM_DATA10")),
+ MA35_PIN(111, PH3, 0xb8, 0xc,
+ MA35_MUX(0x0, "GPH3"),
+ MA35_MUX(0x2, "UART8_TXD"),
+ MA35_MUX(0x6, "LCM_DATA11")),
+ MA35_PIN(112, PH4, 0xb8, 0x10,
+ MA35_MUX(0x0, "GPH4"),
+ MA35_MUX(0x2, "UART10_nCTS"),
+ MA35_MUX(0x3, "UART9_RXD"),
+ MA35_MUX(0x6, "LCM_DATA12")),
+ MA35_PIN(113, PH5, 0xb8, 0x14,
+ MA35_MUX(0x0, "GPH5"),
+ MA35_MUX(0x2, "UART10_nRTS"),
+ MA35_MUX(0x3, "UART9_TXD"),
+ MA35_MUX(0x6, "LCM_DATA13")),
+ MA35_PIN(114, PH6, 0xb8, 0x18,
+ MA35_MUX(0x0, "GPH6"),
+ MA35_MUX(0x2, "UART10_RXD"),
+ MA35_MUX(0x6, "LCM_DATA14")),
+ MA35_PIN(115, PH7, 0xb8, 0x1c,
+ MA35_MUX(0x0, "GPH7"),
+ MA35_MUX(0x2, "UART10_TXD"),
+ MA35_MUX(0x6, "LCM_DATA15")),
+ MA35_PIN(116, PH8, 0xbc, 0x0,
+ MA35_MUX(0x0, "GPH8"),
+ MA35_MUX(0x6, "TAMPER0")),
+ MA35_PIN(117, PH9, 0xbc, 0x4,
+ MA35_MUX(0x0, "GPH9"),
+ MA35_MUX(0x4, "CLK_32KOUT"),
+ MA35_MUX(0x6, "TAMPER1")),
+ MA35_PIN(118, PH12, 0xbc, 0x10,
+ MA35_MUX(0x0, "GPH12"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x6, "LCM_DATA20")),
+ MA35_PIN(119, PH13, 0xbc, 0x14,
+ MA35_MUX(0x0, "GPH13"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x6, "LCM_DATA21")),
+ MA35_PIN(120, PH14, 0xbc, 0x18,
+ MA35_MUX(0x0, "GPH14"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x6, "LCM_DATA22")),
+ MA35_PIN(121, PH15, 0xbc, 0x1c,
+ MA35_MUX(0x0, "GPH15"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x6, "LCM_DATA23")),
+ MA35_PIN(122, PI0, 0xc0, 0x0,
+ MA35_MUX(0x0, "GPI0"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART11_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x7, "SC0_nCD"),
+ MA35_MUX(0x8, "EBI_ADR0"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "ECAP1_IC0")),
+ MA35_PIN(123, PI1, 0xc0, 0x4,
+ MA35_MUX(0x0, "GPI1"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART11_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x7, "SC0_CLK"),
+ MA35_MUX(0x8, "EBI_ADR1"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "ECAP1_IC1")),
+ MA35_PIN(124, PI2, 0xc0, 0x8,
+ MA35_MUX(0x0, "GPI2"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x7, "SC0_DAT"),
+ MA35_MUX(0x8, "EBI_ADR2"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xc, "ECAP1_IC2")),
+ MA35_PIN(125, PI3, 0xc0, 0xc,
+ MA35_MUX(0x0, "GPI3"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x7, "SC0_RST"),
+ MA35_MUX(0x8, "EBI_ADR3"),
+ MA35_MUX(0xb, "TM1_EXT")),
+ MA35_PIN(126, PI4, 0xc0, 0x10,
+ MA35_MUX(0x0, "GPI4"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI2_SS1"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EBI_ADR4"),
+ MA35_MUX(0xd, "INT0")),
+ MA35_PIN(127, PI5, 0xc0, 0x14,
+ MA35_MUX(0x0, "GPI5"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EBI_ADR5"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(128, PI6, 0xc0, 0x18,
+ MA35_MUX(0x0, "GPI6"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x8, "EBI_ADR6"),
+ MA35_MUX(0xc, "QEI1_INDEX"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(129, PI7, 0xc0, 0x1c,
+ MA35_MUX(0x0, "GPI7"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x8, "EBI_ADR7"),
+ MA35_MUX(0xc, "ECAP0_IC0"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(130, PI8, 0xc4, 0x0,
+ MA35_MUX(0x0, "GPI8"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x6, "LCM_DATA0"),
+ MA35_MUX(0xc, "EBI_AD11")),
+ MA35_PIN(131, PI9, 0xc4, 0x4,
+ MA35_MUX(0x0, "GPI9"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x6, "LCM_DATA1"),
+ MA35_MUX(0xc, "EBI_AD12")),
+ MA35_PIN(132, PI10, 0xc4, 0x8,
+ MA35_MUX(0x0, "GPI10"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x6, "LCM_DATA2"),
+ MA35_MUX(0xc, "EBI_AD13")),
+ MA35_PIN(133, PI11, 0xC4, 0xc,
+ MA35_MUX(0x0, "GPI11"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x6, "LCM_DATA3"),
+ MA35_MUX(0xc, "EBI_AD14")),
+ MA35_PIN(134, PI12, 0xc4, 0x10,
+ MA35_MUX(0x0, "GPI12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART5_RXD"),
+ MA35_MUX(0x6, "LCM_DATA4")),
+ MA35_PIN(135, PI13, 0xc4, 0x14,
+ MA35_MUX(0x0, "GPI13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART5_TXD"),
+ MA35_MUX(0x6, "LCM_DATA5")),
+ MA35_PIN(136, PI14, 0xc4, 0x18,
+ MA35_MUX(0x0, "GPI14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x6, "LCM_DATA6")),
+ MA35_PIN(137, PI15, 0xc4, 0x1c,
+ MA35_MUX(0x0, "GPI15"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x6, "LCM_DATA7")),
+ MA35_PIN(138, PJ0, 0xc8, 0x0,
+ MA35_MUX(0x0, "GPJ0"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART8_nCTS"),
+ MA35_MUX(0x3, "UART7_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "eMMC1_DAT4"),
+ MA35_MUX(0x7, "I2S0_LRCK"),
+ MA35_MUX(0x8, "SC0_CLK"),
+ MA35_MUX(0x9, "EBI_AD11"),
+ MA35_MUX(0xa, "EBI_ADR16"),
+ MA35_MUX(0xb, "EBI_nCS0"),
+ MA35_MUX(0xc, "EBI_AD7")),
+ MA35_PIN(139, PJ1, 0xc8, 0x4,
+ MA35_MUX(0x0, "GPJ1"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART8_nRTS"),
+ MA35_MUX(0x3, "UART7_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "eMMC1_DAT5"),
+ MA35_MUX(0x7, "I2S0_BCLK"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0x9, "EBI_AD12"),
+ MA35_MUX(0xa, "EBI_ADR17"),
+ MA35_MUX(0xb, "EBI_nCS1"),
+ MA35_MUX(0xc, "EBI_AD8")),
+ MA35_PIN(140, PJ2, 0xc8, 0x8,
+ MA35_MUX(0x0, "GPJ2"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART8_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "eMMC1_DAT6"),
+ MA35_MUX(0x7, "I2S0_DI"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0x9, "EBI_AD13"),
+ MA35_MUX(0xa, "EBI_ADR18"),
+ MA35_MUX(0xb, "EBI_nWRH"),
+ MA35_MUX(0xc, "EBI_AD9")),
+ MA35_PIN(141, PJ3, 0xc8, 0xc,
+ MA35_MUX(0x0, "GPJ3"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART8_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "eMMC1_DAT7"),
+ MA35_MUX(0x7, "I2S0_DO"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0x9, "EBI_AD14"),
+ MA35_MUX(0xa, "EBI_ADR19"),
+ MA35_MUX(0xb, "EBI_nWRL"),
+ MA35_MUX(0xc, "EBI_AD10")),
+ MA35_PIN(142, PJ4, 0xc8, 0x10,
+ MA35_MUX(0x0, "GPJ4"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x6, "SD1_WP")),
+ MA35_PIN(143, PJ5, 0xc8, 0x14,
+ MA35_MUX(0x0, "GPJ5"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "SD1_nCD")),
+ MA35_PIN(144, PJ6, 0xc8, 0x18,
+ MA35_MUX(0x0, "GPJ6"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "SD1_CMD/eMMC1_CMD")),
+ MA35_PIN(145, PJ7, 0xc8, 0x1c,
+ MA35_MUX(0x0, "GPJ7"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "SD1_CLK/eMMC1_CLK")),
+ MA35_PIN(146, PJ8, 0xcc, 0x0,
+ MA35_MUX(0x0, "GPJ8"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "SD1_DAT0/eMMC1_DAT0")),
+ MA35_PIN(147, PJ9, 0xcc, 0x4,
+ MA35_MUX(0x0, "GPJ9"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "SD1_DAT1/eMMC1_DAT1")),
+ MA35_PIN(148, PJ10, 0xcc, 0x8,
+ MA35_MUX(0x0, "GPJ10"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "SD1_DAT2/eMMC1_DAT2")),
+ MA35_PIN(149, PJ11, 0xcc, 0xc,
+ MA35_MUX(0x0, "GPJ11"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "SD1_DAT3/eMMC1_DAT3")),
+ MA35_PIN(150, PJ12, 0xcc, 0x10,
+ MA35_MUX(0x0, "GPJ12"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x7, "SC1_CLK"),
+ MA35_MUX(0x8, "EBI_ADR12"),
+ MA35_MUX(0xb, "TM2"),
+ MA35_MUX(0xc, "QEI0_INDEX")),
+ MA35_PIN(151, PJ13, 0xcc, 0x14,
+ MA35_MUX(0x0, "GPJ13"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x7, "SC1_DAT"),
+ MA35_MUX(0x8, "EBI_ADR13"),
+ MA35_MUX(0xb, "TM2_EXT")),
+ MA35_PIN(152, PJ14, 0xcc, 0x18,
+ MA35_MUX(0x0, "GPJ14"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x7, "SC1_RST"),
+ MA35_MUX(0x8, "EBI_ADR14"),
+ MA35_MUX(0xb, "TM3")),
+ MA35_PIN(153, PJ15, 0xcc, 0x1c,
+ MA35_MUX(0x0, "GPJ15"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x7, "SC1_PWR"),
+ MA35_MUX(0x8, "EBI_ADR15"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(154, PK0, 0xd0, 0x0,
+ MA35_MUX(0x0, "GPK0"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART16_nCTS"),
+ MA35_MUX(0x3, "UART15_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EBI_ADR8"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xc, "ECAP0_IC1")),
+ MA35_PIN(155, PK1, 0xd0, 0x4,
+ MA35_MUX(0x0, "GPK1"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART16_nRTS"),
+ MA35_MUX(0x3, "UART15_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x8, "EBI_ADR9"),
+ MA35_MUX(0xb, "TM7_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC2")),
+ MA35_PIN(156, PK2, 0xd0, 0x8,
+ MA35_MUX(0x0, "GPK2"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART16_RXD"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x5, "SPI3_I2SMCLK"),
+ MA35_MUX(0x7, "SC0_PWR"),
+ MA35_MUX(0x8, "EBI_ADR10"),
+ MA35_MUX(0xc, "QEI0_A")),
+ MA35_PIN(157, PK3, 0xd0, 0xc,
+ MA35_MUX(0x0, "GPK3"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART16_TXD"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x5, "SPI3_SS1"),
+ MA35_MUX(0x7, "SC1_nCD"),
+ MA35_MUX(0x8, "EBI_ADR11"),
+ MA35_MUX(0xc, "QEI0_B")),
+ MA35_PIN(158, PK4, 0xd0, 0x10,
+ MA35_MUX(0x0, "GPK4"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "LCM_DEN"),
+ MA35_MUX(0xc, "EBI_AD10"),
+ MA35_MUX(0xd, "EBI_nWRL")),
+ MA35_PIN(159, PK5, 0xd0, 0x14,
+ MA35_MUX(0x0, "GPK5"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xb, "TM8_EXT"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(160, PK6, 0xd0, 0x18,
+ MA35_MUX(0x0, "GPK6"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0xb, "TM6"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(161, PK7, 0xd0, 0x1c,
+ MA35_MUX(0x0, "GPK7"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0x9, "CLKO"),
+ MA35_MUX(0xb, "TM6_EXT"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(162, PK8, 0xd4, 0x0,
+ MA35_MUX(0x0, "GPK8"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x7, "EADC0_ST"),
+ MA35_MUX(0x8, "EBI_AD15"),
+ MA35_MUX(0x9, "EBI_MCLK"),
+ MA35_MUX(0xa, "EBI_ADR15"),
+ MA35_MUX(0xb, "TM8"),
+ MA35_MUX(0xc, "QEI1_INDEX")),
+ MA35_PIN(163, PK9, 0xd4, 0x4,
+ MA35_MUX(0x0, "GPK9"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "CCAP0_SCLK"),
+ MA35_MUX(0x8, "EBI_AD0"),
+ MA35_MUX(0xa, "EBI_ADR0")),
+ MA35_PIN(164, PK10, 0xd4, 0x8,
+ MA35_MUX(0x0, "GPK10"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "CCAP0_PIXCLK"),
+ MA35_MUX(0x8, "EBI_AD1"),
+ MA35_MUX(0xa, "EBI_ADR1")),
+ MA35_PIN(165, PK11, 0xd4, 0xc,
+ MA35_MUX(0x0, "GPK11"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "CCAP0_HSYNC"),
+ MA35_MUX(0x8, "EBI_AD2"),
+ MA35_MUX(0xa, "EBI_ADR2")),
+ MA35_PIN(166, PK12, 0xd4, 0x10,
+ MA35_MUX(0x0, "GPK12"),
+ MA35_MUX(0x1, "EPWM2_CH0"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x6, "SPI1_SS0"),
+ MA35_MUX(0x8, "SC0_CLK"),
+ MA35_MUX(0xb, "TM10"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(167, PK13, 0xd4, 0x14,
+ MA35_MUX(0x0, "GPK13"),
+ MA35_MUX(0x1, "EPWM2_CH1"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x6, "SPI1_CLK"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0xb, "TM10_EXT")),
+ MA35_PIN(168, PK14, 0xd4, 0x18,
+ MA35_MUX(0x0, "GPK14"),
+ MA35_MUX(0x1, "EPWM2_CH2"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "SPI1_MOSI"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0xa, "I2C5_SDA"),
+ MA35_MUX(0xb, "TM11"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(169, PK15, 0xd4, 0x1c,
+ MA35_MUX(0x0, "GPK15"),
+ MA35_MUX(0x1, "EPWM2_CH3"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x6, "SPI1_MISO"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0xa, "I2C5_SCL"),
+ MA35_MUX(0xb, "TM11_EXT")),
+ MA35_PIN(170, PL0, 0xd8, 0x0,
+ MA35_MUX(0x0, "GPL0"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "QSPI1_MOSI1"),
+ MA35_MUX(0x7, "I2S0_LRCK"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0x9, "SC1_CLK"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "QEI1_A")),
+ MA35_PIN(171, PL1, 0xd8, 0x4,
+ MA35_MUX(0x0, "GPL1"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "QSPI1_MISO1"),
+ MA35_MUX(0x7, "I2S0_BCLK"),
+ MA35_MUX(0x8, "EBI_AD12"),
+ MA35_MUX(0x9, "SC1_DAT"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "QEI1_B")),
+ MA35_PIN(172, PL2, 0xd8, 0x8,
+ MA35_MUX(0x0, "GPL2"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "QSPI1_SS1"),
+ MA35_MUX(0x7, "I2S0_DI"),
+ MA35_MUX(0x8, "EBI_AD13"),
+ MA35_MUX(0x9, "SC1_RST"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xc, "QEI1_INDEX")),
+ MA35_PIN(173, PL3, 0xd8, 0xc,
+ MA35_MUX(0x0, "GPL3"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "QSPI1_CLK"),
+ MA35_MUX(0x7, "I2S0_DO"),
+ MA35_MUX(0x8, "EBI_AD14"),
+ MA35_MUX(0x9, "SC1_PWR"),
+ MA35_MUX(0xb, "TM7_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC0")),
+ MA35_PIN(174, PL4, 0xd8, 0x10,
+ MA35_MUX(0x0, "GPL4"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "QSPI1_MOSI0"),
+ MA35_MUX(0x7, "I2S0_MCLK"),
+ MA35_MUX(0x8, "EBI_nRD"),
+ MA35_MUX(0x9, "SC1_nCD"),
+ MA35_MUX(0xb, "TM9"),
+ MA35_MUX(0xc, "ECAP0_IC1")),
+ MA35_PIN(175, PL5, 0xd8, 0x14,
+ MA35_MUX(0x0, "GPL5"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "QSPI1_MISO0"),
+ MA35_MUX(0x7, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EBI_nWR"),
+ MA35_MUX(0x9, "SC0_nCD"),
+ MA35_MUX(0xb, "TM9_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC2")),
+ MA35_PIN(176, PL6, 0xd8, 0x18,
+ MA35_MUX(0x0, "GPL6"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "QSPI1_MOSI1"),
+ MA35_MUX(0x7, "TRACE_CLK"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0xb, "TM3"),
+ MA35_MUX(0xc, "ECAP1_IC0"),
+ MA35_MUX(0xd, "INT0")),
+ MA35_PIN(177, PL7, 0xd8, 0x1c,
+ MA35_MUX(0x0, "GPL7"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "QSPI1_MISO1"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xc, "ECAP1_IC1"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(178, PL8, 0xdc, 0x0,
+ MA35_MUX(0x0, "GPL8"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "EPWM0_CH4"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0x9, "SC0_CLK"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xc, "ECAP1_IC2"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(179, PL9, 0xdc, 0x4,
+ MA35_MUX(0x0, "GPL9"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "EPWM1_CH4"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0x9, "SC0_DAT"),
+ MA35_MUX(0xb, "TM4_EXT"),
+ MA35_MUX(0xc, "QEI0_A"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(180, PL10, 0xdc, 0x8,
+ MA35_MUX(0x0, "GPL10"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "EPWM0_CH5"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0x9, "SC0_RST"),
+ MA35_MUX(0xb, "EBI_nWRH"),
+ MA35_MUX(0xc, "QEI0_B")),
+ MA35_PIN(181, PL11, 0xdc, 0xc,
+ MA35_MUX(0x0, "GPL11"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "EPWM1_CH5"),
+ MA35_MUX(0x7, "I2S1_DO"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0x9, "SC0_PWR"),
+ MA35_MUX(0xb, "EBI_nWRL"),
+ MA35_MUX(0xc, "QEI0_INDEX")),
+ MA35_PIN(182, PL12, 0xdc, 0x10,
+ MA35_MUX(0x0, "GPL12"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART7_nCTS"),
+ MA35_MUX(0x3, "ECAP1_IC0"),
+ MA35_MUX(0x4, "UART14_RXD"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x7, "SC1_CLK"),
+ MA35_MUX(0x8, "EBI_AD0"),
+ MA35_MUX(0x9, "HSUSBH_PWREN"),
+ MA35_MUX(0xa, "I2C2_SDA"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "EPWM0_CH2"),
+ MA35_MUX(0xd, "EBI_AD11"),
+ MA35_MUX(0xe, "RGMII0_PPS"),
+ MA35_MUX(0xf, "RMII0_PPS")),
+ MA35_PIN(183, PL13, 0xdc, 0x14,
+ MA35_MUX(0x0, "GPL13"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART7_nRTS"),
+ MA35_MUX(0x3, "ECAP1_IC1"),
+ MA35_MUX(0x4, "UART14_TXD"),
+ MA35_MUX(0x5, "SPI0_CLK"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x7, "SC1_DAT"),
+ MA35_MUX(0x8, "EBI_AD1"),
+ MA35_MUX(0x9, "HSUSBH_OVC"),
+ MA35_MUX(0xa, "I2C2_SCL"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "EPWM0_CH3"),
+ MA35_MUX(0xd, "EBI_AD12"),
+ MA35_MUX(0xe, "RGMII1_PPS"),
+ MA35_MUX(0xf, "RMII1_PPS")),
+ MA35_PIN(184, PL14, 0xdc, 0x18,
+ MA35_MUX(0x0, "GPL14"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART7_RXD"),
+ MA35_MUX(0x4, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI0_MOSI"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x7, "SC1_RST"),
+ MA35_MUX(0x8, "EBI_AD2"),
+ MA35_MUX(0xb, "TM2"),
+ MA35_MUX(0xc, "INT0"),
+ MA35_MUX(0xd, "EBI_AD13")),
+ MA35_PIN(185, PL15, 0xdc, 0x1c,
+ MA35_MUX(0x0, "GPL15"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART7_TXD"),
+ MA35_MUX(0x3, "TRACE_CLK"),
+ MA35_MUX(0x4, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI0_MISO"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x7, "SC1_PWR"),
+ MA35_MUX(0x8, "EBI_AD3"),
+ MA35_MUX(0xb, "TM2_EXT"),
+ MA35_MUX(0xc, "INT2"),
+ MA35_MUX(0xd, "EBI_AD14")),
+ MA35_PIN(186, PM0, 0xe0, 0x0,
+ MA35_MUX(0x0, "GPM0"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "CCAP0_VSYNC"),
+ MA35_MUX(0x8, "EBI_AD3"),
+ MA35_MUX(0xa, "EBI_ADR3")),
+ MA35_PIN(187, PM1, 0xe0, 0x4,
+ MA35_MUX(0x0, "GPM1"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI3_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP0_SFIELD"),
+ MA35_MUX(0x8, "EBI_AD4"),
+ MA35_MUX(0xa, "EBI_ADR4")),
+ MA35_PIN(188, PM2, 0xe0, 0x8,
+ MA35_MUX(0x0, "GPM2"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "CCAP0_DATA0"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0xa, "EBI_ADR5")),
+ MA35_PIN(189, PM3, 0xe0, 0xc,
+ MA35_MUX(0x0, "GPM3"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "CCAP0_DATA1"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0xa, "EBI_ADR6")),
+ MA35_PIN(190, PM4, 0xe0, 0x10,
+ MA35_MUX(0x0, "GPM4"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP0_DATA2"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0xa, "EBI_ADR7")),
+ MA35_PIN(191, PM5, 0xe0, 0x14,
+ MA35_MUX(0x0, "GPM5"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP0_DATA3"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0xa, "EBI_ADR8")),
+ MA35_PIN(192, PM6, 0xe0, 0x18,
+ MA35_MUX(0x0, "GPM6"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "CCAP0_DATA4"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0xa, "EBI_ADR9")),
+ MA35_PIN(193, PM7, 0xe0, 0x1c,
+ MA35_MUX(0x0, "GPM7"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "CCAP0_DATA5"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0xa, "EBI_ADR10")),
+ MA35_PIN(194, PM8, 0xe4, 0x0,
+ MA35_MUX(0x0, "GPM8"),
+ MA35_MUX(0x4, "I2C0_SDA"),
+ MA35_MUX(0x6, "CCAP0_DATA6"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0xa, "EBI_ADR11")),
+ MA35_PIN(195, PM9, 0xe4, 0x4,
+ MA35_MUX(0x0, "GPM9"),
+ MA35_MUX(0x4, "I2C0_SCL"),
