* [PATCH V13 0/4] Add PWM support for IPQ chipsets
@ 2023-10-04 9:04 Devi Priya
2023-10-04 9:04 ` [PATCH V13 1/4] pwm: driver for qualcomm ipq6018 pwm block Devi Priya
` (3 more replies)
0 siblings, 4 replies; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:04 UTC (permalink / raw
To: agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
Add PWM driver and binding support for IPQ chipsets.
Also, add support for pwm node in ipq6018.
Devi Priya (4):
pwm: driver for qualcomm ipq6018 pwm block
dt-bindings: pwm: add IPQ6018 binding
dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018
arm64: dts: ipq6018: add pwm node
.../devicetree/bindings/mfd/qcom,tcsr.yaml | 100 +++++--
.../bindings/pwm/qcom,ipq6018-pwm.yaml | 45 +++
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 +-
drivers/pwm/Kconfig | 12 +
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-ipq.c | 282 ++++++++++++++++++
6 files changed, 423 insertions(+), 32 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pwm/qcom,ipq6018-pwm.yaml
create mode 100644 drivers/pwm/pwm-ipq.c
--
2.34.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V13 1/4] pwm: driver for qualcomm ipq6018 pwm block
2023-10-04 9:04 [PATCH V13 0/4] Add PWM support for IPQ chipsets Devi Priya
@ 2023-10-04 9:04 ` Devi Priya
2023-10-04 9:04 ` [PATCH V13 2/4] dt-bindings: pwm: add IPQ6018 binding Devi Priya
` (2 subsequent siblings)
3 siblings, 0 replies; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:04 UTC (permalink / raw
To: agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
Driver for the PWM block in Qualcomm IPQ6018 line of SoCs. Based on
driver from downstream Codeaurora kernel tree. Removed support for older
(V1) variants because I have no access to that hardware.
Tested on IPQ6010 based hardware.
Co-developed-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
V13:
No change
V12:
Fix the below clang warning for overflow check reported by kernel test robot
drivers/pwm/pwm-ipq.c:122:11: warning: result of comparison of constant 16000000000
with expression of type 'unsigned long' is always false [-Wtautological-constant-out-of-range-compare]
>> if (rate > 16ULL * GIGA)
v11:
Address comment from Uwe Kleine-König:
Drop redundant registers field comments
Fix period limit check in .apply
Clarify the comment explaining skip of pre_div > pwm_div values
Add explicit check for clock rate within limit
Add comment explaining the selection of initial pre_div
Use pwm_div division with remainder instead of separate diff calculation
Round up duty_cycle calculation in .get_state
v10:
Restore round up in pwm_div calculation; otherwise diff is always <=
0, so only bingo match works
Don't overwrite min_diff on every loop iteration
v9:
Address comment from Uwe Kleine-König:
Use period_ns*rate in dividers calculation for better accuracy
Round down pre_div and pwm_div
Add a comment explaining why pwm_div can't underflow
Add a comment explaining why pre_div > pwm_div end the search loop
Drop 'CFG_' from register macros
Rename to_ipq_pwm_chip() to ipq_pwm_from_chip()
Change bare 'unsigned' to 'unsigned int'
Clarify the comment on separate REG1 write for enable/disable
Round up the period value in .get_state
Use direct readl/writel so no need to check for regmap errors
v7:
Change 'offset' to 'reg' for the tcsr offset (Rob)
Drop clock name; there is only one clock (Bjorn)
Simplify probe failure code path (Bjorn)
v6:
Address Uwe Kleine-König review comments:
Drop IPQ_PWM_MAX_DEVICES
Rely on assigned-clock-rates; drop IPQ_PWM_CLK_SRC_FREQ
Simplify register offset calculation
Calculate duty cycle more precisely
Refuse to set inverted polarity
Drop redundant IPQ_PWM_REG1_ENABLE bit clear
Remove x1000 factor in pwm_div calculation, use rate directly, and round up
Choose initial pre_div such that pwm_div < IPQ_PWM_MAX_DIV
Ensure pre_div <= pwm_div
Rename close_ to best_
Explain in comment why effective_div doesn't overflow
Limit pwm_div to IPQ_PWM_MAX_DIV - 1 to allow 100% duty cycle
Disable clock only after pwmchip_remove()
const pwm_ops
Other changes:
Add missing linux/bitfield.h header include (kernel test robot)
Adjust code for PWM device node under TCSR (Rob Herring)
v5:
Use &tcsr_q6 syscon to access registers (Bjorn Andersson)
Address Uwe Kleine-König review comments:
Implement .get_state()
Add IPQ_PWM_ prefix to local macros
Use GENMASK/BIT/FIELD_PREP for register fields access
Make type of config_div_and_duty() parameters consistent
Derive IPQ_PWM_MIN_PERIOD_NS from IPQ_PWM_CLK_SRC_FREQ
Integrate enable/disable into config_div_and_duty() to save register read,
and reduce frequency glitch on update
Use min() instead of min_t()
Fix comment format
Use dev_err_probe() to indicate probe step failure
Add missing clk_disable_unprepare() in .remove
Don't set .owner
v4:
Use div64_u64() to fix link for 32-bit targets ((kernel test robot
<lkp@intel.com>, Uwe Kleine-König)
v3:
s/qcom,pwm-ipq6018/qcom,ipq6018-pwm/ (Rob Herring)
Fix integer overflow on 32-bit targets (kernel test robot <lkp@intel.com>)
v2:
Address Uwe Kleine-König review comments:
Fix period calculation when out of range
Don't set period larger than requested
Remove PWM disable on configuration change
Implement .apply instead of non-atomic .config/.enable/.disable
Don't modify PWM on .request/.free
Check pwm_div underflow
Fix various code and comment formatting issues
Other changes:
Use u64 divisor safe division
Remove now empty .request/.free
drivers/pwm/Kconfig | 12 ++
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-ipq.c | 282 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 295 insertions(+)
create mode 100644 drivers/pwm/pwm-ipq.c
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 8ebcddf91f7b..c2d51680823a 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -282,6 +282,18 @@ config PWM_INTEL_LGM
To compile this driver as a module, choose M here: the module
will be called pwm-intel-lgm.
+config PWM_IPQ
+ tristate "IPQ PWM support"
+ depends on ARCH_QCOM || COMPILE_