+ MA35_MUX(0x6, "CCAP0_DATA7"),
+ MA35_MUX(0x8, "EBI_AD12"),
+ MA35_MUX(0xa, "EBI_ADR12")),
+ MA35_PIN(196, PM10, 0xe4, 0x8,
+ MA35_MUX(0x0, "GPM10"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "CCAP0_DATA8"),
+ MA35_MUX(0x7, "SPI2_I2SMCLK"),
+ MA35_MUX(0x8, "EBI_AD13"),
+ MA35_MUX(0xa, "EBI_ADR13")),
+ MA35_PIN(197, PM11, 0xe4, 0xc,
+ MA35_MUX(0x0, "GPM11"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x5, "SPI3_SS1"),
+ MA35_MUX(0x6, "CCAP0_DATA9"),
+ MA35_MUX(0x7, "SPI2_SS1"),
+ MA35_MUX(0x8, "EBI_AD14"),
+ MA35_MUX(0xa, "EBI_ADR14")),
+ MA35_PIN(198, PM12, 0xe4, 0x10,
+ MA35_MUX(0x0, "GPM12"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART10_nCTS"),
+ MA35_MUX(0x3, "TRACE_DATA0"),
+ MA35_MUX(0x4, "UART11_RXD"),
+ MA35_MUX(0x5, "I2C2_SDA"),
+ MA35_MUX(0x7, "SC1_nCD"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0x9, "I2S1_MCLK"),
+ MA35_MUX(0xb, "TM8")),
+ MA35_PIN(199, PM13, 0xe4, 0x14,
+ MA35_MUX(0x0, "GPM13"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART10_nRTS"),
+ MA35_MUX(0x3, "TRACE_DATA1"),
+ MA35_MUX(0x4, "UART11_TXD"),
+ MA35_MUX(0x5, "I2C2_SCL"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0x9, "ECAP1_IC0"),
+ MA35_MUX(0xb, "TM8_EXT")),
+ MA35_PIN(200, PM14, 0xe4, 0x18,
+ MA35_MUX(0x0, "GPM14"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART10_RXD"),
+ MA35_MUX(0x3, "TRACE_DATA2"),
+ MA35_MUX(0x4, "CAN2_RXD"),
+ MA35_MUX(0x6, "I2C3_SDA"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0x9, "ECAP1_IC1"),
+ MA35_MUX(0xb, "TM10"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(201, PM15, 0xe4, 0x1c,
+ MA35_MUX(0x0, "GPM15"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART10_TXD"),
+ MA35_MUX(0x3, "TRACE_DATA3"),
+ MA35_MUX(0x4, "CAN2_TXD"),
+ MA35_MUX(0x6, "I2C3_SCL"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0x9, "ECAP1_IC2"),
+ MA35_MUX(0xb, "TM10_EXT"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(202, PN0, 0xe8, 0x0,
+ MA35_MUX(0x0, "GPN0"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x6, "CCAP1_DATA0")),
+ MA35_PIN(203, PN1, 0xe8, 0x4,
+ MA35_MUX(0x0, "GPN1"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x6, "CCAP1_DATA1")),
+ MA35_PIN(204, PN2, 0xe8, 0x8,
+ MA35_MUX(0x0, "GPN2"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "CCAP1_DATA2")),
+ MA35_PIN(205, PN3, 0xe8, 0xc,
+ MA35_MUX(0x0, "GPN3"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "CCAP1_DATA3")),
+ MA35_PIN(206, PN4, 0xe8, 0x10,
+ MA35_MUX(0x0, "GPN4"),
+ MA35_MUX(0x4, "I2C1_SDA"),
+ MA35_MUX(0x6, "CCAP1_DATA4")),
+ MA35_PIN(207, PN5, 0xe8, 0x14,
+ MA35_MUX(0x0, "GPN5"),
+ MA35_MUX(0x4, "I2C1_SCL"),
+ MA35_MUX(0x6, "CCAP1_DATA5")),
+ MA35_PIN(208, PN6, 0xe8, 0x18,
+ MA35_MUX(0x0, "GPN6"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "CCAP1_DATA6")),
+ MA35_PIN(209, PN7, 0xe8, 0x1c,
+ MA35_MUX(0x0, "GPN7"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "CCAP1_DATA7")),
+ MA35_PIN(210, PN10, 0xec, 0x8,
+ MA35_MUX(0x0, "GPN10"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x6, "CCAP1_SCLK")),
+ MA35_PIN(211, PN11, 0xec, 0xc,
+ MA35_MUX(0x0, "GPN11"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x6, "CCAP1_PIXCLK")),
+ MA35_PIN(212, PN12, 0xec, 0x10,
+ MA35_MUX(0x0, "GPN12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP1_HSYNC")),
+ MA35_PIN(213, PN13, 0xec, 0x14,
+ MA35_MUX(0x0, "GPN13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP1_VSYNC")),
+ MA35_PIN(214, PN14, 0xec, 0x18,
+ MA35_MUX(0x0, "GPN14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI1_SS1"),
+ MA35_MUX(0x6, "CCAP1_SFIELD"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK")),
+ MA35_PIN(215, PN15, 0xec, 0x1c,
+ MA35_MUX(0x0, "GPN15"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "SPI1_SS1"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK"),
+ MA35_MUX(0x8, "SC0_nCD"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xa, "CLKO"),
+ MA35_MUX(0xb, "TM6")),
+ MA35_PIN(216, PN8, 0xec, 0x0,
+ MA35_MUX(0x0, "GPN8"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x4, "I2C0_SDA"),
+ MA35_MUX(0x5, "SPI2_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP1_DATA8")),
+ MA35_PIN(217, PN9, 0xec, 0x4,
+ MA35_MUX(0x0, "GPN9"),
+ MA35_MUX(0x1, "EPWM2_CH5"),
+ MA35_MUX(0x4, "I2C0_SCL"),
+ MA35_MUX(0x5, "SPI1_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP1_DATA9")),
+ MA35_PIN(218, PN10, 0xec, 0x8,
+ MA35_MUX(0x0, "GPN10"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x4, "USBHL2_DM"),
+ MA35_MUX(0x6, "CCAP1_SCLK")),
+ MA35_PIN(219, PN11, 0xec, 0xc,
+ MA35_MUX(0x0, "GPN11"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x4, "USBHL2_DP"),
+ MA35_MUX(0x6, "CCAP1_PIXCLK")),
+ MA35_PIN(220, PN12, 0xec, 0x10,
+ MA35_MUX(0x0, "GPN12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP1_HSYNC")),
+ MA35_PIN(221, PN13, 0xec, 0x14,
+ MA35_MUX(0x0, "GPN13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP1_VSYNC")),
+ MA35_PIN(222, PN14, 0xec, 0x18,
+ MA35_MUX(0x0, "GPN14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x4, "USBHL3_DM"),
+ MA35_MUX(0x5, "SPI1_SS1"),
+ MA35_MUX(0x6, "CCAP1_SFIELD"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK")),
+ MA35_PIN(223, PN15, 0xec, 0x1c,
+ MA35_MUX(0x0, "GPN15"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x4, "USBHL3_DP"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "SPI1_SS1"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK"),
+ MA35_MUX(0x8, "SC0_nCD"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xa, "CLKO"),
+ MA35_MUX(0xb, "TM6")),
+};
+
+static int ma35d1_get_pin_num(int offset, int shift)
+{
+ return (offset - 0x80) * 2 + shift / 4;
+}
+
+static struct ma35_pinctrl_soc_info ma35d1_pinctrl_info = {
+ .pins = ma35d1_pins,
+ .npins = ARRAY_SIZE(ma35d1_pins),
+ .get_pin_num = ma35d1_get_pin_num,
+};
+
+static const struct dev_pm_ops ma35d1_pinctrl_pm_ops = {
+ SET_LATE_SYSTEM_SLEEP_PM_OPS(ma35_pinctrl_suspend, ma35_pinctrl_resume)
+};
+
+static int ma35d1_pinctrl_probe(struct platform_device *pdev)
+{
+ return ma35_pinctrl_probe(pdev, &ma35d1_pinctrl_info);
+}
+
+static const struct of_device_id ma35d1_pinctrl_of_match[] = {
+ { .compatible = "nuvoton,ma35d1-pinctrl", },
+ { },
+};
+
+static struct platform_driver ma35d1_pinctrl_driver = {
+ .probe = ma35d1_pinctrl_probe,
+ .driver = {
+ .name = "ma35d1-pinctrl",
+ .pm = &ma35d1_pinctrl_pm_ops,
+ .of_match_table = ma35d1_pinctrl_of_match,
+ },
+};
+
+static int __init ma35d1_pinctrl_init(void)
+{
+ return platform_driver_register(&ma35d1_pinctrl_driver);
+}
+arch_initcall(ma35d1_pinctrl_init);
+
+MODULE_AUTHOR("schung@nuvoton.com");
+MODULE_DESCRIPTION("Nuvoton MA35D1 pinctrl driver");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
@ 2024-03-13 3:57 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 3:57 UTC (permalink / raw)
To: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer
Cc: linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
From: Jacky Huang <ychuang3@nuvoton.com>
Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
add support for ma35d1 pinctrl.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
---
drivers/pinctrl/nuvoton/Kconfig | 19 +
drivers/pinctrl/nuvoton/Makefile | 2 +
drivers/pinctrl/nuvoton/pinctrl-ma35.c | 1211 +++++++++++++++
drivers/pinctrl/nuvoton/pinctrl-ma35.h | 51 +
drivers/pinctrl/nuvoton/pinctrl-ma35d1.c | 1797 ++++++++++++++++++++++
5 files changed, 3080 insertions(+)
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.c
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.h
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
diff --git a/drivers/pinctrl/nuvoton/Kconfig b/drivers/pinctrl/nuvoton/Kconfig
index 2abbfcec1fae..7eadaaf48d6e 100644
--- a/drivers/pinctrl/nuvoton/Kconfig
+++ b/drivers/pinctrl/nuvoton/Kconfig
@@ -45,3 +45,22 @@ config PINCTRL_NPCM8XX
Say Y or M here to enable pin controller and GPIO support for
the Nuvoton NPCM8XX SoC. This is strongly recommended when
building a kernel that will run on this chip.
+
+config PINCTRL_MA35
+ bool
+ depends on (ARCH_MA35 || COMPILE_TEST) && OF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GENERIC_PINCONF
+ select GPIOLIB
+ select GPIO_GENERIC
+ select GPIOLIB_IRQCHIP
+ select MFD_SYSCON
+
+config PINCTRL_MA35D1
+ bool "Pinctrl and GPIO driver for Nuvoton MA35D1"
+ depends on (ARCH_MA35 || COMPILE_TEST) && OF
+ select PINCTRL_MA35
+ help
+ Say Y here to enable pin controller and GPIO support
+ for Nuvoton MA35D1 SoC.
diff --git a/drivers/pinctrl/nuvoton/Makefile b/drivers/pinctrl/nuvoton/Makefile
index 08031eab0af6..346c5082bc60 100644
--- a/drivers/pinctrl/nuvoton/Makefile
+++ b/drivers/pinctrl/nuvoton/Makefile
@@ -4,3 +4,5 @@
obj-$(CONFIG_PINCTRL_WPCM450) += pinctrl-wpcm450.o
obj-$(CONFIG_PINCTRL_NPCM7XX) += pinctrl-npcm7xx.o
obj-$(CONFIG_PINCTRL_NPCM8XX) += pinctrl-npcm8xx.o
+obj-$(CONFIG_PINCTRL_MA35) += pinctrl-ma35.o
+obj-$(CONFIG_PINCTRL_MA35D1) += pinctrl-ma35d1.o
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35.c b/drivers/pinctrl/nuvoton/pinctrl-ma35.c
new file mode 100644
index 000000000000..8efbe559be1e
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35.c
@@ -0,0 +1,1211 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <schung@nuvoton.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio/driver.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "../core.h"
+#include "../pinconf.h"
+#include "pinctrl-ma35.h"
+
+#define MA35_MFP_REG_BASE 0x80
+#define MA35_MFP_REG_SZ_PER_BANK 8
+#define MA35_MFP_BITS_PER_PORT 4
+
+#define MA35_GPIO_BANK_MAX 14
+#define MA35_GPIO_PORT_MAX 16
+
+/* GPIO control registers */
+#define MA35_GP_REG_MODE 0x00
+#define MA35_GP_REG_DINOFF 0x04
+#define MA35_GP_REG_DOUT 0x08
+#define MA35_GP_REG_DATMSK 0x0c
+#define MA35_GP_REG_PIN 0x10
+#define MA35_GP_REG_DBEN 0x14
+#define MA35_GP_REG_INTTYPE 0x18
+#define MA35_GP_REG_INTEN 0x1c
+#define MA35_GP_REG_INTSRC 0x20
+#define MA35_GP_REG_SMTEN 0x24
+#define MA35_GP_REG_SLEWCTL 0x28
+#define MA35_GP_REG_SPW 0x2c
+#define MA35_GP_REG_PUSEL 0x30
+#define MA35_GP_REG_DSL 0x38
+#define MA35_GP_REG_DSH 0x3c
+
+/* GPIO mode control */
+#define MA35_GP_MODE_INPUT 0x0
+#define MA35_GP_MODE_OUTPUT 0x1
+#define MA35_GP_MODE_OPEN_DRAIN 0x2
+#define MA35_GP_MODE_QUASI 0x3
+
+/* GPIO pull-up and pull-down selection control */
+#define MA35_GP_PUSEL_DISABLE 0x0
+#define MA35_GP_PUSEL_PULL_UP 0x1
+#define MA35_GP_PUSEL_PULL_DOWN 0x2
+
+/* Each pin data input/output is mapped by address mapping */
+#define MA35_PIN_MAP_BASE 0x800
+#define MA35_GP_DSH_BASE_PORT 8
+
+#define MVOLT_1800 0
+#define MVOLT_3300 1
+
+static const char * const gpio_group_name[] = {
+ "gpioa", "gpiob", "gpioc", "gpiod", "gpioe", "gpiof", "gpiog",
+ "gpioh", "gpioi", "gpioj", "gpiok", "gpiol", "gpiom", "gpion",
+};
+
+static const u32 ds_1800mv_tbl[] = {
+ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000,
+};
+
+static const u32 ds_3300mv_tbl[] = {
+ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000,
+};
+
+struct ma35_pin_func {
+ const char *name;
+ const char **groups;
+ u32 ngroups;
+};
+
+struct ma35_pin_setting {
+ u32 offset;
+ u32 shift;
+ u32 muxval;
+ unsigned long *configs;
+ unsigned int nconfigs;
+};
+
+struct ma35_pin_group {
+ const char *name;
+ unsigned int npins;
+ unsigned int *pins;
+ struct ma35_pin_setting *settings;
+};
+
+struct ma35_pin_bank {
+ void __iomem *reg_base;
+ struct clk *clk;
+ int irq;
+ u8 nr_pins;
+ const char *name;
+ u8 bank_num;
+ bool valid;
+ struct device_node *np;
+ struct gpio_chip chip;
+ u32 irqtype;
+ u32 irqinten;
+ struct regmap *regmap;
+ struct device *dev;
+ spinlock_t lock;
+};
+
+struct ma35_pin_ctrl {
+ struct ma35_pin_bank *pin_banks;
+ u32 nr_banks;
+ u32 nr_pins;
+};
+
+struct ma35_pinctrl {
+ struct device *dev;
+ struct ma35_pin_ctrl *ctrl;
+ struct pinctrl_dev *pctl;
+ const struct ma35_pinctrl_soc_info *info;
+ struct regmap *regmap;
+ struct ma35_pin_group *groups;
+ unsigned int ngroups;
+ struct ma35_pin_func *functions;
+ unsigned int nfunctions;
+};
+
+static int ma35_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->ngroups;
+}
+
+static const char *ma35_get_group_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->groups[selector].name;
+}
+
+static int ma35_get_group_pins(struct pinctrl_dev *pctldev, unsigned int selector,
+ const unsigned int **pins, unsigned int *npins)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ if (selector >= npctl->ngroups)
+ return -EINVAL;
+
+ *pins = npctl->groups[selector].pins;
+ *npins = npctl->groups[selector].npins;
+
+ return 0;
+}
+
+static struct ma35_pin_group *ma35_pinctrl_find_group_by_name(
+ const struct ma35_pinctrl *npctl, const char *name)
+{
+ int i;
+
+ for (i = 0; i < npctl->ngroups; i++) {
+ if (!strcmp(npctl->groups[i].name, name))
+ return &npctl->groups[i];
+ }
+ return NULL;
+}
+
+static int ma35_pinctrl_dt_node_to_map_func(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned int *num_maps)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ struct ma35_pin_group *grp;
+ struct pinctrl_map *new_map;
+ struct device_node *parent;
+ int map_num = 1;
+ int i;
+
+ /*
+ * first find the group of this node and check if we need create
+ * config maps for pins
+ */
+ grp = ma35_pinctrl_find_group_by_name(npctl, np->name);
+ if (!grp) {
+ dev_err(npctl->dev, "unable to find group for node %s\n", np->name);
+ return -EINVAL;
+ }
+
+ map_num += grp->npins;
+ new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map), GFP_KERNEL);
+ if (!new_map)
+ return -ENOMEM;
+
+ *map = new_map;
+ *num_maps = map_num;
+ /* create mux map */
+ parent = of_get_parent(np);
+ if (!parent) {
+ devm_kfree(pctldev->dev, new_map);
+ return -EINVAL;
+ }
+
+ new_map[0].type = PIN_MAP_TYPE_MUX_GROUP;
+ new_map[0].data.mux.function = parent->name;
+ new_map[0].data.mux.group = np->name;
+ of_node_put(parent);
+
+ new_map++;
+ for (i = 0; i < grp->npins; i++) {
+ new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN;
+ new_map[i].data.configs.group_or_pin = pin_get_name(pctldev, grp->pins[i]);
+ new_map[i].data.configs.configs = grp->settings[i].configs;
+ new_map[i].data.configs.num_configs = grp->settings[i].nconfigs;
+ }
+ dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
+ (*map)->data.mux.function, (*map)->data.mux.group, map_num);
+
+ return 0;
+}
+
+static const struct pinctrl_ops ma35_pctrl_ops = {
+ .get_groups_count = ma35_get_groups_count,
+ .get_group_name = ma35_get_group_name,
+ .get_group_pins = ma35_get_group_pins,
+ .dt_node_to_map = ma35_pinctrl_dt_node_to_map_func,
+ .dt_free_map = pinconf_generic_dt_free_map,
+};
+
+static int ma35_pinmux_get_func_count(struct pinctrl_dev *pctldev)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->nfunctions;
+}
+
+static const char *ma35_pinmux_get_func_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->functions[selector].name;
+}
+
+static int ma35_pinmux_get_func_groups(struct pinctrl_dev *pctldev,
+ unsigned int function,
+ const char *const **groups,
+ unsigned int *const num_groups)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = npctl->functions[function].groups;
+ *num_groups = npctl->functions[function].ngroups;
+
+ return 0;
+}
+
+static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
+ unsigned int group)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ struct ma35_pin_group *grp = &npctl->groups[group];
+ struct ma35_pin_setting *setting = grp->settings;
+ u32 i, regval;
+
+ dev_dbg(npctl->dev, "enable function %s group %s\n",
+ npctl->functions[selector].name, npctl->groups[group].name);
+
+ for (i = 0; i < grp->npins; i++) {
+ regmap_read(npctl->regmap, setting->offset, ®val);
+ regval &= ~GENMASK(setting->shift + 3, setting->shift);
+ regval |= setting->muxval << setting->shift;
+ regmap_write(npctl->regmap, setting->offset, regval);
+ setting++;
+ }
+ return 0;
+}
+
+static const struct pinmux_ops ma35_pmx_ops = {
+ .get_functions_count = ma35_pinmux_get_func_count,
+ .get_function_name = ma35_pinmux_get_func_name,
+ .get_function_groups = ma35_pinmux_get_func_groups,
+ .set_mux = ma35_pinmux_set_mux,
+ .strict = true,
+};
+
+static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
+ unsigned long flags;
+ unsigned int regval;
+
+ spin_lock_irqsave(&bank->lock, flags);
+
+ regval = readl(reg_mode);
+ regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
+ regval |= MA35_GP_MODE_INPUT << gpio * 2;
+ writel(regval, reg_mode);
+
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+
+ return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
+}
+
+static void ma35_gpio_core_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+
+ writel(val, bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
+}
+
+static int ma35_gpio_core_direction_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ void __iomem *reg_dout = bank->reg_base + MA35_GP_REG_DOUT;
+ void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
+ unsigned long flags;
+ unsigned int regval;
+
+ spin_lock_irqsave(&bank->lock, flags);
+
+ regval = readl(reg_dout);
+ if (val)
+ writel(regval | BIT(gpio), reg_dout);
+ else
+ writel(regval & ~BIT(gpio), reg_dout);
+
+ regval = readl(reg_mode);
+ regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
+ regval |= MA35_GP_MODE_OUTPUT << gpio * 2;
+ writel(regval, reg_mode);
+
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int ma35_gpio_core_to_request(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ u32 reg_offs, bit_offs, regval;
+
+ if (gpio < 8) {
+ /* The MFP low register controls port 0 ~ 7 */
+ reg_offs = bank->bank_num * MA35_MFP_REG_SZ_PER_BANK;
+ bit_offs = gpio * MA35_MFP_BITS_PER_PORT;
+ } else {
+ /* The MFP high register controls port 8 ~ 15 */
+ reg_offs = bank->bank_num * MA35_MFP_REG_SZ_PER_BANK + 4;
+ bit_offs = (gpio - 8) * MA35_MFP_BITS_PER_PORT;
+ }
+
+ regmap_read(bank->regmap, MA35_MFP_REG_BASE + reg_offs, ®val);
+ regval &= ~GENMASK(bit_offs + MA35_MFP_BITS_PER_PORT - 1, bit_offs);
+ regmap_write(bank->regmap, MA35_MFP_REG_BASE + reg_offs, regval);
+
+ return 0;
+}
+
+static void ma35_irq_gpio_mask(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+ u32 regval;
+
+ regval = readl(reg_ien);
+
+ /*
+ * The MA35_GP_REG_INTEN bits 0 ~ 15 control low-level or falling edge trigger,
+ * while bits 16 ~ 31 control high-level or rising edge trigger.
+ * We disable both type of interrupt.
+ */
+ regval &= ~(BIT(num + 16) | BIT(num));
+
+ writel(regval, reg_ien);
+}
+
+static void ma35_irq_gpio_unmask(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+ u32 bval, regval;
+
+ bval = bank->irqtype & BIT(num);
+
+ regval = readl(reg_itype);
+ regval &= ~BIT(num);
+ writel(regval | bval, reg_itype);
+
+ bval = bank->irqinten & (BIT(num + 16) | BIT(num));
+
+ regval = readl(reg_ien);
+ regval &= ~(BIT(num + 16) | BIT(num));
+ writel(regval | bval, reg_ien);
+}
+
+static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+
+ if (type == IRQ_TYPE_PROBE) {
+ writel(readl(reg_itype) & ~BIT(num), reg_itype);
+ writel(readl(reg_ien) | BIT(num) | BIT(num + 16), reg_ien);
+ bank->irqtype &= ~BIT(num);
+ bank->irqinten |= BIT(num) | BIT(num + 16);
+ return 0;
+ }
+
+ if (type & IRQ_TYPE_LEVEL_MASK) {
+ writel(readl(reg_itype) | BIT(num), reg_itype);
+ writel(readl(reg_ien) & ~(BIT(num) | BIT(num + 16)), reg_ien);
+ bank->irqtype |= BIT(num);
+ bank->irqinten &= ~(BIT(num) | BIT(num + 16));
+ if (type == IRQ_TYPE_LEVEL_HIGH) {
+ writel(readl(reg_ien) | BIT(num + 16), reg_ien);
+ bank->irqinten |= BIT(num + 16);
+ return 0;
+ }
+
+ if (type == IRQ_TYPE_LEVEL_LOW) {
+ writel(readl(reg_ien) | BIT(num), reg_ien);
+ bank->irqinten |= BIT(num);
+ return 0;
+ }
+
+ } else {
+ writel(readl(reg_itype) & ~BIT(num), reg_itype);
+ bank->irqtype &= ~BIT(num);
+
+ if (type & IRQ_TYPE_EDGE_RISING) {
+ writel(readl(reg_ien) | BIT(num + 16), reg_ien);
+ bank->irqinten |= BIT(num + 16);
+
+ } else {
+ writel(readl(reg_ien) & ~BIT(num + 16), reg_ien);
+ bank->irqinten &= ~BIT(num + 16);
+ }
+
+ if (type & IRQ_TYPE_EDGE_FALLING) {
+ writel(readl(reg_ien) | BIT(num), reg_ien);
+ bank->irqinten |= BIT(num);
+
+ } else {
+ writel(readl(reg_ien) & ~BIT(num), reg_ien);
+ bank->irqinten &= ~BIT(num);
+ }
+ }
+ return 0;
+}
+
+static struct irq_chip ma35_gpio_irqchip = {
+ .name = "MA35-GPIO-IRQ",
+ .irq_disable = ma35_irq_gpio_mask,
+ .irq_enable = ma35_irq_gpio_unmask,
+ .irq_mask = ma35_irq_gpio_mask,
+ .irq_unmask = ma35_irq_gpio_unmask,
+ .irq_set_type = ma35_irq_irqtype,
+ .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE | IRQCHIP_IMMUTABLE,
+};
+
+static void ma35_irq_demux_intgroup(struct irq_desc *desc)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_desc_get_handler_data(desc));
+ struct irq_domain *irqdomain = bank->chip.irq.domain;
+ struct irq_chip *irqchip = irq_desc_get_chip(desc);
+ unsigned int j, isr;
+
+ chained_irq_enter(irqchip, desc);
+
+ isr = readl(bank->reg_base + MA35_GP_REG_INTSRC);
+
+ if (isr != 0) {
+ writel(isr, bank->reg_base + MA35_GP_REG_INTSRC);
+
+ for (j = 0; j < 16; j++) {
+ if (isr & 0x1)
+ generic_handle_irq(irq_find_mapping(irqdomain, j));
+ isr = isr >> 1;
+ }
+ }
+
+ chained_irq_exit(irqchip, desc);
+}
+
+static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
+{
+ struct ma35_pin_ctrl *ctrl = npctl->ctrl;
+ struct ma35_pin_bank *bank = ctrl->pin_banks;
+ int ret;
+ int i;
+
+ for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
+ if (!bank->valid) {
+ dev_warn(&pdev->dev, "bank %s is not valid\n",
+ bank->np->name);
+ continue;
+ }
+ bank->irqtype = 0;
+ bank->irqinten = 0;
+ bank->chip.label = bank->name;
+ bank->chip.of_gpio_n_cells = 2;
+ bank->chip.parent = &pdev->dev;
+ bank->chip.request = ma35_gpio_core_to_request;
+ bank->chip.direction_input = ma35_gpio_core_direction_in;
+ bank->chip.direction_output = ma35_gpio_core_direction_out;
+ bank->chip.get = ma35_gpio_core_get;
+ bank->chip.set = ma35_gpio_core_set;
+ bank->chip.base = -1;
+ bank->chip.ngpio = bank->nr_pins;
+ bank->chip.can_sleep = false;
+ spin_lock_init(&bank->lock);
+
+ if (bank->irq > 0) {
+ struct gpio_irq_chip *girq;
+
+ girq = &bank->chip.irq;
+ gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
+ girq->parent_handler = ma35_irq_demux_intgroup;
+ girq->num_parents = 1;
+
+ girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
+ GFP_KERNEL);
+ if (!girq->parents)
+ return -ENOMEM;
+
+ girq->parents[0] = bank->irq;
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_level_irq;
+ }
+
+ ret = gpiochip_add_data(&bank->chip, bank);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
+ bank->chip.label, ret);
+ goto fail;
+ }
+ }
+ return 0;
+
+fail:
+ for (--i, --bank; i >= 0; --i, --bank) {
+ if (!bank->valid)
+ continue;
+ gpiochip_remove(&bank->chip);
+ }
+ return ret;
+}
+
+static int ma35_get_bank_data(struct ma35_pin_bank *bank, struct ma35_pinctrl *npctl)
+{
+ struct resource res;
+
+ if (of_address_to_resource(bank->np, 0, &res)) {
+ dev_err(npctl->dev, "cannot find IO resource for bank\n");
+ return -ENOENT;
+ }
+
+ bank->reg_base = devm_ioremap_resource(npctl->dev, &res);
+ if (IS_ERR(bank->reg_base)) {
+ dev_err(npctl->dev, "cannot ioremap resource for bank\n");
+ return PTR_ERR(bank->reg_base);
+ }
+
+ bank->irq = irq_of_parse_and_map(bank->np, 0);
+ bank->nr_pins = MA35_GPIO_PORT_MAX;
+
+ bank->clk = of_clk_get(bank->np, 0);
+ if (IS_ERR(bank->clk))
+ return PTR_ERR(bank->clk);
+
+ return clk_prepare_enable(bank->clk);
+}
+
+static int ma35_pinctrl_get_soc_data(struct ma35_pinctrl *pctl, struct platform_device *pdev)
+{
+ struct fwnode_handle *child;
+ struct ma35_pin_ctrl *ctrl;
+ struct ma35_pin_bank *bank;
+ int i, id = 0;
+
+ ctrl = pctl->ctrl;
+ ctrl->nr_banks = MA35_GPIO_BANK_MAX;
+
+ ctrl->pin_banks = devm_kcalloc(&pdev->dev, ctrl->nr_banks,
+ sizeof(*ctrl->pin_banks), GFP_KERNEL);
+ if (!ctrl->pin_banks)
+ return -ENOMEM;
+
+ for (i = 0; i < ctrl->nr_banks; i++) {
+ ctrl->pin_banks[i].bank_num = i;
+ ctrl->pin_banks[i].name = gpio_group_name[i];
+ }
+
+ for_each_gpiochip_node(&pdev->dev, child) {
+ struct device_node *np = to_of_node(child);
+
+ bank = &ctrl->pin_banks[id];
+ bank->np = np;
+ bank->regmap = pctl->regmap;
+ bank->dev = &pdev->dev;
+ if (!ma35_get_bank_data(bank, pctl))
+ bank->valid = true;
+ id++;
+ }
+ return 0;
+}
+
+static void ma35_gpio_cla_port(unsigned int gpio_num, unsigned int *group,
+ unsigned int *num)
+{
+ *group = gpio_num / MA35_GPIO_PORT_MAX;
+ *num = gpio_num % MA35_GPIO_PORT_MAX;
+}
+
+static int ma35_pinconf_set_pull(struct ma35_pinctrl *npctl, unsigned int pin,
+ int pull_up)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_PUSEL);
+ regval &= ~GENMASK(port * 2 + 1, port * 2);
+
+ switch (pull_up) {
+ case PIN_CONFIG_BIAS_PULL_UP:
+ regval |= MA35_GP_PUSEL_PULL_UP << port * 2;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ regval |= MA35_GP_PUSEL_PULL_DOWN << port * 2;
+ break;
+
+ case MA35_GP_PUSEL_DISABLE:
+ regval |= MA35_GP_PUSEL_DISABLE << port * 2;
+ break;
+
+ default:
+ regval |= MA35_GP_PUSEL_DISABLE << port * 2;
+ break;
+ }
+ writel(regval, base + MA35_GP_REG_PUSEL);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_output(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval, mode;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_MODE);
+ mode = (regval & GENMASK(port * 2 + 1, port * 2)) >> port * 2;
+
+ if (mode == MA35_GP_MODE_OUTPUT)
+ return 1;
+
+ return 0;
+}
+
+static int ma35_pinconf_get_pull(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval, mode;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_PUSEL);
+ mode = (regval & GENMASK(port * 2 + 1, port * 2)) >> port * 2;
+
+ switch (mode) {
+ case MA35_GP_PUSEL_PULL_UP:
+ return PIN_CONFIG_BIAS_PULL_UP;
+
+ case MA35_GP_PUSEL_PULL_DOWN:
+ return PIN_CONFIG_BIAS_PULL_DOWN;
+
+ case MA35_GP_PUSEL_DISABLE:
+ return PIN_CONFIG_BIAS_DISABLE;
+ }
+
+ return PIN_CONFIG_BIAS_DISABLE;
+}
+
+static int ma35_pinconf_set_output(struct ma35_pinctrl *npctl, unsigned int pin, bool out)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_MODE);
+ regval &= ~GENMASK(port * 2 + 1, port * 2);
+ regval |= MA35_GP_MODE_OUTPUT << port * 2;
+ writel(regval, base + MA35_GP_REG_MODE);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_power_source(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SPW);
+
+ if (regval & BIT(port))
+ return MVOLT_3300;
+ else
+ return MVOLT_1800;
+}
+
+static int ma35_pinconf_set_power_source(struct ma35_pinctrl *npctl,
+ unsigned int pin, int arg)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ if ((arg != MVOLT_1800) && (arg != MVOLT_3300))
+ return -EINVAL;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SPW);
+
+ if (arg == MVOLT_1800)
+ regval &= ~BIT(port);
+ else
+ regval |= BIT(port);
+
+ writel(regval, base + MA35_GP_REG_SPW);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_drive_strength(struct ma35_pinctrl *npctl, unsigned int pin,
+ u32 *strength)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval, ds_val;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ if (port < MA35_GP_DSH_BASE_PORT) {
+ regval = readl(base + MA35_GP_REG_DSL);
+ ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
+ } else {
+ port -= MA35_GP_DSH_BASE_PORT;
+ regval = readl(base + MA35_GP_REG_DSH);
+ ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
+ }
+
+ if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800)
+ *strength = ds_1800mv_tbl[ds_val];
+ else
+ *strength = ds_3300mv_tbl[ds_val];
+
+ return 0;
+}
+
+static int ma35_pinconf_set_drive_strength(struct ma35_pinctrl *npctl, unsigned int pin,
+ int strength)
+{
+ int port, group_num;
+ void __iomem *base;
+ int i, ds_val = -1;
+ u32 regval;
+
+ if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800) {
+ for (i = 0; i < ARRAY_SIZE(ds_1800mv_tbl); i++) {
+ if (ds_1800mv_tbl[i] == strength)
+ ds_val = i;
+ }
+ } else {
+ for (i = 0; i < ARRAY_SIZE(ds_3300mv_tbl); i++) {
+ if (ds_3300mv_tbl[i] == strength)
+ ds_val = i;
+ }
+ }
+ if (ds_val == -1)
+ return -EINVAL;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ if (port < MA35_GP_DSH_BASE_PORT) {
+ regval = readl(base + MA35_GP_REG_DSL);
+ regval &= ~GENMASK(port * 4 + 2, port * 4);
+ regval |= ds_val << port * 4;
+ writel(regval, base + MA35_GP_REG_DSL);
+ } else {
+ port -= MA35_GP_DSH_BASE_PORT;
+ regval = readl(base + MA35_GP_REG_DSH);
+ regval &= ~GENMASK(port * 4 + 2, port * 4);
+ regval |= ds_val << port * 4;
+ writel(regval, base + MA35_GP_REG_DSH);
+ }
+ return 0;
+}
+
+static int ma35_pinconf_get_schmitt_enable(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SMTEN);
+
+ return !!(regval & BIT(port));
+}
+
+static int ma35_pinconf_set_schmitt(struct ma35_pinctrl *npctl, unsigned int pin, int enable)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SMTEN);
+
+ if (enable)
+ regval |= BIT(port);
+ else
+ regval &= ~BIT(port);
+
+ writel(regval, base + MA35_GP_REG_SMTEN);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_slew_rate(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SLEWCTL);
+
+ return (regval & GENMASK(port * 2 + 1, port * 2)) >> port * 2;
+}
+
+static int ma35_pinconf_set_slew_rate(struct ma35_pinctrl *npctl, unsigned int pin, int rate)
+{
+ int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SLEWCTL);
+ regval &= ~GENMASK(port * 2 + 1, port * 2);
+ regval |= rate << port * 2;
+ writel(regval, base + MA35_GP_REG_SLEWCTL);
+
+ return 0;
+}
+
+static int ma35_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param = pinconf_to_config_param(*config);
+ u32 arg;
+ int ret;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (ma35_pinconf_get_pull(npctl, pin) == param)
+ arg = 1;
+ else
+ return -EINVAL;
+ break;
+
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ ret = ma35_pinconf_get_drive_strength(npctl, pin, &arg);
+ if (ret)
+ return ret;
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ arg = ma35_pinconf_get_schmitt_enable(npctl, pin);
+ break;
+
+ case PIN_CONFIG_SLEW_RATE:
+ arg = ma35_pinconf_get_slew_rate(npctl, pin);
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ arg = ma35_pinconf_get_output(npctl, pin);
+ break;
+
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = ma35_pinconf_get_power_source(npctl, pin);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int ma35_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned int num_configs)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param;
+ unsigned int arg = 0;
+ int i, ret = 0;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ ret = ma35_pinconf_set_pull(npctl, pin, param);
+ break;
+
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ ret = ma35_pinconf_set_drive_strength(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ ret = ma35_pinconf_set_schmitt(npctl, pin, 1);
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT:
+ ret = ma35_pinconf_set_schmitt(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_SLEW_RATE:
+ ret = ma35_pinconf_set_slew_rate(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ ret = ma35_pinconf_set_output(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_POWER_SOURCE:
+ ret = ma35_pinconf_set_power_source(npctl, pin, arg);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ }
+ return ret;
+}
+
+static const struct pinconf_ops ma35_pinconf_ops = {
+ .pin_config_get = ma35_pinconf_get,
+ .pin_config_set = ma35_pinconf_set,
+ .is_generic = true,
+};
+
+static int ma35_pinctrl_parse_groups(struct device_node *np, struct ma35_pin_group *grp,
+ struct ma35_pinctrl *npctl, u32 index)
+{
+ unsigned long *configs;
+ unsigned int nconfigs;
+ struct ma35_pin_setting *pin;
+ const __be32 *list;
+ int i, j, size, ret;
+
+ dev_dbg(npctl->dev, "group(%d): %s\n", index, np->name);
+
+ grp->name = np->name;
+
+ ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &nconfigs);
+ if (ret)
+ return ret;
+
+ /*
+ * the binding format is nuvoton,pins = <bank pin-mfp pin-function>,
+ * do sanity check and calculate pins number
+ */
+ list = of_get_property(np, "nuvoton,pins", &size);
+ size /= sizeof(*list);
+ if (!size || size % 3) {
+ dev_err(npctl->dev, "wrong setting!\n");
+ return -EINVAL;
+ }
+ grp->npins = size / 3;
+
+ grp->pins = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
+ if (!grp->pins)
+ return -ENOMEM;
+
+ grp->settings = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->settings), GFP_KERNEL);
+ if (!grp->settings)
+ return -ENOMEM;
+
+ pin = grp->settings;
+
+ for (i = 0, j = 0; i < size; i += 3, j++) {
+ pin->offset = be32_to_cpu(*list++) * MA35_MFP_REG_SZ_PER_BANK + MA35_MFP_REG_BASE;
+ pin->shift = (be32_to_cpu(*list++) * MA35_MFP_BITS_PER_PORT) % 32;
+ pin->muxval = be32_to_cpu(*list++);
+ pin->configs = configs;
+ pin->nconfigs = nconfigs;
+ grp->pins[j] = npctl->info->get_pin_num(pin->offset, pin->shift);
+ pin++;
+ }
+ return 0;
+}
+
+static int ma35_pinctrl_parse_functions(struct device_node *np, struct ma35_pinctrl *npctl,
+ u32 index)
+{
+ struct device_node *child;
+ struct ma35_pin_func *func;
+ struct ma35_pin_group *grp;
+ static u32 grp_index;
+ u32 ret, i = 0;
+
+ dev_dbg(npctl->dev, "parse function(%d): %s\n", index, np->name);
+
+ func = &npctl->functions[index];
+ func->name = np->name;
+ func->ngroups = of_get_child_count(np);
+
+ if (func->ngroups <= 0)
+ return 0;
+
+ func->groups = devm_kcalloc(npctl->dev, func->ngroups, sizeof(char *), GFP_KERNEL);
+ if (!func->groups)
+ return -ENOMEM;
+
+ for_each_child_of_node(np, child) {
+ func->groups[i] = child->name;
+ grp = &npctl->groups[grp_index++];
+ ret = ma35_pinctrl_parse_groups(child, grp, npctl, i++);
+ if (ret) {
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static int ma35_pinctrl_probe_dt(struct platform_device *pdev, struct ma35_pinctrl *npctl)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+ u32 idx = 0;
+ int ret;
+
+ if (!np)
+ return -ENODEV;
+
+ for_each_child_of_node(np, child) {
+ if (of_property_read_bool(child, "gpio-controller"))
+ continue;
+ npctl->nfunctions++;
+ npctl->ngroups += of_get_child_count(child);
+ }
+
+ npctl->functions = devm_kcalloc(&pdev->dev, npctl->nfunctions,
+ sizeof(*npctl->functions), GFP_KERNEL);
+ if (!npctl->functions)
+ return -ENOMEM;
+
+ npctl->groups = devm_kcalloc(&pdev->dev, npctl->ngroups,
+ sizeof(*npctl->groups), GFP_KERNEL);
+ if (!npctl->groups)
+ return -ENOMEM;
+
+ dev_dbg(&pdev->dev, "nfunctions = %d\n", npctl->nfunctions);
+ dev_dbg(&pdev->dev, "ngroups = %d\n", npctl->ngroups);
+
+ for_each_child_of_node(np, child) {
+ if (of_property_read_bool(child, "gpio-controller"))
+ continue;
+
+ ret = ma35_pinctrl_parse_functions(child, npctl, idx++);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to parse function\n");
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+int ma35_pinctrl_probe(struct platform_device *pdev, const struct ma35_pinctrl_soc_info *info)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct pinctrl_desc *ma35_pinctrl_desc;
+ struct ma35_pinctrl *npctl;
+ int ret;
+
+ if (!info || !info->pins || !info->npins) {
+ dev_err(&pdev->dev, "wrong pinctrl info\n");
+ return -EINVAL;
+ }
+
+ npctl = devm_kzalloc(&pdev->dev, sizeof(*npctl), GFP_KERNEL);
+ if (!npctl)
+ return -ENOMEM;
+
+ ma35_pinctrl_desc = devm_kzalloc(&pdev->dev, sizeof(*ma35_pinctrl_desc), GFP_KERNEL);
+ if (!ma35_pinctrl_desc)
+ return -ENOMEM;
+
+ npctl->ctrl = devm_kzalloc(&pdev->dev, sizeof(*npctl->ctrl), GFP_KERNEL);
+ if (!npctl->ctrl)
+ return -ENOMEM;
+
+ ma35_pinctrl_desc->name = dev_name(&pdev->dev);
+ ma35_pinctrl_desc->pins = info->pins;
+ ma35_pinctrl_desc->npins = info->npins;
+ ma35_pinctrl_desc->pctlops = &ma35_pctrl_ops;
+ ma35_pinctrl_desc->pmxops = &ma35_pmx_ops;
+ ma35_pinctrl_desc->confops = &ma35_pinconf_ops;
+ ma35_pinctrl_desc->owner = THIS_MODULE;
+
+ npctl->info = info;
+ npctl->dev = &pdev->dev;
+
+ npctl->regmap = syscon_regmap_lookup_by_phandle(np, "nuvoton,sys");
+ if (IS_ERR(npctl->regmap))
+ return dev_err_probe(&pdev->dev, PTR_ERR(npctl->regmap),
+ "No syscfg phandle specified\n");
+
+ ma35_pinctrl_get_soc_data(npctl, pdev);
+
+ platform_set_drvdata(pdev, npctl);
+
+ ret = ma35_pinctrl_probe_dt(pdev, npctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to probe MA35 pinctrl dt\n");
+
+ ret = devm_pinctrl_register_and_init(&pdev->dev, ma35_pinctrl_desc,
+ npctl, &npctl->pctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to register MA35 pinctrl\n");
+
+ ret = pinctrl_enable(npctl->pctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to enable MA35 pinctrl\n");
+
+ return ma35_gpiolib_register(pdev, npctl);
+}
+
+int __maybe_unused ma35_pinctrl_suspend(struct device *dev)
+{
+ struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
+
+ return pinctrl_force_sleep(npctl->pctl);
+}
+
+int __maybe_unused ma35_pinctrl_resume(struct device *dev)
+{
+ struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
+
+ return pinctrl_force_default(npctl->pctl);
+}
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35.h b/drivers/pinctrl/nuvoton/pinctrl-ma35.h
new file mode 100644
index 000000000000..281605e2c231
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <schung@nuvoton.com>
+ */
+#ifndef __PINCTRL_MA35_H
+#define __PINCTRL_MA35_H
+
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+
+struct ma35_mux_desc {
+ const char *name;
+ u32 muxval;
+};
+
+struct ma35_pin_data {
+ u32 offset;
+ u32 shift;
+ struct ma35_mux_desc *muxes;
+};
+
+struct ma35_pinctrl_soc_info {
+ const struct pinctrl_pin_desc *pins;
+ unsigned int npins;
+ int (*get_pin_num)(int offset, int shift);
+};
+
+#define MA35_PIN(num, n, o, s, ...) { \
+ .number = num, \
+ .name = #n, \
+ .drv_data = &(struct ma35_pin_data) { \
+ .offset = o, \
+ .shift = s, \
+ .muxes = (struct ma35_mux_desc[]) { \
+ __VA_ARGS__, { } }, \
+ }, \
+}
+
+#define MA35_MUX(_val, _name) { \
+ .name = _name, \
+ .muxval = _val, \
+}
+
+int ma35_pinctrl_probe(struct platform_device *pdev, const struct ma35_pinctrl_soc_info *info);
+int ma35_pinctrl_suspend(struct device *dev);
+int ma35_pinctrl_resume(struct device *dev);
+
+#endif /* __PINCTRL_MA35_H */
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c b/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
new file mode 100644
index 000000000000..36510c0b0690
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
@@ -0,0 +1,1797 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <schung@nuvoton.com>
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-ma35.h"
+
+static const struct pinctrl_pin_desc ma35d1_pins[] = {
+ MA35_PIN(0, PA0, 0x80, 0x0,
+ MA35_MUX(0x0, "GPA0"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART16_RXD"),
+ MA35_MUX(0x6, "NAND_DATA0"),
+ MA35_MUX(0x7, "EBI_AD0"),
+ MA35_MUX(0x9, "EBI_ADR0")),
+ MA35_PIN(1, PA1, 0x80, 0x4,
+ MA35_MUX(0x0, "GPA1"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART16_TXD"),
+ MA35_MUX(0x6, "NAND_DATA1"),
+ MA35_MUX(0x7, "EBI_AD1"),
+ MA35_MUX(0x9, "EBI_ADR1")),
+ MA35_PIN(2, PA2, 0x80, 0x8,
+ MA35_MUX(0x0, "GPA2"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x6, "NAND_DATA2"),
+ MA35_MUX(0x7, "EBI_AD2"),
+ MA35_MUX(0x9, "EBI_ADR2")),
+ MA35_PIN(3, PA3, 0x80, 0xc,
+ MA35_MUX(0x0, "GPA3"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x6, "NAND_DATA3"),
+ MA35_MUX(0x7, "EBI_AD3"),
+ MA35_MUX(0x9, "EBI_ADR3")),
+ MA35_PIN(4, PA4, 0x80, 0x10,
+ MA35_MUX(0x0, "GPA4"),
+ MA35_MUX(0x2, "UART3_nCTS"),
+ MA35_MUX(0x3, "UART2_RXD"),
+ MA35_MUX(0x6, "NAND_DATA4"),
+ MA35_MUX(0x7, "EBI_AD4"),
+ MA35_MUX(0x9, "EBI_ADR4")),
+ MA35_PIN(5, PA5, 0x80, 0x14,
+ MA35_MUX(0x0, "GPA5"),
+ MA35_MUX(0x2, "UART3_nRTS"),
+ MA35_MUX(0x3, "UART2_TXD"),
+ MA35_MUX(0x6, "NAND_DATA5"),
+ MA35_MUX(0x7, "EBI_AD5"),
+ MA35_MUX(0x9, "EBI_ADR5")),
+ MA35_PIN(6, PA6, 0x80, 0x18,
+ MA35_MUX(0x0, "GPA6"),
+ MA35_MUX(0x2, "UART3_RXD"),
+ MA35_MUX(0x6, "NAND_DATA6"),
+ MA35_MUX(0x7, "EBI_AD6"),
+ MA35_MUX(0x9, "EBI_ADR6")),
+ MA35_PIN(7, PA7, 0x80, 0x1c,
+ MA35_MUX(0x0, "GPA7"),
+ MA35_MUX(0x2, "UART3_TXD"),
+ MA35_MUX(0x6, "NAND_DATA7"),
+ MA35_MUX(0x7, "EBI_AD7"),
+ MA35_MUX(0x9, "EBI_ADR7")),
+ MA35_PIN(8, PA8, 0x84, 0x0,
+ MA35_MUX(0x0, "GPA8"),
+ MA35_MUX(0x2, "UART5_nCTS"),
+ MA35_MUX(0x3, "UART4_RXD"),
+ MA35_MUX(0x6, "NAND_RDY0"),
+ MA35_MUX(0x7, "EBI_AD8"),
+ MA35_MUX(0x9, "EBI_ADR8")),
+ MA35_PIN(9, PA9, 0x84, 0x4,
+ MA35_MUX(0x0, "GPA9"),
+ MA35_MUX(0x2, "UART5_nRTS"),
+ MA35_MUX(0x3, "UART4_TXD"),
+ MA35_MUX(0x6, "NAND_nRE"),
+ MA35_MUX(0x7, "EBI_AD9"),
+ MA35_MUX(0x9, "EBI_ADR9")),
+ MA35_PIN(10, PA10, 0x84, 0x8,
+ MA35_MUX(0x0, "GPA10"),
+ MA35_MUX(0x2, "UART5_RXD"),
+ MA35_MUX(0x6, "NAND_nWE"),
+ MA35_MUX(0x7, "EBI_AD10"),
+ MA35_MUX(0x9, "EBI_ADR10")),
+ MA35_PIN(11, PA11, 0x84, 0xc,
+ MA35_MUX(0x0, "GPA11"),
+ MA35_MUX(0x2, "UART5_TXD"),
+ MA35_MUX(0x6, "NAND_CLE"),
+ MA35_MUX(0x7, "EBI_AD11"),
+ MA35_MUX(0x9, "EBI_ADR11")),
+ MA35_PIN(12, PA12, 0x84, 0x10,
+ MA35_MUX(0x0, "GPA12"),
+ MA35_MUX(0x2, "UART7_nCTS"),
+ MA35_MUX(0x3, "UART8_RXD"),
+ MA35_MUX(0x6, "NAND_ALE"),
+ MA35_MUX(0x7, "EBI_AD12"),
+ MA35_MUX(0x9, "EBI_ADR12")),
+ MA35_PIN(13, PA13, 0x84, 0x14,
+ MA35_MUX(0x0, "GPA13"),
+ MA35_MUX(0x2, "UART7_nRTS"),
+ MA35_MUX(0x3, "UART8_TXD"),
+ MA35_MUX(0x6, "NAND_nCS0"),
+ MA35_MUX(0x7, "EBI_AD13"),
+ MA35_MUX(0x9, "EBI_ADR13")),
+ MA35_PIN(14, PA14, 0x84, 0x18,
+ MA35_MUX(0x0, "GPA14"),
+ MA35_MUX(0x2, "UART7_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "NAND_nWP"),
+ MA35_MUX(0x7, "EBI_AD14"),
+ MA35_MUX(0x9, "EBI_ADR14")),
+ MA35_PIN(15, PA15, 0x84, 0x1c,
+ MA35_MUX(0x0, "GPA15"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART9_nCTS"),
+ MA35_MUX(0x3, "UART6_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "CAN2_RXD"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0x9, "QEI0_A"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xe, "RGMII0_PPS"),
+ MA35_MUX(0xf, "RMII0_PPS")),
+ MA35_PIN(16, PB0, 0x88, 0x0,
+ MA35_MUX(0x0, "GPB0"),
+ MA35_MUX(0x8, "EADC0_CH0")),
+ MA35_PIN(17, PB1, 0x88, 0x4,
+ MA35_MUX(0x0, "GPB1"),
+ MA35_MUX(0x8, "EADC0_CH1")),
+ MA35_PIN(18, PB2, 0x88, 0x8,
+ MA35_MUX(0x0, "GPB2"),
+ MA35_MUX(0x8, "EADC0_CH2")),
+ MA35_PIN(19, PB3, 0x88, 0xc,
+ MA35_MUX(0x0, "GPB3"),
+ MA35_MUX(0x8, "EADC0_CH3")),
+ MA35_PIN(20, PB4, 0x88, 0x10,
+ MA35_MUX(0x0, "GPB4"),
+ MA35_MUX(0x8, "EADC0_CH4")),
+ MA35_PIN(21, PB5, 0x88, 0x14,
+ MA35_MUX(0x0, "GPB5"),
+ MA35_MUX(0x8, "EADC0_CH5")),
+ MA35_PIN(22, PB6, 0x88, 0x18,
+ MA35_MUX(0x0, "GPB6"),
+ MA35_MUX(0x8, "EADC0_CH6")),
+ MA35_PIN(23, PB7, 0x88, 0x1c,
+ MA35_MUX(0x0, "GPB7"),
+ MA35_MUX(0x8, "EADC0_CH7")),
+ MA35_PIN(24, PB8, 0x8c, 0x0,
+ MA35_MUX(0x0, "GPB8"),
+ MA35_MUX(0x1, "EPWM2_BRAKE0"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x6, "SPI0_I2SMCLK"),
+ MA35_MUX(0x8, "ADC0_CH0"),
+ MA35_MUX(0x9, "EBI_nCS0"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xe, "QEI2_INDEX"),
+ MA35_MUX(0xf, "KPI_ROW6")),
+ MA35_PIN(25, PB9, 0x8c, 0x4,
+ MA35_MUX(0x0, "GPB9"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI0_CLK"),
+ MA35_MUX(0x6, "I2S0_MCLK"),
+ MA35_MUX(0x7, "CCAP1_HSYNC"),
+ MA35_MUX(0x8, "ADC0_CH1"),
+ MA35_MUX(0x9, "EBI_ALE"),
+ MA35_MUX(0xa, "EBI_AD13"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "I2S1_MCLK"),
+ MA35_MUX(0xd, "SC0_nCD"),
+ MA35_MUX(0xe, "QEI2_A"),
+ MA35_MUX(0xf, "KPI_ROW7")),
+ MA35_PIN(26, PB10, 0x8c, 0x8,
+ MA35_MUX(0x0, "GPB10"),
+ MA35_MUX(0x1, "EPWM2_CH5"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI0_MOSI"),
+ MA35_MUX(0x6, "EBI_MCLK"),
+ MA35_MUX(0x7, "CCAP1_VSYNC"),
+ MA35_MUX(0x8, "ADC0_CH2"),
+ MA35_MUX(0x9, "EBI_ADR15"),
+ MA35_MUX(0xa, "EBI_AD14"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "I2C1_SDA"),
+ MA35_MUX(0xd, "INT1"),
+ MA35_MUX(0xe, "QEI2_B")),
+ MA35_PIN(27, PB11, 0x8c, 0xc,
+ MA35_MUX(0x0, "GPB11"),
+ MA35_MUX(0x1, "EPWM2_BRAKE1"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI0_MISO"),
+ MA35_MUX(0x6, "I2S1_MCLK"),
+ MA35_MUX(0x7, "CCAP1_SFIELD"),
+ MA35_MUX(0x8, "ADC0_CH3"),
+ MA35_MUX(0x9, "EBI_nCS2"),
+ MA35_MUX(0xa, "EBI_ALE"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "I2C1_SCL"),
+ MA35_MUX(0xd, "INT2"),
+ MA35_MUX(0xe, "QEI2_INDEX")),
+ MA35_PIN(28, PB12, 0x8c, 0x10,
+ MA35_MUX(0x0, "GPB12"),
+ MA35_MUX(0x1, "EPWM2_CH0"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "CAN2_RXD"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x8, "ADC0_CH4"),
+ MA35_MUX(0x9, "EBI_ADR16"),
+ MA35_MUX(0xe, "ECAP2_IC0")),
+ MA35_PIN(29, PB13, 0x8c, 0x14,
+ MA35_MUX(0x0, "GPB13"),
+ MA35_MUX(0x1, "EPWM2_CH1"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x5, "CAN2_TXD"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x8, "ADC0_CH5"),
+ MA35_MUX(0x9, "EBI_ADR17"),
+ MA35_MUX(0xe, "ECAP2_IC1")),
+ MA35_PIN(30, PB14, 0x8c, 0x18,
+ MA35_MUX(0x0, "GPB14"),
+ MA35_MUX(0x1, "EPWM2_CH2"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "I2C4_SDA"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x8, "ADC0_CH6"),
+ MA35_MUX(0x9, "EBI_ADR18"),
+ MA35_MUX(0xe, "ECAP2_IC2")),
+ MA35_PIN(31, PB15, 0x8c, 0x1c,
+ MA35_MUX(0x0, "GPB15"),
+ MA35_MUX(0x1, "EPWM2_CH3"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "I2C4_SCL"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x8, "ADC0_CH7"),
+ MA35_MUX(0x9, "EBI_ADR19")),
+ MA35_PIN(32, PC0, 0x90, 0x0,
+ MA35_MUX(0x0, "GPC0"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "SD0_CMD/eMMC0_CMD")),
+ MA35_PIN(33, PC1, 0x90, 0x4,
+ MA35_MUX(0x0, "GPC1"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "SD0_CLK/eMMC0_CLK")),
+ MA35_PIN(34, PC2, 0x90, 0x8,
+ MA35_MUX(0x0, "GPC2"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "SD0_DAT0/eMMC0_DAT0")),
+ MA35_PIN(35, PC3, 0x90, 0xc,
+ MA35_MUX(0x0, "GPC3"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "SD0_DAT1/eMMC0_DAT1")),
+ MA35_PIN(36, PC4, 0x90, 0x10,
+ MA35_MUX(0x0, "GPC4"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "SD0_DAT2/eMMC0_DAT2")),
+ MA35_PIN(37, PC5, 0x90, 0x14,
+ MA35_MUX(0x0, "GPC5"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "SD0_DAT3/eMMC0_DAT3")),
+ MA35_PIN(38, PC6, 0x90, 0x18,
+ MA35_MUX(0x0, "GPC6"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "SD0_nCD")),
+ MA35_PIN(39, PC7, 0x90, 0x1c,
+ MA35_MUX(0x0, "GPC7"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "SD0_WP")),
+ MA35_PIN(40, PC12, 0x94, 0x10,
+ MA35_MUX(0x0, "GPC12"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART11_RXD"),
+ MA35_MUX(0x6, "LCM_DATA16")),
+ MA35_PIN(41, PC13, 0x94, 0x14,
+ MA35_MUX(0x0, "GPC13"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART11_TXD"),
+ MA35_MUX(0x6, "LCM_DATA17")),
+ MA35_PIN(42, PC14, 0x94, 0x18,
+ MA35_MUX(0x0, "GPC14"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x6, "LCM_DATA18")),
+ MA35_PIN(43, PC15, 0x94, 0x1c,
+ MA35_MUX(0x0, "GPC15"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x6, "LCM_DATA19"),
+ MA35_MUX(0x7, "LCM_MPU_TE"),
+ MA35_MUX(0x8, "LCM_MPU_VSYNC")),
+ MA35_PIN(44, PD0, 0x98, 0x0,
+ MA35_MUX(0x0, "GPD0"),
+ MA35_MUX(0x2, "UART3_nCTS"),
+ MA35_MUX(0x3, "UART4_RXD"),
+ MA35_MUX(0x5, "QSPI0_SS0")),
+ MA35_PIN(45, PD1, 0x98, 0x4,
+ MA35_MUX(0x0, "GPD1"),
+ MA35_MUX(0x2, "UART3_nRTS"),
+ MA35_MUX(0x3, "UART4_TXD"),
+ MA35_MUX(0x5, "QSPI0_CLK")),
+ MA35_PIN(46, PD2, 0x98, 0x8,
+ MA35_MUX(0x0, "GPD2"),
+ MA35_MUX(0x2, "UART3_RXD"),
+ MA35_MUX(0x5, "QSPI0_MOSI0")),
+ MA35_PIN(47, PD3, 0x98, 0xc,
+ MA35_MUX(0x0, "GPD3"),
+ MA35_MUX(0x2, "UART3_TXD"),
+ MA35_MUX(0x5, "QSPI0_MISO0")),
+ MA35_PIN(48, PD4, 0x98, 0x10,
+ MA35_MUX(0x0, "GPD4"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART2_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "QSPI0_MOSI1")),
+ MA35_PIN(49, PD5, 0x98, 0x14,
+ MA35_MUX(0x0, "GPD5"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART2_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "QSPI0_MISO1")),
+ MA35_PIN(50, PD6, 0x98, 0x18,
+ MA35_MUX(0x0, "GPD6"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x5, "QSPI1_MOSI1"),
+ MA35_MUX(0x6, "I2C0_SDA"),
+ MA35_MUX(0x7, "I2S0_MCLK"),
+ MA35_MUX(0x8, "EPWM0_CH0"),
+ MA35_MUX(0x9, "EBI_AD5"),
+ MA35_MUX(0xa, "SPI3_SS1"),
+ MA35_MUX(0xb, "TRACE_CLK")),
+ MA35_PIN(51, PD7, 0x98, 0x1c,
+ MA35_MUX(0x0, "GPD7"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x5, "QSPI1_MISO1"),
+ MA35_MUX(0x6, "I2C0_SCL"),
+ MA35_MUX(0x7, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EPWM0_CH1"),
+ MA35_MUX(0x9, "EBI_AD6"),
+ MA35_MUX(0xa, "SC1_nCD"),
+ MA35_MUX(0xb, "EADC0_ST")),
+ MA35_PIN(52, PD8, 0x9c, 0x0,
+ MA35_MUX(0x0, "GPD8"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART16_nCTS"),
+ MA35_MUX(0x3, "UART15_RXD"),
+ MA35_MUX(0x5, "QSPI1_SS0"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EPWM0_CH2"),
+ MA35_MUX(0x9, "EBI_AD7"),
+ MA35_MUX(0xa, "SC1_CLK"),
+ MA35_MUX(0xb, "TM0")),
+ MA35_PIN(53, PD9, 0x9c, 0x4,
+ MA35_MUX(0x0, "GPD9"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART16_nRTS"),
+ MA35_MUX(0x3, "UART15_TXD"),
+ MA35_MUX(0x5, "QSPI1_CLK"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EPWM0_CH3"),
+ MA35_MUX(0x9, "EBI_AD8"),
+ MA35_MUX(0xa, "SC1_DAT"),
+ MA35_MUX(0xb, "TM0_EXT")),
+ MA35_PIN(54, PD10, 0x9c, 0x8,
+ MA35_MUX(0x0, "GPD10"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART16_RXD"),
+ MA35_MUX(0x5, "QSPI1_MOSI0"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "EPWM0_CH4"),
+ MA35_MUX(0x9, "EBI_AD9"),
+ MA35_MUX(0xa, "SC1_RST"),
+ MA35_MUX(0xb, "TM2")),
+ MA35_PIN(55, PD11, 0x9c, 0xc,
+ MA35_MUX(0x0, "GPD11"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART16_TXD"),
+ MA35_MUX(0x5, "QSPI1_MISO0"),
+ MA35_MUX(0x7, "I2S1_DO"),
+ MA35_MUX(0x8, "EPWM0_CH5"),
+ MA35_MUX(0x9, "EBI_AD10"),
+ MA35_MUX(0xa, "SC1_PWR"),
+ MA35_MUX(0xb, "TM2_EXT")),
+ MA35_PIN(56, PD12, 0x9c, 0x10,
+ MA35_MUX(0x0, "GPD12"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "TRACE_DATA0"),
+ MA35_MUX(0x7, "EBI_nCS1"),
+ MA35_MUX(0x8, "EBI_AD4"),
+ MA35_MUX(0x9, "QEI0_INDEX"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "I2S1_LRCK"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(57, PD13, 0x9c, 0x14,
+ MA35_MUX(0x0, "GPD13"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "TRACE_DATA1"),
+ MA35_MUX(0x7, "EBI_nCS2"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0x9, "ECAP0_IC0"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "I2S1_BCLK")),
+ MA35_PIN(58, PD14, 0x9c, 0x18,
+ MA35_MUX(0x0, "GPD14"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "TRACE_DATA2"),
+ MA35_MUX(0x7, "EBI_MCLK"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0x9, "ECAP0_IC1"),
+ MA35_MUX(0xb, "TM6"),
+ MA35_MUX(0xc, "I2S1_DI"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(59, PD15, 0x9c, 0x1c,
+ MA35_MUX(0x0, "GPD15"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "TRACE_DATA3"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0x9, "ECAP0_IC2"),
+ MA35_MUX(0xb, "TM6_EXT"),
+ MA35_MUX(0xc, "I2S1_DO")),
+ MA35_PIN(60, PE0, 0xa0, 0x0,
+ MA35_MUX(0x0, "GPE0"),
+ MA35_MUX(0x2, "UART9_nCTS"),
+ MA35_MUX(0x3, "UART8_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA0"),
+ MA35_MUX(0x8, "RGMII0_MDC"),
+ MA35_MUX(0x9, "RMII0_MDC")),
+ MA35_PIN(61, PE1, 0xa0, 0x4,
+ MA35_MUX(0x0, "GPE1"),
+ MA35_MUX(0x2, "UART9_nRTS"),
+ MA35_MUX(0x3, "UART8_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA1"),
+ MA35_MUX(0x8, "RGMII0_MDIO"),
+ MA35_MUX(0x9, "RMII0_MDIO")),
+ MA35_PIN(62, PE2, 0xa0, 0x8,
+ MA35_MUX(0x0, "GPE2"),
+ MA35_MUX(0x2, "UART9_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA2"),
+ MA35_MUX(0x8, "RGMII0_TXCTL"),
+ MA35_MUX(0x9, "RMII0_TXEN")),
+ MA35_PIN(63, PE3, 0xa0, 0xc,
+ MA35_MUX(0x0, "GPE3"),
+ MA35_MUX(0x2, "UART9_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA3"),
+ MA35_MUX(0x8, "RGMII0_TXD0"),
+ MA35_MUX(0x9, "RMII0_TXD0")),
+ MA35_PIN(64, PE4, 0xa0, 0x10,
+ MA35_MUX(0x0, "GPE4"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA4"),
+ MA35_MUX(0x8, "RGMII0_TXD1"),
+ MA35_MUX(0x9, "RMII0_TXD1")),
+ MA35_PIN(65, PE5, 0xa0, 0x14,
+ MA35_MUX(0x0, "GPE5"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA5"),
+ MA35_MUX(0x8, "RGMII0_RXCLK"),
+ MA35_MUX(0x9, "RMII0_REFCLK")),
+ MA35_PIN(66, PE6, 0xa0, 0x18,
+ MA35_MUX(0x0, "GPE6"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA6"),
+ MA35_MUX(0x8, "RGMII0_RXCTL"),
+ MA35_MUX(0x9, "RMII0_CRSDV")),
+ MA35_PIN(67, PE7, 0xa0, 0x1c,
+ MA35_MUX(0x0, "GPE7"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA7"),
+ MA35_MUX(0x8, "RGMII0_RXD0"),
+ MA35_MUX(0x9, "RMII0_RXD0")),
+ MA35_PIN(68, PE8, 0xa4, 0x0,
+ MA35_MUX(0x0, "GPE8"),
+ MA35_MUX(0x2, "UART13_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x7, "CCAP1_SCLK"),
+ MA35_MUX(0x8, "RGMII0_RXD1"),
+ MA35_MUX(0x9, "RMII0_RXD1")),
+ MA35_PIN(69, PE9, 0xa4, 0x4,
+ MA35_MUX(0x0, "GPE9"),
+ MA35_MUX(0x2, "UART13_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x7, "CCAP1_PIXCLK"),
+ MA35_MUX(0x8, "RGMII0_RXD2"),
+ MA35_MUX(0x9, "RMII0_RXERR")),
+ MA35_PIN(70, PE10, 0xa4, 0x8,
+ MA35_MUX(0x0, "GPE10"),
+ MA35_MUX(0x2, "UART15_nCTS"),
+ MA35_MUX(0x3, "UART14_RXD"),
+ MA35_MUX(0x5, "SPI1_SS0"),
+ MA35_MUX(0x7, "CCAP1_HSYNC"),
+ MA35_MUX(0x8, "RGMII0_RXD3")),
+ MA35_PIN(71, PE11, 0xa4, 0xc,
+ MA35_MUX(0x0, "GPE11"),
+ MA35_MUX(0x2, "UART15_nRTS"),
+ MA35_MUX(0x3, "UART14_TXD"),
+ MA35_MUX(0x5, "SPI1_CLK"),
+ MA35_MUX(0x7, "CCAP1_VSYNC"),
+ MA35_MUX(0x8, "RGMII0_TXCLK")),
+ MA35_PIN(72, PE12, 0xa4, 0x10,
+ MA35_MUX(0x0, "GPE12"),
+ MA35_MUX(0x2, "UART15_RXD"),
+ MA35_MUX(0x5, "SPI1_MOSI"),
+ MA35_MUX(0x7, "CCAP1_DATA8"),
+ MA35_MUX(0x8, "RGMII0_TXD2")),
+ MA35_PIN(73, PE13, 0xa4, 0x14,
+ MA35_MUX(0x0, "GPE13"),
+ MA35_MUX(0x2, "UART15_TXD"),
+ MA35_MUX(0x5, "SPI1_MISO"),
+ MA35_MUX(0x7, "CCAP1_DATA9"),
+ MA35_MUX(0x8, "RGMII0_TXD3")),
+ MA35_PIN(74, PE14, 0xa4, 0x18,
+ MA35_MUX(0x0, "GPE14"),
+ MA35_MUX(0x1, "UART0_TXD")),
+ MA35_PIN(75, PE15, 0xa4, 0x1c,
+ MA35_MUX(0x0, "GPE15"),
+ MA35_MUX(0x1, "UART0_RXD")),
+ MA35_PIN(76, PF0, 0xa8, 0x0,
+ MA35_MUX(0x0, "GPF0"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x6, "RGMII0_RXD3"),
+ MA35_MUX(0x8, "RGMII1_MDC"),
+ MA35_MUX(0x9, "RMII1_MDC"),
+ MA35_MUX(0xe, "KPI_COL0")),
+ MA35_PIN(77, PF1, 0xa8, 0x4,
+ MA35_MUX(0x0, "GPF1"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x6, "RGMII0_TXCLK"),
+ MA35_MUX(0x8, "RGMII1_MDIO"),
+ MA35_MUX(0x9, "RMII1_MDIO"),
+ MA35_MUX(0xe, "KPI_COL1")),
+ MA35_PIN(78, PF2, 0xa8, 0x8,
+ MA35_MUX(0x0, "GPF2"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x6, "RGMII0_TXD2"),
+ MA35_MUX(0x8, "RGMII1_TXCTL"),
+ MA35_MUX(0x9, "RMII1_TXEN"),
+ MA35_MUX(0xe, "KPI_COL2")),
+ MA35_PIN(79, PF3, 0xa8, 0xc,
+ MA35_MUX(0x0, "GPF3"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x6, "RGMII0_TXD3"),
+ MA35_MUX(0x8, "RGMII1_TXD0"),
+ MA35_MUX(0x9, "RMII1_TXD0"),
+ MA35_MUX(0xe, "KPI_COL3")),
+ MA35_PIN(80, PF4, 0xa8, 0x10,
+ MA35_MUX(0x0, "GPF4"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2S0_LRCK"),
+ MA35_MUX(0x5, "SPI1_SS0"),
+ MA35_MUX(0x8, "RGMII1_TXD1"),
+ MA35_MUX(0x9, "RMII1_TXD1"),
+ MA35_MUX(0xd, "CAN2_RXD"),
+ MA35_MUX(0xe, "KPI_ROW0")),
+ MA35_PIN(81, PF5, 0xa8, 0x14,
+ MA35_MUX(0x0, "GPF5"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2S0_BCLK"),
+ MA35_MUX(0x5, "SPI1_CLK"),
+ MA35_MUX(0x8, "RGMII1_RXCLK"),
+ MA35_MUX(0x9, "RMII1_REFCLK"),
+ MA35_MUX(0xd, "CAN2_TXD"),
+ MA35_MUX(0xe, "KPI_ROW1")),
+ MA35_PIN(82, PF6, 0xa8, 0x18,
+ MA35_MUX(0x0, "GPF6"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x4, "I2S0_DI"),
+ MA35_MUX(0x5, "SPI1_MOSI"),
+ MA35_MUX(0x8, "RGMII1_RXCTL"),
+ MA35_MUX(0x9, "RMII1_CRSDV"),
+ MA35_MUX(0xa, "I2C4_SDA"),
+ MA35_MUX(0xd, "SC0_CLK"),
+ MA35_MUX(0xe, "KPI_ROW2")),
+ MA35_PIN(83, PF7, 0xa8, 0x1c,
+ MA35_MUX(0x0, "GPF7"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x4, "I2S0_DO"),
+ MA35_MUX(0x5, "SPI1_MISO"),
+ MA35_MUX(0x8, "RGMII1_RXD0"),
+ MA35_MUX(0x9, "RMII1_RXD0"),
+ MA35_MUX(0xa, "I2C4_SCL"),
+ MA35_MUX(0xd, "SC0_DAT"),
+ MA35_MUX(0xe, "KPI_ROW3")),
+ MA35_PIN(84, PF8, 0xac, 0x0,
+ MA35_MUX(0x0, "GPF8"),
+ MA35_MUX(0x2, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x8, "RGMII1_RXD1"),
+ MA35_MUX(0x9, "RMII1_RXD1"),
+ MA35_MUX(0xd, "SC0_RST"),
+ MA35_MUX(0xe, "KPI_COL4")),
+ MA35_PIN(85, PF9, 0xac, 0x4,
+ MA35_MUX(0x0, "GPF9"),
+ MA35_MUX(0x2, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x8, "RGMII1_RXD2"),
+ MA35_MUX(0x9, "RMII1_RXERR"),
+ MA35_MUX(0xd, "SC0_PWR"),
+ MA35_MUX(0xe, "KPI_COL5")),
+ MA35_PIN(86, PF10, 0xac, 0x8,
+ MA35_MUX(0x0, "GPF10"),
+ MA35_MUX(0x2, "UART13_nCTS"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x6, "SPI1_SS0"),
+ MA35_MUX(0x8, "RGMII1_RXD3"),
+ MA35_MUX(0x9, "SC0_CLK"),
+ MA35_MUX(0xe, "KPI_COL6")),
+ MA35_PIN(87, PF11, 0xac, 0xc,
+ MA35_MUX(0x0, "GPF11"),
+ MA35_MUX(0x2, "UART13_nRTS"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x6, "SPI1_CLK"),
+ MA35_MUX(0x8, "RGMII1_TXCLK"),
+ MA35_MUX(0x9, "SC0_DAT"),
+ MA35_MUX(0xe, "KPI_COL7")),
+ MA35_PIN(88, PF12, 0xac, 0x10,
+ MA35_MUX(0x0, "GPF12"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "SPI1_MOSI"),
+ MA35_MUX(0x8, "RGMII1_TXD2"),
+ MA35_MUX(0x9, "SC0_RST"),
+ MA35_MUX(0xe, "KPI_ROW4")),
+ MA35_PIN(89, PF13, 0xac, 0x14,
+ MA35_MUX(0x0, "GPF13"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x6, "SPI1_MISO"),
+ MA35_MUX(0x8, "RGMII1_TXD3"),
+ MA35_MUX(0x9, "SC0_PWR"),
+ MA35_MUX(0xe, "KPI_ROW5")),
+ MA35_PIN(90, PF14, 0xac, 0x18,
+ MA35_MUX(0x0, "GPF14"),
+ MA35_MUX(0x1, "EPWM2_BRAKE0"),
+ MA35_MUX(0x2, "EADC0_ST"),
+ MA35_MUX(0x3, "RGMII1_PPS"),
+ MA35_MUX(0x4, "RMII1_PPS"),
+ MA35_MUX(0x5, "SPI0_I2SMCLK"),
+ MA35_MUX(0x6, "SPI1_I2SMCLK"),
+ MA35_MUX(0x7, "CCAP1_SFIELD"),
+ MA35_MUX(0x8, "RGMII0_PPS"),
+ MA35_MUX(0x9, "RMII0_PPS"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "INT0"),
+ MA35_MUX(0xd, "SPI1_SS1"),
+ MA35_MUX(0xe, "QEI2_INDEX"),
+ MA35_MUX(0xf, "I2S0_MCLK")),
+ MA35_PIN(91, PF15, 0xac, 0x1c,
+ MA35_MUX(0x0, "GPF15"),
+ MA35_MUX(0x1, "HSUSB0_VBUSVLD")),
+ MA35_PIN(92, PG0, 0xb0, 0x0,
+ MA35_MUX(0x0, "GPG0"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART7_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x7, "EBI_AD15"),
+ MA35_MUX(0x9, "I2S1_MCLK"),
+ MA35_MUX(0xa, "QEI0_INDEX"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xc, "CLKO"),
+ MA35_MUX(0xd, "INT0"),
+ MA35_MUX(0xf, "EBI_ADR15")),
+ MA35_PIN(93, PG1, 0xb0, 0x4,
+ MA35_MUX(0x0, "GPG1"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART9_nRTS"),
+ MA35_MUX(0x3, "UART6_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "CAN2_TXD"),
+ MA35_MUX(0x7, "EBI_nCS0"),
+ MA35_MUX(0x9, "QEI0_B"),
+ MA35_MUX(0xb, "TM1_EXT"),
+ MA35_MUX(0xe, "RGMII1_PPS"),
+ MA35_MUX(0xf, "RMII1_PPS")),
+ MA35_PIN(94, PG2, 0xb0, 0x8,
+ MA35_MUX(0x0, "GPG2"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART9_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x7, "EBI_ADR16"),
+ MA35_MUX(0x8, "EBI_nCS2"),
+ MA35_MUX(0xa, "QEI0_A"),
+ MA35_MUX(0xb, "TM3"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(95, PG3, 0xb0, 0xc,
+ MA35_MUX(0x0, "GPG3"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART9_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI0_I2SMCLK"),
+ MA35_MUX(0x7, "EBI_ADR17"),
+ MA35_MUX(0x8, "EBI_nCS1"),
+ MA35_MUX(0x9, "EBI_MCLK"),
+ MA35_MUX(0xa, "QEI0_B"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xc, "I2S1_MCLK")),
+ MA35_PIN(96, PG4, 0xb0, 0x10,
+ MA35_MUX(0x0, "GPG4"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART5_nCTS"),
+ MA35_MUX(0x3, "UART6_RXD"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "QEI1_INDEX"),
+ MA35_MUX(0x7, "EBI_ADR18"),
+ MA35_MUX(0x8, "EBI_nCS0"),
+ MA35_MUX(0x9, "I2S1_DO"),
+ MA35_MUX(0xa, "SC1_CLK"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xd, "INT2"),
+ MA35_MUX(0xe, "ECAP1_IC2")),
+ MA35_PIN(97, PG5, 0xb0, 0x14,
+ MA35_MUX(0x0, "GPG5"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART5_nRTS"),
+ MA35_MUX(0x3, "UART6_TXD"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "ECAP0_IC0"),
+ MA35_MUX(0x7, "EBI_ADR19"),
+ MA35_MUX(0x8, "EBI_ALE"),
+ MA35_MUX(0x9, "I2S1_DI"),
+ MA35_MUX(0xa, "SC1_DAT"),
+ MA35_MUX(0xb, "TM4_EXT")),
+ MA35_PIN(98, PG6, 0xb0, 0x18,
+ MA35_MUX(0x0, "GPG6"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART5_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "ECAP0_IC1"),
+ MA35_MUX(0x7, "EBI_nRD"),
+ MA35_MUX(0x9, "I2S1_BCLK"),
+ MA35_MUX(0xa, "SC1_RST"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(99, PG7, 0xb0, 0x1c,
+ MA35_MUX(0x0, "GPG7"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART5_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "ECAP0_IC2"),
+ MA35_MUX(0x7, "EBI_nWR"),
+ MA35_MUX(0x9, "I2S1_LRCK"),
+ MA35_MUX(0xa, "SC1_PWR"),
+ MA35_MUX(0xb, "TM7_EXT")),
+ MA35_PIN(100, PG8, 0xb4, 0x0,
+ MA35_MUX(0x0, "GPG8"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "LCM_VSYNC"),
+ MA35_MUX(0x7, "I2C3_SDA"),
+ MA35_MUX(0xc, "EBI_AD7"),
+ MA35_MUX(0xd, "EBI_nCS0")),
+ MA35_PIN(101, PG9, 0xb4, 0x4,
+ MA35_MUX(0x0, "GPG9"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "LCM_HSYNC"),
+ MA35_MUX(0x7, "I2C3_SCL"),
+ MA35_MUX(0xc, "EBI_AD8"),
+ MA35_MUX(0xd, "EBI_nCS1")),
+ MA35_PIN(102, PG10, 0xb4, 0x8,
+ MA35_MUX(0x0, "GPG10"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "LCM_CLK"),
+ MA35_MUX(0xc, "EBI_AD9"),
+ MA35_MUX(0xd, "EBI_nWRH")),
+ MA35_PIN(103, PG11, 0xb4, 0xc,
+ MA35_MUX(0x0, "GPG11"),
+ MA35_MUX(0x3, "JTAG_TDO"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "NAND_RDY1"),
+ MA35_MUX(0x7, "EBI_nWRH"),
+ MA35_MUX(0x8, "EBI_nCS1"),
+ MA35_MUX(0xa, "EBI_AD0")),
+ MA35_PIN(104, PG12, 0xb4, 0x10,
+ MA35_MUX(0x0, "GPG12"),
+ MA35_MUX(0x3, "JTAG_TCK/SW_CLK"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x7, "EBI_nWRL"),
+ MA35_MUX(0xa, "EBI_AD1")),
+ MA35_PIN(105, PG13, 0xb4, 0x14,
+ MA35_MUX(0x0, "GPG13"),
+ MA35_MUX(0x3, "JTAG_TMS/SW_DIO"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x7, "EBI_MCLK"),
+ MA35_MUX(0xa, "EBI_AD2")),
+ MA35_PIN(106, PG14, 0xb4, 0x18,
+ MA35_MUX(0x0, "GPG14"),
+ MA35_MUX(0x3, "JTAG_TDI"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "NAND_nCS1"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0xa, "EBI_AD3")),
+ MA35_PIN(107, PG15, 0xb4, 0x1c,
+ MA35_MUX(0x0, "GPG15"),
+ MA35_MUX(0x3, "JTAG_nTRST"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x7, "EBI_nCS0"),
+ MA35_MUX(0xa, "EBI_AD4")),
+ MA35_PIN(108, PH0, 0xb8, 0x0,
+ MA35_MUX(0x0, "GPH0"),
+ MA35_MUX(0x2, "UART8_nCTS"),
+ MA35_MUX(0x3, "UART7_RXD"),
+ MA35_MUX(0x6, "LCM_DATA8")),
+ MA35_PIN(109, PH1, 0xb8, 0x4,
+ MA35_MUX(0x0, "GPH1"),
+ MA35_MUX(0x2, "UART8_nRTS"),
+ MA35_MUX(0x3, "UART7_TXD"),
+ MA35_MUX(0x6, "LCM_DATA9")),
+ MA35_PIN(110, PH2, 0xb8, 0x8,
+ MA35_MUX(0x0, "GPH2"),
+ MA35_MUX(0x2, "UART8_RXD"),
+ MA35_MUX(0x6, "LCM_DATA10")),
+ MA35_PIN(111, PH3, 0xb8, 0xc,
+ MA35_MUX(0x0, "GPH3"),
+ MA35_MUX(0x2, "UART8_TXD"),
+ MA35_MUX(0x6, "LCM_DATA11")),
+ MA35_PIN(112, PH4, 0xb8, 0x10,
+ MA35_MUX(0x0, "GPH4"),
+ MA35_MUX(0x2, "UART10_nCTS"),
+ MA35_MUX(0x3, "UART9_RXD"),
+ MA35_MUX(0x6, "LCM_DATA12")),
+ MA35_PIN(113, PH5, 0xb8, 0x14,
+ MA35_MUX(0x0, "GPH5"),
+ MA35_MUX(0x2, "UART10_nRTS"),
+ MA35_MUX(0x3, "UART9_TXD"),
+ MA35_MUX(0x6, "LCM_DATA13")),
+ MA35_PIN(114, PH6, 0xb8, 0x18,
+ MA35_MUX(0x0, "GPH6"),
+ MA35_MUX(0x2, "UART10_RXD"),
+ MA35_MUX(0x6, "LCM_DATA14")),
+ MA35_PIN(115, PH7, 0xb8, 0x1c,
+ MA35_MUX(0x0, "GPH7"),
+ MA35_MUX(0x2, "UART10_TXD"),
+ MA35_MUX(0x6, "LCM_DATA15")),
+ MA35_PIN(116, PH8, 0xbc, 0x0,
+ MA35_MUX(0x0, "GPH8"),
+ MA35_MUX(0x6, "TAMPER0")),
+ MA35_PIN(117, PH9, 0xbc, 0x4,
+ MA35_MUX(0x0, "GPH9"),
+ MA35_MUX(0x4, "CLK_32KOUT"),
+ MA35_MUX(0x6, "TAMPER1")),
+ MA35_PIN(118, PH12, 0xbc, 0x10,
+ MA35_MUX(0x0, "GPH12"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x6, "LCM_DATA20")),
+ MA35_PIN(119, PH13, 0xbc, 0x14,
+ MA35_MUX(0x0, "GPH13"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x6, "LCM_DATA21")),
+ MA35_PIN(120, PH14, 0xbc, 0x18,
+ MA35_MUX(0x0, "GPH14"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x6, "LCM_DATA22")),
+ MA35_PIN(121, PH15, 0xbc, 0x1c,
+ MA35_MUX(0x0, "GPH15"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x6, "LCM_DATA23")),
+ MA35_PIN(122, PI0, 0xc0, 0x0,
+ MA35_MUX(0x0, "GPI0"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART11_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x7, "SC0_nCD"),
+ MA35_MUX(0x8, "EBI_ADR0"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "ECAP1_IC0")),
+ MA35_PIN(123, PI1, 0xc0, 0x4,
+ MA35_MUX(0x0, "GPI1"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART11_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x7, "SC0_CLK"),
+ MA35_MUX(0x8, "EBI_ADR1"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "ECAP1_IC1")),
+ MA35_PIN(124, PI2, 0xc0, 0x8,
+ MA35_MUX(0x0, "GPI2"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x7, "SC0_DAT"),
+ MA35_MUX(0x8, "EBI_ADR2"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xc, "ECAP1_IC2")),
+ MA35_PIN(125, PI3, 0xc0, 0xc,
+ MA35_MUX(0x0, "GPI3"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x7, "SC0_RST"),
+ MA35_MUX(0x8, "EBI_ADR3"),
+ MA35_MUX(0xb, "TM1_EXT")),
+ MA35_PIN(126, PI4, 0xc0, 0x10,
+ MA35_MUX(0x0, "GPI4"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI2_SS1"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EBI_ADR4"),
+ MA35_MUX(0xd, "INT0")),
+ MA35_PIN(127, PI5, 0xc0, 0x14,
+ MA35_MUX(0x0, "GPI5"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EBI_ADR5"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(128, PI6, 0xc0, 0x18,
+ MA35_MUX(0x0, "GPI6"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x8, "EBI_ADR6"),
+ MA35_MUX(0xc, "QEI1_INDEX"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(129, PI7, 0xc0, 0x1c,
+ MA35_MUX(0x0, "GPI7"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x8, "EBI_ADR7"),
+ MA35_MUX(0xc, "ECAP0_IC0"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(130, PI8, 0xc4, 0x0,
+ MA35_MUX(0x0, "GPI8"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x6, "LCM_DATA0"),
+ MA35_MUX(0xc, "EBI_AD11")),
+ MA35_PIN(131, PI9, 0xc4, 0x4,
+ MA35_MUX(0x0, "GPI9"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x6, "LCM_DATA1"),
+ MA35_MUX(0xc, "EBI_AD12")),
+ MA35_PIN(132, PI10, 0xc4, 0x8,
+ MA35_MUX(0x0, "GPI10"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x6, "LCM_DATA2"),
+ MA35_MUX(0xc, "EBI_AD13")),
+ MA35_PIN(133, PI11, 0xC4, 0xc,
+ MA35_MUX(0x0, "GPI11"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x6, "LCM_DATA3"),
+ MA35_MUX(0xc, "EBI_AD14")),
+ MA35_PIN(134, PI12, 0xc4, 0x10,
+ MA35_MUX(0x0, "GPI12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART5_RXD"),
+ MA35_MUX(0x6, "LCM_DATA4")),
+ MA35_PIN(135, PI13, 0xc4, 0x14,
+ MA35_MUX(0x0, "GPI13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART5_TXD"),
+ MA35_MUX(0x6, "LCM_DATA5")),
+ MA35_PIN(136, PI14, 0xc4, 0x18,
+ MA35_MUX(0x0, "GPI14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x6, "LCM_DATA6")),
+ MA35_PIN(137, PI15, 0xc4, 0x1c,
+ MA35_MUX(0x0, "GPI15"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x6, "LCM_DATA7")),
+ MA35_PIN(138, PJ0, 0xc8, 0x0,
+ MA35_MUX(0x0, "GPJ0"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART8_nCTS"),
+ MA35_MUX(0x3, "UART7_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "eMMC1_DAT4"),
+ MA35_MUX(0x7, "I2S0_LRCK"),
+ MA35_MUX(0x8, "SC0_CLK"),
+ MA35_MUX(0x9, "EBI_AD11"),
+ MA35_MUX(0xa, "EBI_ADR16"),
+ MA35_MUX(0xb, "EBI_nCS0"),
+ MA35_MUX(0xc, "EBI_AD7")),
+ MA35_PIN(139, PJ1, 0xc8, 0x4,
+ MA35_MUX(0x0, "GPJ1"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART8_nRTS"),
+ MA35_MUX(0x3, "UART7_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "eMMC1_DAT5"),
+ MA35_MUX(0x7, "I2S0_BCLK"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0x9, "EBI_AD12"),
+ MA35_MUX(0xa, "EBI_ADR17"),
+ MA35_MUX(0xb, "EBI_nCS1"),
+ MA35_MUX(0xc, "EBI_AD8")),
+ MA35_PIN(140, PJ2, 0xc8, 0x8,
+ MA35_MUX(0x0, "GPJ2"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART8_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "eMMC1_DAT6"),
+ MA35_MUX(0x7, "I2S0_DI"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0x9, "EBI_AD13"),
+ MA35_MUX(0xa, "EBI_ADR18"),
+ MA35_MUX(0xb, "EBI_nWRH"),
+ MA35_MUX(0xc, "EBI_AD9")),
+ MA35_PIN(141, PJ3, 0xc8, 0xc,
+ MA35_MUX(0x0, "GPJ3"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART8_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "eMMC1_DAT7"),
+ MA35_MUX(0x7, "I2S0_DO"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0x9, "EBI_AD14"),
+ MA35_MUX(0xa, "EBI_ADR19"),
+ MA35_MUX(0xb, "EBI_nWRL"),
+ MA35_MUX(0xc, "EBI_AD10")),
+ MA35_PIN(142, PJ4, 0xc8, 0x10,
+ MA35_MUX(0x0, "GPJ4"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x6, "SD1_WP")),
+ MA35_PIN(143, PJ5, 0xc8, 0x14,
+ MA35_MUX(0x0, "GPJ5"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "SD1_nCD")),
+ MA35_PIN(144, PJ6, 0xc8, 0x18,
+ MA35_MUX(0x0, "GPJ6"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "SD1_CMD/eMMC1_CMD")),
+ MA35_PIN(145, PJ7, 0xc8, 0x1c,
+ MA35_MUX(0x0, "GPJ7"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "SD1_CLK/eMMC1_CLK")),
+ MA35_PIN(146, PJ8, 0xcc, 0x0,
+ MA35_MUX(0x0, "GPJ8"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "SD1_DAT0/eMMC1_DAT0")),
+ MA35_PIN(147, PJ9, 0xcc, 0x4,
+ MA35_MUX(0x0, "GPJ9"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "SD1_DAT1/eMMC1_DAT1")),
+ MA35_PIN(148, PJ10, 0xcc, 0x8,
+ MA35_MUX(0x0, "GPJ10"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "SD1_DAT2/eMMC1_DAT2")),
+ MA35_PIN(149, PJ11, 0xcc, 0xc,
+ MA35_MUX(0x0, "GPJ11"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "SD1_DAT3/eMMC1_DAT3")),
+ MA35_PIN(150, PJ12, 0xcc, 0x10,
+ MA35_MUX(0x0, "GPJ12"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x7, "SC1_CLK"),
+ MA35_MUX(0x8, "EBI_ADR12"),
+ MA35_MUX(0xb, "TM2"),
+ MA35_MUX(0xc, "QEI0_INDEX")),
+ MA35_PIN(151, PJ13, 0xcc, 0x14,
+ MA35_MUX(0x0, "GPJ13"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x7, "SC1_DAT"),
+ MA35_MUX(0x8, "EBI_ADR13"),
+ MA35_MUX(0xb, "TM2_EXT")),
+ MA35_PIN(152, PJ14, 0xcc, 0x18,
+ MA35_MUX(0x0, "GPJ14"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x7, "SC1_RST"),
+ MA35_MUX(0x8, "EBI_ADR14"),
+ MA35_MUX(0xb, "TM3")),
+ MA35_PIN(153, PJ15, 0xcc, 0x1c,
+ MA35_MUX(0x0, "GPJ15"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x7, "SC1_PWR"),
+ MA35_MUX(0x8, "EBI_ADR15"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(154, PK0, 0xd0, 0x0,
+ MA35_MUX(0x0, "GPK0"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART16_nCTS"),
+ MA35_MUX(0x3, "UART15_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EBI_ADR8"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xc, "ECAP0_IC1")),
+ MA35_PIN(155, PK1, 0xd0, 0x4,
+ MA35_MUX(0x0, "GPK1"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART16_nRTS"),
+ MA35_MUX(0x3, "UART15_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x8, "EBI_ADR9"),
+ MA35_MUX(0xb, "TM7_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC2")),
+ MA35_PIN(156, PK2, 0xd0, 0x8,
+ MA35_MUX(0x0, "GPK2"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART16_RXD"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x5, "SPI3_I2SMCLK"),
+ MA35_MUX(0x7, "SC0_PWR"),
+ MA35_MUX(0x8, "EBI_ADR10"),
+ MA35_MUX(0xc, "QEI0_A")),
+ MA35_PIN(157, PK3, 0xd0, 0xc,
+ MA35_MUX(0x0, "GPK3"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART16_TXD"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x5, "SPI3_SS1"),
+ MA35_MUX(0x7, "SC1_nCD"),
+ MA35_MUX(0x8, "EBI_ADR11"),
+ MA35_MUX(0xc, "QEI0_B")),
+ MA35_PIN(158, PK4, 0xd0, 0x10,
+ MA35_MUX(0x0, "GPK4"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "LCM_DEN"),
+ MA35_MUX(0xc, "EBI_AD10"),
+ MA35_MUX(0xd, "EBI_nWRL")),
+ MA35_PIN(159, PK5, 0xd0, 0x14,
+ MA35_MUX(0x0, "GPK5"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xb, "TM8_EXT"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(160, PK6, 0xd0, 0x18,
+ MA35_MUX(0x0, "GPK6"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0xb, "TM6"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(161, PK7, 0xd0, 0x1c,
+ MA35_MUX(0x0, "GPK7"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0x9, "CLKO"),
+ MA35_MUX(0xb, "TM6_EXT"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(162, PK8, 0xd4, 0x0,
+ MA35_MUX(0x0, "GPK8"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x7, "EADC0_ST"),
+ MA35_MUX(0x8, "EBI_AD15"),
+ MA35_MUX(0x9, "EBI_MCLK"),
+ MA35_MUX(0xa, "EBI_ADR15"),
+ MA35_MUX(0xb, "TM8"),
+ MA35_MUX(0xc, "QEI1_INDEX")),
+ MA35_PIN(163, PK9, 0xd4, 0x4,
+ MA35_MUX(0x0, "GPK9"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "CCAP0_SCLK"),
+ MA35_MUX(0x8, "EBI_AD0"),
+ MA35_MUX(0xa, "EBI_ADR0")),
+ MA35_PIN(164, PK10, 0xd4, 0x8,
+ MA35_MUX(0x0, "GPK10"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "CCAP0_PIXCLK"),
+ MA35_MUX(0x8, "EBI_AD1"),
+ MA35_MUX(0xa, "EBI_ADR1")),
+ MA35_PIN(165, PK11, 0xd4, 0xc,
+ MA35_MUX(0x0, "GPK11"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "CCAP0_HSYNC"),
+ MA35_MUX(0x8, "EBI_AD2"),
+ MA35_MUX(0xa, "EBI_ADR2")),
+ MA35_PIN(166, PK12, 0xd4, 0x10,
+ MA35_MUX(0x0, "GPK12"),
+ MA35_MUX(0x1, "EPWM2_CH0"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x6, "SPI1_SS0"),
+ MA35_MUX(0x8, "SC0_CLK"),
+ MA35_MUX(0xb, "TM10"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(167, PK13, 0xd4, 0x14,
+ MA35_MUX(0x0, "GPK13"),
+ MA35_MUX(0x1, "EPWM2_CH1"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x6, "SPI1_CLK"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0xb, "TM10_EXT")),
+ MA35_PIN(168, PK14, 0xd4, 0x18,
+ MA35_MUX(0x0, "GPK14"),
+ MA35_MUX(0x1, "EPWM2_CH2"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "SPI1_MOSI"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0xa, "I2C5_SDA"),
+ MA35_MUX(0xb, "TM11"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(169, PK15, 0xd4, 0x1c,
+ MA35_MUX(0x0, "GPK15"),
+ MA35_MUX(0x1, "EPWM2_CH3"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x6, "SPI1_MISO"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0xa, "I2C5_SCL"),
+ MA35_MUX(0xb, "TM11_EXT")),
+ MA35_PIN(170, PL0, 0xd8, 0x0,
+ MA35_MUX(0x0, "GPL0"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "QSPI1_MOSI1"),
+ MA35_MUX(0x7, "I2S0_LRCK"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0x9, "SC1_CLK"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "QEI1_A")),
+ MA35_PIN(171, PL1, 0xd8, 0x4,
+ MA35_MUX(0x0, "GPL1"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "QSPI1_MISO1"),
+ MA35_MUX(0x7, "I2S0_BCLK"),
+ MA35_MUX(0x8, "EBI_AD12"),
+ MA35_MUX(0x9, "SC1_DAT"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "QEI1_B")),
+ MA35_PIN(172, PL2, 0xd8, 0x8,
+ MA35_MUX(0x0, "GPL2"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "QSPI1_SS1"),
+ MA35_MUX(0x7, "I2S0_DI"),
+ MA35_MUX(0x8, "EBI_AD13"),
+ MA35_MUX(0x9, "SC1_RST"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xc, "QEI1_INDEX")),
+ MA35_PIN(173, PL3, 0xd8, 0xc,
+ MA35_MUX(0x0, "GPL3"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "QSPI1_CLK"),
+ MA35_MUX(0x7, "I2S0_DO"),
+ MA35_MUX(0x8, "EBI_AD14"),
+ MA35_MUX(0x9, "SC1_PWR"),
+ MA35_MUX(0xb, "TM7_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC0")),
+ MA35_PIN(174, PL4, 0xd8, 0x10,
+ MA35_MUX(0x0, "GPL4"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "QSPI1_MOSI0"),
+ MA35_MUX(0x7, "I2S0_MCLK"),
+ MA35_MUX(0x8, "EBI_nRD"),
+ MA35_MUX(0x9, "SC1_nCD"),
+ MA35_MUX(0xb, "TM9"),
+ MA35_MUX(0xc, "ECAP0_IC1")),
+ MA35_PIN(175, PL5, 0xd8, 0x14,
+ MA35_MUX(0x0, "GPL5"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "QSPI1_MISO0"),
+ MA35_MUX(0x7, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EBI_nWR"),
+ MA35_MUX(0x9, "SC0_nCD"),
+ MA35_MUX(0xb, "TM9_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC2")),
+ MA35_PIN(176, PL6, 0xd8, 0x18,
+ MA35_MUX(0x0, "GPL6"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "QSPI1_MOSI1"),
+ MA35_MUX(0x7, "TRACE_CLK"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0xb, "TM3"),
+ MA35_MUX(0xc, "ECAP1_IC0"),
+ MA35_MUX(0xd, "INT0")),
+ MA35_PIN(177, PL7, 0xd8, 0x1c,
+ MA35_MUX(0x0, "GPL7"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "QSPI1_MISO1"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xc, "ECAP1_IC1"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(178, PL8, 0xdc, 0x0,
+ MA35_MUX(0x0, "GPL8"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "EPWM0_CH4"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0x9, "SC0_CLK"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xc, "ECAP1_IC2"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(179, PL9, 0xdc, 0x4,
+ MA35_MUX(0x0, "GPL9"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "EPWM1_CH4"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0x9, "SC0_DAT"),
+ MA35_MUX(0xb, "TM4_EXT"),
+ MA35_MUX(0xc, "QEI0_A"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(180, PL10, 0xdc, 0x8,
+ MA35_MUX(0x0, "GPL10"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "EPWM0_CH5"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0x9, "SC0_RST"),
+ MA35_MUX(0xb, "EBI_nWRH"),
+ MA35_MUX(0xc, "QEI0_B")),
+ MA35_PIN(181, PL11, 0xdc, 0xc,
+ MA35_MUX(0x0, "GPL11"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "EPWM1_CH5"),
+ MA35_MUX(0x7, "I2S1_DO"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0x9, "SC0_PWR"),
+ MA35_MUX(0xb, "EBI_nWRL"),
+ MA35_MUX(0xc, "QEI0_INDEX")),
+ MA35_PIN(182, PL12, 0xdc, 0x10,
+ MA35_MUX(0x0, "GPL12"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART7_nCTS"),
+ MA35_MUX(0x3, "ECAP1_IC0"),
+ MA35_MUX(0x4, "UART14_RXD"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x7, "SC1_CLK"),
+ MA35_MUX(0x8, "EBI_AD0"),
+ MA35_MUX(0x9, "HSUSBH_PWREN"),
+ MA35_MUX(0xa, "I2C2_SDA"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "EPWM0_CH2"),
+ MA35_MUX(0xd, "EBI_AD11"),
+ MA35_MUX(0xe, "RGMII0_PPS"),
+ MA35_MUX(0xf, "RMII0_PPS")),
+ MA35_PIN(183, PL13, 0xdc, 0x14,
+ MA35_MUX(0x0, "GPL13"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART7_nRTS"),
+ MA35_MUX(0x3, "ECAP1_IC1"),
+ MA35_MUX(0x4, "UART14_TXD"),
+ MA35_MUX(0x5, "SPI0_CLK"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x7, "SC1_DAT"),
+ MA35_MUX(0x8, "EBI_AD1"),
+ MA35_MUX(0x9, "HSUSBH_OVC"),
+ MA35_MUX(0xa, "I2C2_SCL"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "EPWM0_CH3"),
+ MA35_MUX(0xd, "EBI_AD12"),
+ MA35_MUX(0xe, "RGMII1_PPS"),
+ MA35_MUX(0xf, "RMII1_PPS")),
+ MA35_PIN(184, PL14, 0xdc, 0x18,
+ MA35_MUX(0x0, "GPL14"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART7_RXD"),
+ MA35_MUX(0x4, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI0_MOSI"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x7, "SC1_RST"),
+ MA35_MUX(0x8, "EBI_AD2"),
+ MA35_MUX(0xb, "TM2"),
+ MA35_MUX(0xc, "INT0"),
+ MA35_MUX(0xd, "EBI_AD13")),
+ MA35_PIN(185, PL15, 0xdc, 0x1c,
+ MA35_MUX(0x0, "GPL15"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART7_TXD"),
+ MA35_MUX(0x3, "TRACE_CLK"),
+ MA35_MUX(0x4, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI0_MISO"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x7, "SC1_PWR"),
+ MA35_MUX(0x8, "EBI_AD3"),
+ MA35_MUX(0xb, "TM2_EXT"),
+ MA35_MUX(0xc, "INT2"),
+ MA35_MUX(0xd, "EBI_AD14")),
+ MA35_PIN(186, PM0, 0xe0, 0x0,
+ MA35_MUX(0x0, "GPM0"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "CCAP0_VSYNC"),
+ MA35_MUX(0x8, "EBI_AD3"),
+ MA35_MUX(0xa, "EBI_ADR3")),
+ MA35_PIN(187, PM1, 0xe0, 0x4,
+ MA35_MUX(0x0, "GPM1"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI3_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP0_SFIELD"),
+ MA35_MUX(0x8, "EBI_AD4"),
+ MA35_MUX(0xa, "EBI_ADR4")),
+ MA35_PIN(188, PM2, 0xe0, 0x8,
+ MA35_MUX(0x0, "GPM2"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "CCAP0_DATA0"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0xa, "EBI_ADR5")),
+ MA35_PIN(189, PM3, 0xe0, 0xc,
+ MA35_MUX(0x0, "GPM3"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "CCAP0_DATA1"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0xa, "EBI_ADR6")),
+ MA35_PIN(190, PM4, 0xe0, 0x10,
+ MA35_MUX(0x0, "GPM4"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP0_DATA2"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0xa, "EBI_ADR7")),
+ MA35_PIN(191, PM5, 0xe0, 0x14,
+ MA35_MUX(0x0, "GPM5"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP0_DATA3"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0xa, "EBI_ADR8")),
+ MA35_PIN(192, PM6, 0xe0, 0x18,
+ MA35_MUX(0x0, "GPM6"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "CCAP0_DATA4"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0xa, "EBI_ADR9")),
+ MA35_PIN(193, PM7, 0xe0, 0x1c,
+ MA35_MUX(0x0, "GPM7"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "CCAP0_DATA5"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0xa, "EBI_ADR10")),
+ MA35_PIN(194, PM8, 0xe4, 0x0,
+ MA35_MUX(0x0, "GPM8"),
+ MA35_MUX(0x4, "I2C0_SDA"),
+ MA35_MUX(0x6, "CCAP0_DATA6"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0xa, "EBI_ADR11")),
+ MA35_PIN(195, PM9, 0xe4, 0x4,
+ MA35_MUX(0x0, "GPM9"),
+ MA35_MUX(0x4, "I2C0_SCL"),
+ MA35_MUX(0x6, "CCAP0_DATA7"),
+ MA35_MUX(0x8, "EBI_AD12"),
+ MA35_MUX(0xa, "EBI_ADR12")),
+ MA35_PIN(196, PM10, 0xe4, 0x8,
+ MA35_MUX(0x0, "GPM10"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "CCAP0_DATA8"),
+ MA35_MUX(0x7, "SPI2_I2SMCLK"),
+ MA35_MUX(0x8, "EBI_AD13"),
+ MA35_MUX(0xa, "EBI_ADR13")),
+ MA35_PIN(197, PM11, 0xe4, 0xc,
+ MA35_MUX(0x0, "GPM11"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x5, "SPI3_SS1"),
+ MA35_MUX(0x6, "CCAP0_DATA9"),
+ MA35_MUX(0x7, "SPI2_SS1"),
+ MA35_MUX(0x8, "EBI_AD14"),
+ MA35_MUX(0xa, "EBI_ADR14")),
+ MA35_PIN(198, PM12, 0xe4, 0x10,
+ MA35_MUX(0x0, "GPM12"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART10_nCTS"),
+ MA35_MUX(0x3, "TRACE_DATA0"),
+ MA35_MUX(0x4, "UART11_RXD"),
+ MA35_MUX(0x5, "I2C2_SDA"),
+ MA35_MUX(0x7, "SC1_nCD"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0x9, "I2S1_MCLK"),
+ MA35_MUX(0xb, "TM8")),
+ MA35_PIN(199, PM13, 0xe4, 0x14,
+ MA35_MUX(0x0, "GPM13"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART10_nRTS"),
+ MA35_MUX(0x3, "TRACE_DATA1"),
+ MA35_MUX(0x4, "UART11_TXD"),
+ MA35_MUX(0x5, "I2C2_SCL"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0x9, "ECAP1_IC0"),
+ MA35_MUX(0xb, "TM8_EXT")),
+ MA35_PIN(200, PM14, 0xe4, 0x18,
+ MA35_MUX(0x0, "GPM14"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART10_RXD"),
+ MA35_MUX(0x3, "TRACE_DATA2"),
+ MA35_MUX(0x4, "CAN2_RXD"),
+ MA35_MUX(0x6, "I2C3_SDA"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0x9, "ECAP1_IC1"),
+ MA35_MUX(0xb, "TM10"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(201, PM15, 0xe4, 0x1c,
+ MA35_MUX(0x0, "GPM15"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART10_TXD"),
+ MA35_MUX(0x3, "TRACE_DATA3"),
+ MA35_MUX(0x4, "CAN2_TXD"),
+ MA35_MUX(0x6, "I2C3_SCL"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0x9, "ECAP1_IC2"),
+ MA35_MUX(0xb, "TM10_EXT"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(202, PN0, 0xe8, 0x0,
+ MA35_MUX(0x0, "GPN0"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x6, "CCAP1_DATA0")),
+ MA35_PIN(203, PN1, 0xe8, 0x4,
+ MA35_MUX(0x0, "GPN1"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x6, "CCAP1_DATA1")),
+ MA35_PIN(204, PN2, 0xe8, 0x8,
+ MA35_MUX(0x0, "GPN2"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "CCAP1_DATA2")),
+ MA35_PIN(205, PN3, 0xe8, 0xc,
+ MA35_MUX(0x0, "GPN3"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "CCAP1_DATA3")),
+ MA35_PIN(206, PN4, 0xe8, 0x10,
+ MA35_MUX(0x0, "GPN4"),
+ MA35_MUX(0x4, "I2C1_SDA"),
+ MA35_MUX(0x6, "CCAP1_DATA4")),
+ MA35_PIN(207, PN5, 0xe8, 0x14,
+ MA35_MUX(0x0, "GPN5"),
+ MA35_MUX(0x4, "I2C1_SCL"),
+ MA35_MUX(0x6, "CCAP1_DATA5")),
+ MA35_PIN(208, PN6, 0xe8, 0x18,
+ MA35_MUX(0x0, "GPN6"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "CCAP1_DATA6")),
+ MA35_PIN(209, PN7, 0xe8, 0x1c,
+ MA35_MUX(0x0, "GPN7"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "CCAP1_DATA7")),
+ MA35_PIN(210, PN10, 0xec, 0x8,
+ MA35_MUX(0x0, "GPN10"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x6, "CCAP1_SCLK")),
+ MA35_PIN(211, PN11, 0xec, 0xc,
+ MA35_MUX(0x0, "GPN11"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x6, "CCAP1_PIXCLK")),
+ MA35_PIN(212, PN12, 0xec, 0x10,
+ MA35_MUX(0x0, "GPN12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP1_HSYNC")),
+ MA35_PIN(213, PN13, 0xec, 0x14,
+ MA35_MUX(0x0, "GPN13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP1_VSYNC")),
+ MA35_PIN(214, PN14, 0xec, 0x18,
+ MA35_MUX(0x0, "GPN14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI1_SS1"),
+ MA35_MUX(0x6, "CCAP1_SFIELD"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK")),
+ MA35_PIN(215, PN15, 0xec, 0x1c,
+ MA35_MUX(0x0, "GPN15"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "SPI1_SS1"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK"),
+ MA35_MUX(0x8, "SC0_nCD"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xa, "CLKO"),
+ MA35_MUX(0xb, "TM6")),
+ MA35_PIN(216, PN8, 0xec, 0x0,
+ MA35_MUX(0x0, "GPN8"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x4, "I2C0_SDA"),
+ MA35_MUX(0x5, "SPI2_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP1_DATA8")),
+ MA35_PIN(217, PN9, 0xec, 0x4,
+ MA35_MUX(0x0, "GPN9"),
+ MA35_MUX(0x1, "EPWM2_CH5"),
+ MA35_MUX(0x4, "I2C0_SCL"),
+ MA35_MUX(0x5, "SPI1_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP1_DATA9")),
+ MA35_PIN(218, PN10, 0xec, 0x8,
+ MA35_MUX(0x0, "GPN10"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x4, "USBHL2_DM"),
+ MA35_MUX(0x6, "CCAP1_SCLK")),
+ MA35_PIN(219, PN11, 0xec, 0xc,
+ MA35_MUX(0x0, "GPN11"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x4, "USBHL2_DP"),
+ MA35_MUX(0x6, "CCAP1_PIXCLK")),
+ MA35_PIN(220, PN12, 0xec, 0x10,
+ MA35_MUX(0x0, "GPN12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP1_HSYNC")),
+ MA35_PIN(221, PN13, 0xec, 0x14,
+ MA35_MUX(0x0, "GPN13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP1_VSYNC")),
+ MA35_PIN(222, PN14, 0xec, 0x18,
+ MA35_MUX(0x0, "GPN14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x4, "USBHL3_DM"),
+ MA35_MUX(0x5, "SPI1_SS1"),
+ MA35_MUX(0x6, "CCAP1_SFIELD"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK")),
+ MA35_PIN(223, PN15, 0xec, 0x1c,
+ MA35_MUX(0x0, "GPN15"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x4, "USBHL3_DP"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "SPI1_SS1"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK"),
+ MA35_MUX(0x8, "SC0_nCD"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xa, "CLKO"),
+ MA35_MUX(0xb, "TM6")),
+};
+
+static int ma35d1_get_pin_num(int offset, int shift)
+{
+ return (offset - 0x80) * 2 + shift / 4;
+}
+
+static struct ma35_pinctrl_soc_info ma35d1_pinctrl_info = {
+ .pins = ma35d1_pins,
+ .npins = ARRAY_SIZE(ma35d1_pins),
+ .get_pin_num = ma35d1_get_pin_num,
+};
+
+static const struct dev_pm_ops ma35d1_pinctrl_pm_ops = {
+ SET_LATE_SYSTEM_SLEEP_PM_OPS(ma35_pinctrl_suspend, ma35_pinctrl_resume)
+};
+
+static int ma35d1_pinctrl_probe(struct platform_device *pdev)
+{
+ return ma35_pinctrl_probe(pdev, &ma35d1_pinctrl_info);
+}
+
+static const struct of_device_id ma35d1_pinctrl_of_match[] = {
+ { .compatible = "nuvoton,ma35d1-pinctrl", },
+ { },
+};
+
+static struct platform_driver ma35d1_pinctrl_driver = {
+ .probe = ma35d1_pinctrl_probe,
+ .driver = {
+ .name = "ma35d1-pinctrl",
+ .pm = &ma35d1_pinctrl_pm_ops,
+ .of_match_table = ma35d1_pinctrl_of_match,
+ },
+};
+
+static int __init ma35d1_pinctrl_init(void)
+{
+ return platform_driver_register(&ma35d1_pinctrl_driver);
+}
+arch_initcall(ma35d1_pinctrl_init);
+
+MODULE_AUTHOR("schung@nuvoton.com");
+MODULE_DESCRIPTION("Nuvoton MA35D1 pinctrl driver");
+MODULE_LICENSE("GPL");
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
2024-03-13 3:57 ` Jacky Huang
@ 2024-03-13 8:04 ` Dan Carpenter
-1 siblings, 0 replies; 16+ messages in thread
From: Dan Carpenter @ 2024-03-13 8:04 UTC (permalink / raw)
To: Jacky Huang
Cc: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer, linux-arm-kernel, linux-gpio, devicetree,
linux-kernel, ychuang3, schung
On Wed, Mar 13, 2024 at 03:57:19AM +0000, Jacky Huang wrote:
> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
> +{
> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
> + struct ma35_pin_bank *bank = ctrl->pin_banks;
> + int ret;
> + int i;
> +
> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
> + if (!bank->valid) {
> + dev_warn(&pdev->dev, "bank %s is not valid\n",
> + bank->np->name);
> + continue;
> + }
> + bank->irqtype = 0;
> + bank->irqinten = 0;
> + bank->chip.label = bank->name;
> + bank->chip.of_gpio_n_cells = 2;
> + bank->chip.parent = &pdev->dev;
> + bank->chip.request = ma35_gpio_core_to_request;
> + bank->chip.direction_input = ma35_gpio_core_direction_in;
> + bank->chip.direction_output = ma35_gpio_core_direction_out;
> + bank->chip.get = ma35_gpio_core_get;
> + bank->chip.set = ma35_gpio_core_set;
> + bank->chip.base = -1;
> + bank->chip.ngpio = bank->nr_pins;
> + bank->chip.can_sleep = false;
> + spin_lock_init(&bank->lock);
> +
> + if (bank->irq > 0) {
> + struct gpio_irq_chip *girq;
> +
> + girq = &bank->chip.irq;
> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
> + girq->parent_handler = ma35_irq_demux_intgroup;
> + girq->num_parents = 1;
> +
> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
> + GFP_KERNEL);
> + if (!girq->parents)
> + return -ENOMEM;
ret = -ENOMEM;
goto fail;
regards,
dan carpenter
> +
> + girq->parents[0] = bank->irq;
> + girq->default_type = IRQ_TYPE_NONE;
> + girq->handler = handle_level_irq;
> + }
> +
> + ret = gpiochip_add_data(&bank->chip, bank);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
> + bank->chip.label, ret);
> + goto fail;
> + }
> + }
> + return 0;
> +
> +fail:
> + for (--i, --bank; i >= 0; --i, --bank) {
> + if (!bank->valid)
> + continue;
> + gpiochip_remove(&bank->chip);
> + }
> + return ret;
> +}
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
@ 2024-03-13 8:04 ` Dan Carpenter
0 siblings, 0 replies; 16+ messages in thread
From: Dan Carpenter @ 2024-03-13 8:04 UTC (permalink / raw)
To: Jacky Huang
Cc: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer, linux-arm-kernel, linux-gpio, devicetree,
linux-kernel, ychuang3, schung
On Wed, Mar 13, 2024 at 03:57:19AM +0000, Jacky Huang wrote:
> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
> +{
> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
> + struct ma35_pin_bank *bank = ctrl->pin_banks;
> + int ret;
> + int i;
> +
> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
> + if (!bank->valid) {
> + dev_warn(&pdev->dev, "bank %s is not valid\n",
> + bank->np->name);
> + continue;
> + }
> + bank->irqtype = 0;
> + bank->irqinten = 0;
> + bank->chip.label = bank->name;
> + bank->chip.of_gpio_n_cells = 2;
> + bank->chip.parent = &pdev->dev;
> + bank->chip.request = ma35_gpio_core_to_request;
> + bank->chip.direction_input = ma35_gpio_core_direction_in;
> + bank->chip.direction_output = ma35_gpio_core_direction_out;
> + bank->chip.get = ma35_gpio_core_get;
> + bank->chip.set = ma35_gpio_core_set;
> + bank->chip.base = -1;
> + bank->chip.ngpio = bank->nr_pins;
> + bank->chip.can_sleep = false;
> + spin_lock_init(&bank->lock);
> +
> + if (bank->irq > 0) {
> + struct gpio_irq_chip *girq;
> +
> + girq = &bank->chip.irq;
> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
> + girq->parent_handler = ma35_irq_demux_intgroup;
> + girq->num_parents = 1;
> +
> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
> + GFP_KERNEL);
> + if (!girq->parents)
> + return -ENOMEM;
ret = -ENOMEM;
goto fail;
regards,
dan carpenter
> +
> + girq->parents[0] = bank->irq;
> + girq->default_type = IRQ_TYPE_NONE;
> + girq->handler = handle_level_irq;
> + }
> +
> + ret = gpiochip_add_data(&bank->chip, bank);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
> + bank->chip.label, ret);
> + goto fail;
> + }
> + }
> + return 0;
> +
> +fail:
> + for (--i, --bank; i >= 0; --i, --bank) {
> + if (!bank->valid)
> + continue;
> + gpiochip_remove(&bank->chip);
> + }
> + return ret;
> +}
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
2024-03-13 8:04 ` Dan Carpenter
@ 2024-03-13 10:25 ` Jacky Huang
-1 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 10:25 UTC (permalink / raw)
To: Dan Carpenter
Cc: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer, linux-arm-kernel, linux-gpio, devicetree,
linux-kernel, ychuang3, schung
On 2024/3/13 下午 04:04, Dan Carpenter wrote:
> On Wed, Mar 13, 2024 at 03:57:19AM +0000, Jacky Huang wrote:
>> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
>> +{
>> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
>> + struct ma35_pin_bank *bank = ctrl->pin_banks;
>> + int ret;
>> + int i;
>> +
>> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
>> + if (!bank->valid) {
>> + dev_warn(&pdev->dev, "bank %s is not valid\n",
>> + bank->np->name);
>> + continue;
>> + }
>> + bank->irqtype = 0;
>> + bank->irqinten = 0;
>> + bank->chip.label = bank->name;
>> + bank->chip.of_gpio_n_cells = 2;
>> + bank->chip.parent = &pdev->dev;
>> + bank->chip.request = ma35_gpio_core_to_request;
>> + bank->chip.direction_input = ma35_gpio_core_direction_in;
>> + bank->chip.direction_output = ma35_gpio_core_direction_out;
>> + bank->chip.get = ma35_gpio_core_get;
>> + bank->chip.set = ma35_gpio_core_set;
>> + bank->chip.base = -1;
>> + bank->chip.ngpio = bank->nr_pins;
>> + bank->chip.can_sleep = false;
>> + spin_lock_init(&bank->lock);
>> +
>> + if (bank->irq > 0) {
>> + struct gpio_irq_chip *girq;
>> +
>> + girq = &bank->chip.irq;
>> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
>> + girq->parent_handler = ma35_irq_demux_intgroup;
>> + girq->num_parents = 1;
>> +
>> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
>> + GFP_KERNEL);
>> + if (!girq->parents)
>> + return -ENOMEM;
> ret = -ENOMEM;
> goto fail;
>
> regards,
> dan carpenter
Thanks, I will fix it.
>> +
>> + girq->parents[0] = bank->irq;
>> + girq->default_type = IRQ_TYPE_NONE;
>> + girq->handler = handle_level_irq;
>> + }
>> +
>> + ret = gpiochip_add_data(&bank->chip, bank);
>> + if (ret) {
>> + dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
>> + bank->chip.label, ret);
>> + goto fail;
>> + }
>> + }
>> + return 0;
>> +
>> +fail:
>> + for (--i, --bank; i >= 0; --i, --bank) {
>> + if (!bank->valid)
>> + continue;
>> + gpiochip_remove(&bank->chip);
>> + }
>> + return ret;
>> +}
Best Regards,
Jacky Huang
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
@ 2024-03-13 10:25 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-13 10:25 UTC (permalink / raw)
To: Dan Carpenter
Cc: linus.walleij, robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel,
j.neuschaefer, linux-arm-kernel, linux-gpio, devicetree,
linux-kernel, ychuang3, schung
On 2024/3/13 下午 04:04, Dan Carpenter wrote:
> On Wed, Mar 13, 2024 at 03:57:19AM +0000, Jacky Huang wrote:
>> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
>> +{
>> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
>> + struct ma35_pin_bank *bank = ctrl->pin_banks;
>> + int ret;
>> + int i;
>> +
>> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
>> + if (!bank->valid) {
>> + dev_warn(&pdev->dev, "bank %s is not valid\n",
>> + bank->np->name);
>> + continue;
>> + }
>> + bank->irqtype = 0;
>> + bank->irqinten = 0;
>> + bank->chip.label = bank->name;
>> + bank->chip.of_gpio_n_cells = 2;
>> + bank->chip.parent = &pdev->dev;
>> + bank->chip.request = ma35_gpio_core_to_request;
>> + bank->chip.direction_input = ma35_gpio_core_direction_in;
>> + bank->chip.direction_output = ma35_gpio_core_direction_out;
>> + bank->chip.get = ma35_gpio_core_get;
>> + bank->chip.set = ma35_gpio_core_set;
>> + bank->chip.base = -1;
>> + bank->chip.ngpio = bank->nr_pins;
>> + bank->chip.can_sleep = false;
>> + spin_lock_init(&bank->lock);
>> +
>> + if (bank->irq > 0) {
>> + struct gpio_irq_chip *girq;
>> +
>> + girq = &bank->chip.irq;
>> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
>> + girq->parent_handler = ma35_irq_demux_intgroup;
>> + girq->num_parents = 1;
>> +
>> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
>> + GFP_KERNEL);
>> + if (!girq->parents)
>> + return -ENOMEM;
> ret = -ENOMEM;
> goto fail;
>
> regards,
> dan carpenter
Thanks, I will fix it.
>> +
>> + girq->parents[0] = bank->irq;
>> + girq->default_type = IRQ_TYPE_NONE;
>> + girq->handler = handle_level_irq;
>> + }
>> +
>> + ret = gpiochip_add_data(&bank->chip, bank);
>> + if (ret) {
>> + dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
>> + bank->chip.label, ret);
>> + goto fail;
>> + }
>> + }
>> + return 0;
>> +
>> +fail:
>> + for (--i, --bank; i >= 0; --i, --bank) {
>> + if (!bank->valid)
>> + continue;
>> + gpiochip_remove(&bank->chip);
>> + }
>> + return ret;
>> +}
Best Regards,
Jacky Huang
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
2024-03-13 3:57 ` Jacky Huang
@ 2024-03-28 9:10 ` Linus Walleij
-1 siblings, 0 replies; 16+ messages in thread
From: Linus Walleij @ 2024-03-28 9:10 UTC (permalink / raw)
To: Jacky Huang
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel, j.neuschaefer,
linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
Hi Jacky,
overall this looks very good.
On Wed, Mar 13, 2024 at 4:57 AM Jacky Huang <ychuang570808@gmail.com> wrote:
> From: Jacky Huang <ychuang3@nuvoton.com>
>
> Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
> add support for ma35d1 pinctrl.
>
> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
(...)
> +static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
> + unsigned int group)
> +{
> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
> + struct ma35_pin_group *grp = &npctl->groups[group];
> + struct ma35_pin_setting *setting = grp->settings;
> + u32 i, regval;
> +
> + dev_dbg(npctl->dev, "enable function %s group %s\n",
> + npctl->functions[selector].name, npctl->groups[group].name);
> +
> + for (i = 0; i < grp->npins; i++) {
> + regmap_read(npctl->regmap, setting->offset, ®val);
> + regval &= ~GENMASK(setting->shift + 3, setting->shift);
Add a comment explaining why you add +3
> +static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
> + void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
> + unsigned long flags;
> + unsigned int regval;
> +
> + spin_lock_irqsave(&bank->lock, flags);
> +
> + regval = readl(reg_mode);
> + regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
> + regval |= MA35_GP_MODE_INPUT << gpio * 2;
Here the first time you do this magic explain in a comment why you
use *2+1 and *2 overall (I guess two bits per line).
> +static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
> +
> + return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
Here add a comment explaining the *4
I guess one 32-bit register per pin?
> +static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
> + void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
> + unsigned int num = (d->hwirq);
> +
> + if (type == IRQ_TYPE_PROBE) {
> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
> + writel(readl(reg_ien) | BIT(num) | BIT(num + 16), reg_ien);
> + bank->irqtype &= ~BIT(num);
> + bank->irqinten |= BIT(num) | BIT(num + 16);
> + return 0;
> + }
> +
> + if (type & IRQ_TYPE_LEVEL_MASK) {
> + writel(readl(reg_itype) | BIT(num), reg_itype);
> + writel(readl(reg_ien) & ~(BIT(num) | BIT(num + 16)), reg_ien);
> + bank->irqtype |= BIT(num);
> + bank->irqinten &= ~(BIT(num) | BIT(num + 16));
> + if (type == IRQ_TYPE_LEVEL_HIGH) {
> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
> + bank->irqinten |= BIT(num + 16);
> + return 0;
> + }
> +
> + if (type == IRQ_TYPE_LEVEL_LOW) {
> + writel(readl(reg_ien) | BIT(num), reg_ien);
> + bank->irqinten |= BIT(num);
> + return 0;
> + }
> +
> + } else {
> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
> + bank->irqtype &= ~BIT(num);
> +
> + if (type & IRQ_TYPE_EDGE_RISING) {
> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
> + bank->irqinten |= BIT(num + 16);
> +
> + } else {
> + writel(readl(reg_ien) & ~BIT(num + 16), reg_ien);
> + bank->irqinten &= ~BIT(num + 16);
> + }
> +
> + if (type & IRQ_TYPE_EDGE_FALLING) {
> + writel(readl(reg_ien) | BIT(num), reg_ien);
> + bank->irqinten |= BIT(num);
> +
> + } else {
> + writel(readl(reg_ien) & ~BIT(num), reg_ien);
> + bank->irqinten &= ~BIT(num);
> + }
> + }
> + return 0;
> +}
I don't understand why you don't set the irq_handler:
irq_set_handler_locked(d, handle_edge_irq);
irq_set_handler_locked(d, handle_level_irq);
It seems you are not handling IRQ_TYPE_EDGE_BOTH?
What happens if both rising and falling is specified simultaneously?
The if/else nesting is hard to read.
switch (type) {
case IRQ_TYPE_EDGE_BOTH:
(...)
case IRQ_TYPE_EDGE_RISING:
(...)
See drivers/gpio/gpio-ftgpio010.c for an example.
Have you checked that handling edge and level IRQs really work
as expected?
> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
> +{
> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
> + struct ma35_pin_bank *bank = ctrl->pin_banks;
> + int ret;
> + int i;
> +
> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
> + if (!bank->valid) {
> + dev_warn(&pdev->dev, "bank %s is not valid\n",
> + bank->np->name);
> + continue;
> + }
> + bank->irqtype = 0;
> + bank->irqinten = 0;
> + bank->chip.label = bank->name;
> + bank->chip.of_gpio_n_cells = 2;
> + bank->chip.parent = &pdev->dev;
> + bank->chip.request = ma35_gpio_core_to_request;
> + bank->chip.direction_input = ma35_gpio_core_direction_in;
> + bank->chip.direction_output = ma35_gpio_core_direction_out;
> + bank->chip.get = ma35_gpio_core_get;
> + bank->chip.set = ma35_gpio_core_set;
> + bank->chip.base = -1;
> + bank->chip.ngpio = bank->nr_pins;
> + bank->chip.can_sleep = false;
> + spin_lock_init(&bank->lock);
> +
> + if (bank->irq > 0) {
> + struct gpio_irq_chip *girq;
> +
> + girq = &bank->chip.irq;
> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
> + girq->parent_handler = ma35_irq_demux_intgroup;
> + girq->num_parents = 1;
> +
> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
> + GFP_KERNEL);
> + if (!girq->parents)
> + return -ENOMEM;
> +
> + girq->parents[0] = bank->irq;
> + girq->default_type = IRQ_TYPE_NONE;
> + girq->handler = handle_level_irq;
Does this really work for the edge IRQs?
I recommend setting this to handle_bad_irq and assign the right
handler in .set_type().
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
@ 2024-03-28 9:10 ` Linus Walleij
0 siblings, 0 replies; 16+ messages in thread
From: Linus Walleij @ 2024-03-28 9:10 UTC (permalink / raw)
To: Jacky Huang
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel, j.neuschaefer,
linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
Hi Jacky,
overall this looks very good.
On Wed, Mar 13, 2024 at 4:57 AM Jacky Huang <ychuang570808@gmail.com> wrote:
> From: Jacky Huang <ychuang3@nuvoton.com>
>
> Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
> add support for ma35d1 pinctrl.
>
> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
(...)
> +static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
> + unsigned int group)
> +{
> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
> + struct ma35_pin_group *grp = &npctl->groups[group];
> + struct ma35_pin_setting *setting = grp->settings;
> + u32 i, regval;
> +
> + dev_dbg(npctl->dev, "enable function %s group %s\n",
> + npctl->functions[selector].name, npctl->groups[group].name);
> +
> + for (i = 0; i < grp->npins; i++) {
> + regmap_read(npctl->regmap, setting->offset, ®val);
> + regval &= ~GENMASK(setting->shift + 3, setting->shift);
Add a comment explaining why you add +3
> +static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
> + void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
> + unsigned long flags;
> + unsigned int regval;
> +
> + spin_lock_irqsave(&bank->lock, flags);
> +
> + regval = readl(reg_mode);
> + regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
> + regval |= MA35_GP_MODE_INPUT << gpio * 2;
Here the first time you do this magic explain in a comment why you
use *2+1 and *2 overall (I guess two bits per line).
> +static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
> +
> + return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
Here add a comment explaining the *4
I guess one 32-bit register per pin?
> +static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
> + void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
> + unsigned int num = (d->hwirq);
> +
> + if (type == IRQ_TYPE_PROBE) {
> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
> + writel(readl(reg_ien) | BIT(num) | BIT(num + 16), reg_ien);
> + bank->irqtype &= ~BIT(num);
> + bank->irqinten |= BIT(num) | BIT(num + 16);
> + return 0;
> + }
> +
> + if (type & IRQ_TYPE_LEVEL_MASK) {
> + writel(readl(reg_itype) | BIT(num), reg_itype);
> + writel(readl(reg_ien) & ~(BIT(num) | BIT(num + 16)), reg_ien);
> + bank->irqtype |= BIT(num);
> + bank->irqinten &= ~(BIT(num) | BIT(num + 16));
> + if (type == IRQ_TYPE_LEVEL_HIGH) {
> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
> + bank->irqinten |= BIT(num + 16);
> + return 0;
> + }
> +
> + if (type == IRQ_TYPE_LEVEL_LOW) {
> + writel(readl(reg_ien) | BIT(num), reg_ien);
> + bank->irqinten |= BIT(num);
> + return 0;
> + }
> +
> + } else {
> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
> + bank->irqtype &= ~BIT(num);
> +
> + if (type & IRQ_TYPE_EDGE_RISING) {
> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
> + bank->irqinten |= BIT(num + 16);
> +
> + } else {
> + writel(readl(reg_ien) & ~BIT(num + 16), reg_ien);
> + bank->irqinten &= ~BIT(num + 16);
> + }
> +
> + if (type & IRQ_TYPE_EDGE_FALLING) {
> + writel(readl(reg_ien) | BIT(num), reg_ien);
> + bank->irqinten |= BIT(num);
> +
> + } else {
> + writel(readl(reg_ien) & ~BIT(num), reg_ien);
> + bank->irqinten &= ~BIT(num);
> + }
> + }
> + return 0;
> +}
I don't understand why you don't set the irq_handler:
irq_set_handler_locked(d, handle_edge_irq);
irq_set_handler_locked(d, handle_level_irq);
It seems you are not handling IRQ_TYPE_EDGE_BOTH?
What happens if both rising and falling is specified simultaneously?
The if/else nesting is hard to read.
switch (type) {
case IRQ_TYPE_EDGE_BOTH:
(...)
case IRQ_TYPE_EDGE_RISING:
(...)
See drivers/gpio/gpio-ftgpio010.c for an example.
Have you checked that handling edge and level IRQs really work
as expected?
> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
> +{
> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
> + struct ma35_pin_bank *bank = ctrl->pin_banks;
> + int ret;
> + int i;
> +
> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
> + if (!bank->valid) {
> + dev_warn(&pdev->dev, "bank %s is not valid\n",
> + bank->np->name);
> + continue;
> + }
> + bank->irqtype = 0;
> + bank->irqinten = 0;
> + bank->chip.label = bank->name;
> + bank->chip.of_gpio_n_cells = 2;
> + bank->chip.parent = &pdev->dev;
> + bank->chip.request = ma35_gpio_core_to_request;
> + bank->chip.direction_input = ma35_gpio_core_direction_in;
> + bank->chip.direction_output = ma35_gpio_core_direction_out;
> + bank->chip.get = ma35_gpio_core_get;
> + bank->chip.set = ma35_gpio_core_set;
> + bank->chip.base = -1;
> + bank->chip.ngpio = bank->nr_pins;
> + bank->chip.can_sleep = false;
> + spin_lock_init(&bank->lock);
> +
> + if (bank->irq > 0) {
> + struct gpio_irq_chip *girq;
> +
> + girq = &bank->chip.irq;
> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
> + girq->parent_handler = ma35_irq_demux_intgroup;
> + girq->num_parents = 1;
> +
> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
> + GFP_KERNEL);
> + if (!girq->parents)
> + return -ENOMEM;
> +
> + girq->parents[0] = bank->irq;
> + girq->default_type = IRQ_TYPE_NONE;
> + girq->handler = handle_level_irq;
Does this really work for the edge IRQs?
I recommend setting this to handle_bad_irq and assign the right
handler in .set_type().
Yours,
Linus Walleij
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
2024-03-28 9:10 ` Linus Walleij
@ 2024-03-29 8:17 ` Jacky Huang
-1 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-29 8:17 UTC (permalink / raw)
To: Linus Walleij
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel, j.neuschaefer,
linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
Dear Linus,
Thanks for your review.
On 2024/3/28 下午 05:10, Linus Walleij wrote:
> Hi Jacky,
>
> overall this looks very good.
>
> On Wed, Mar 13, 2024 at 4:57 AM Jacky Huang <ychuang570808@gmail.com> wrote:
>
>
>> From: Jacky Huang <ychuang3@nuvoton.com>
>>
>> Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
>> add support for ma35d1 pinctrl.
>>
>> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
> (...)
>> +static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
>> + unsigned int group)
>> +{
>> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
>> + struct ma35_pin_group *grp = &npctl->groups[group];
>> + struct ma35_pin_setting *setting = grp->settings;
>> + u32 i, regval;
>> +
>> + dev_dbg(npctl->dev, "enable function %s group %s\n",
>> + npctl->functions[selector].name, npctl->groups[group].name);
>> +
>> + for (i = 0; i < grp->npins; i++) {
>> + regmap_read(npctl->regmap, setting->offset, ®val);
>> + regval &= ~GENMASK(setting->shift + 3, setting->shift);
> Add a comment explaining why you add +3
The pinmux selection is 4 bits. I will use a constant for the bitmask
width instead.
>
>> +static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
>> + void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
>> + unsigned long flags;
>> + unsigned int regval;
>> +
>> + spin_lock_irqsave(&bank->lock, flags);
>> +
>> + regval = readl(reg_mode);
>> + regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
>> + regval |= MA35_GP_MODE_INPUT << gpio * 2;
> Here the first time you do this magic explain in a comment why you
> use *2+1 and *2 overall (I guess two bits per line).
Yes, it is two bits per pin. I will add a comment to explain this.
>> +static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
>> +
>> + return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
> Here add a comment explaining the *4
> I guess one 32-bit register per pin?
Yes, it maps one 32-bit register to a gpio pin.
I will add a comment to explain this.
>> +static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
>> + void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
>> + void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
>> + unsigned int num = (d->hwirq);
>> +
>> + if (type == IRQ_TYPE_PROBE) {
>> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
>> + writel(readl(reg_ien) | BIT(num) | BIT(num + 16), reg_ien);
>> + bank->irqtype &= ~BIT(num);
>> + bank->irqinten |= BIT(num) | BIT(num + 16);
>> + return 0;
>> + }
>> +
>> + if (type & IRQ_TYPE_LEVEL_MASK) {
>> + writel(readl(reg_itype) | BIT(num), reg_itype);
>> + writel(readl(reg_ien) & ~(BIT(num) | BIT(num + 16)), reg_ien);
>> + bank->irqtype |= BIT(num);
>> + bank->irqinten &= ~(BIT(num) | BIT(num + 16));
>> + if (type == IRQ_TYPE_LEVEL_HIGH) {
>> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
>> + bank->irqinten |= BIT(num + 16);
>> + return 0;
>> + }
>> +
>> + if (type == IRQ_TYPE_LEVEL_LOW) {
>> + writel(readl(reg_ien) | BIT(num), reg_ien);
>> + bank->irqinten |= BIT(num);
>> + return 0;
>> + }
>> +
>> + } else {
>> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
>> + bank->irqtype &= ~BIT(num);
>> +
>> + if (type & IRQ_TYPE_EDGE_RISING) {
>> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
>> + bank->irqinten |= BIT(num + 16);
>> +
>> + } else {
>> + writel(readl(reg_ien) & ~BIT(num + 16), reg_ien);
>> + bank->irqinten &= ~BIT(num + 16);
>> + }
>> +
>> + if (type & IRQ_TYPE_EDGE_FALLING) {
>> + writel(readl(reg_ien) | BIT(num), reg_ien);
>> + bank->irqinten |= BIT(num);
>> +
>> + } else {
>> + writel(readl(reg_ien) & ~BIT(num), reg_ien);
>> + bank->irqinten &= ~BIT(num);
>> + }
>> + }
>> + return 0;
>> +}
> I don't understand why you don't set the irq_handler:
> irq_set_handler_locked(d, handle_edge_irq);
> irq_set_handler_locked(d, handle_level_irq);
I will add the irq_set_handler_locked().
> It seems you are not handling IRQ_TYPE_EDGE_BOTH?
> What happens if both rising and falling is specified simultaneously?
>
> The if/else nesting is hard to read.
> switch (type) {
> case IRQ_TYPE_EDGE_BOTH:
> (...)
> case IRQ_TYPE_EDGE_RISING:
> (...)
>
> See drivers/gpio/gpio-ftgpio010.c for an example.
We'll refer to this driver to modify our code.
> Have you checked that handling edge and level IRQs really work
> as expected?
This driver works with edge or level IRQs in linux-5.10, and some
modifications
have been made for upstream. We'll verify if it also works in linux-6.9.
>> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
>> +{
>> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
>> + struct ma35_pin_bank *bank = ctrl->pin_banks;
>> + int ret;
>> + int i;
>> +
>> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
>> + if (!bank->valid) {
>> + dev_warn(&pdev->dev, "bank %s is not valid\n",
>> + bank->np->name);
>> + continue;
>> + }
>> + bank->irqtype = 0;
>> + bank->irqinten = 0;
>> + bank->chip.label = bank->name;
>> + bank->chip.of_gpio_n_cells = 2;
>> + bank->chip.parent = &pdev->dev;
>> + bank->chip.request = ma35_gpio_core_to_request;
>> + bank->chip.direction_input = ma35_gpio_core_direction_in;
>> + bank->chip.direction_output = ma35_gpio_core_direction_out;
>> + bank->chip.get = ma35_gpio_core_get;
>> + bank->chip.set = ma35_gpio_core_set;
>> + bank->chip.base = -1;
>> + bank->chip.ngpio = bank->nr_pins;
>> + bank->chip.can_sleep = false;
>> + spin_lock_init(&bank->lock);
>> +
>> + if (bank->irq > 0) {
>> + struct gpio_irq_chip *girq;
>> +
>> + girq = &bank->chip.irq;
>> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
>> + girq->parent_handler = ma35_irq_demux_intgroup;
>> + girq->num_parents = 1;
>> +
>> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
>> + GFP_KERNEL);
>> + if (!girq->parents)
>> + return -ENOMEM;
>> +
>> + girq->parents[0] = bank->irq;
>> + girq->default_type = IRQ_TYPE_NONE;
>> + girq->handler = handle_level_irq;
> Does this really work for the edge IRQs?
>
> I recommend setting this to handle_bad_irq and assign the right
> handler in .set_type().
>
> Yours,
> Linus Walleij
OK, I will fix it.
Best Regards,
Jacky Huang
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
@ 2024-03-29 8:17 ` Jacky Huang
0 siblings, 0 replies; 16+ messages in thread
From: Jacky Huang @ 2024-03-29 8:17 UTC (permalink / raw)
To: Linus Walleij
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, p.zabel, j.neuschaefer,
linux-arm-kernel, linux-gpio, devicetree, linux-kernel, ychuang3,
schung
Dear Linus,
Thanks for your review.
On 2024/3/28 下午 05:10, Linus Walleij wrote:
> Hi Jacky,
>
> overall this looks very good.
>
> On Wed, Mar 13, 2024 at 4:57 AM Jacky Huang <ychuang570808@gmail.com> wrote:
>
>
>> From: Jacky Huang <ychuang3@nuvoton.com>
>>
>> Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
>> add support for ma35d1 pinctrl.
>>
>> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
> (...)
>> +static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
>> + unsigned int group)
>> +{
>> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
>> + struct ma35_pin_group *grp = &npctl->groups[group];
>> + struct ma35_pin_setting *setting = grp->settings;
>> + u32 i, regval;
>> +
>> + dev_dbg(npctl->dev, "enable function %s group %s\n",
>> + npctl->functions[selector].name, npctl->groups[group].name);
>> +
>> + for (i = 0; i < grp->npins; i++) {
>> + regmap_read(npctl->regmap, setting->offset, ®val);
>> + regval &= ~GENMASK(setting->shift + 3, setting->shift);
> Add a comment explaining why you add +3
The pinmux selection is 4 bits. I will use a constant for the bitmask
width instead.
>
>> +static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
>> + void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
>> + unsigned long flags;
>> + unsigned int regval;
>> +
>> + spin_lock_irqsave(&bank->lock, flags);
>> +
>> + regval = readl(reg_mode);
>> + regval &= ~GENMASK(gpio * 2 + 1, gpio * 2);
>> + regval |= MA35_GP_MODE_INPUT << gpio * 2;
> Here the first time you do this magic explain in a comment why you
> use *2+1 and *2 overall (I guess two bits per line).
Yes, it is two bits per pin. I will add a comment to explain this.
>> +static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
>> +
>> + return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
> Here add a comment explaining the *4
> I guess one 32-bit register per pin?
Yes, it maps one 32-bit register to a gpio pin.
I will add a comment to explain this.
>> +static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
>> + void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
>> + void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
>> + unsigned int num = (d->hwirq);
>> +
>> + if (type == IRQ_TYPE_PROBE) {
>> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
>> + writel(readl(reg_ien) | BIT(num) | BIT(num + 16), reg_ien);
>> + bank->irqtype &= ~BIT(num);
>> + bank->irqinten |= BIT(num) | BIT(num + 16);
>> + return 0;
>> + }
>> +
>> + if (type & IRQ_TYPE_LEVEL_MASK) {
>> + writel(readl(reg_itype) | BIT(num), reg_itype);
>> + writel(readl(reg_ien) & ~(BIT(num) | BIT(num + 16)), reg_ien);
>> + bank->irqtype |= BIT(num);
>> + bank->irqinten &= ~(BIT(num) | BIT(num + 16));
>> + if (type == IRQ_TYPE_LEVEL_HIGH) {
>> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
>> + bank->irqinten |= BIT(num + 16);
>> + return 0;
>> + }
>> +
>> + if (type == IRQ_TYPE_LEVEL_LOW) {
>> + writel(readl(reg_ien) | BIT(num), reg_ien);
>> + bank->irqinten |= BIT(num);
>> + return 0;
>> + }
>> +
>> + } else {
>> + writel(readl(reg_itype) & ~BIT(num), reg_itype);
>> + bank->irqtype &= ~BIT(num);
>> +
>> + if (type & IRQ_TYPE_EDGE_RISING) {
>> + writel(readl(reg_ien) | BIT(num + 16), reg_ien);
>> + bank->irqinten |= BIT(num + 16);
>> +
>> + } else {
>> + writel(readl(reg_ien) & ~BIT(num + 16), reg_ien);
>> + bank->irqinten &= ~BIT(num + 16);
>> + }
>> +
>> + if (type & IRQ_TYPE_EDGE_FALLING) {
>> + writel(readl(reg_ien) | BIT(num), reg_ien);
>> + bank->irqinten |= BIT(num);
>> +
>> + } else {
>> + writel(readl(reg_ien) & ~BIT(num), reg_ien);
>> + bank->irqinten &= ~BIT(num);
>> + }
>> + }
>> + return 0;
>> +}
> I don't understand why you don't set the irq_handler:
> irq_set_handler_locked(d, handle_edge_irq);
> irq_set_handler_locked(d, handle_level_irq);
I will add the irq_set_handler_locked().
> It seems you are not handling IRQ_TYPE_EDGE_BOTH?
> What happens if both rising and falling is specified simultaneously?
>
> The if/else nesting is hard to read.
> switch (type) {
> case IRQ_TYPE_EDGE_BOTH:
> (...)
> case IRQ_TYPE_EDGE_RISING:
> (...)
>
> See drivers/gpio/gpio-ftgpio010.c for an example.
We'll refer to this driver to modify our code.
> Have you checked that handling edge and level IRQs really work
> as expected?
This driver works with edge or level IRQs in linux-5.10, and some
modifications
have been made for upstream. We'll verify if it also works in linux-6.9.
>> +static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
>> +{
>> + struct ma35_pin_ctrl *ctrl = npctl->ctrl;
>> + struct ma35_pin_bank *bank = ctrl->pin_banks;
>> + int ret;
>> + int i;
>> +
>> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
>> + if (!bank->valid) {
>> + dev_warn(&pdev->dev, "bank %s is not valid\n",
>> + bank->np->name);
>> + continue;
>> + }
>> + bank->irqtype = 0;
>> + bank->irqinten = 0;
>> + bank->chip.label = bank->name;
>> + bank->chip.of_gpio_n_cells = 2;
>> + bank->chip.parent = &pdev->dev;
>> + bank->chip.request = ma35_gpio_core_to_request;
>> + bank->chip.direction_input = ma35_gpio_core_direction_in;
>> + bank->chip.direction_output = ma35_gpio_core_direction_out;
>> + bank->chip.get = ma35_gpio_core_get;
>> + bank->chip.set = ma35_gpio_core_set;
>> + bank->chip.base = -1;
>> + bank->chip.ngpio = bank->nr_pins;
>> + bank->chip.can_sleep = false;
>> + spin_lock_init(&bank->lock);
>> +
>> + if (bank->irq > 0) {
>> + struct gpio_irq_chip *girq;
>> +
>> + girq = &bank->chip.irq;
>> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
>> + girq->parent_handler = ma35_irq_demux_intgroup;
>> + girq->num_parents = 1;
>> +
>> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
>> + GFP_KERNEL);
>> + if (!girq->parents)
>> + return -ENOMEM;
>> +
>> + girq->parents[0] = bank->irq;
>> + girq->default_type = IRQ_TYPE_NONE;
>> + girq->handler = handle_level_irq;
> Does this really work for the edge IRQs?
>
> I recommend setting this to handle_bad_irq and assign the right
> handler in .set_type().
>
> Yours,
> Linus Walleij
OK, I will fix it.
Best Regards,
Jacky Huang
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2024-03-29 8:18 UTC | newest]
Thread overview: 16+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-03-13 3:57 [PATCH v6 0/3] Add support for nuvoton ma35d1 pin control Jacky Huang
2024-03-13 3:57 ` Jacky Huang
2024-03-13 3:57 ` [PATCH v6 1/3] dt-bindings: reset: Add syscon to nuvoton ma35d1 system-management node Jacky Huang
2024-03-13 3:57 ` Jacky Huang
2024-03-13 3:57 ` [PATCH v6 2/3] dt-bindings: pinctrl: Document nuvoton ma35d1 pin control Jacky Huang
2024-03-13 3:57 ` Jacky Huang
2024-03-13 3:57 ` [PATCH v6 3/3] pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver Jacky Huang
2024-03-13 3:57 ` Jacky Huang
2024-03-13 8:04 ` Dan Carpenter
2024-03-13 8:04 ` Dan Carpenter
2024-03-13 10:25 ` Jacky Huang
2024-03-13 10:25 ` Jacky Huang
2024-03-28 9:10 ` Linus Walleij
2024-03-28 9:10 ` Linus Walleij
2024-03-29 8:17 ` Jacky Huang
2024-03-29 8:17 ` Jacky Huang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.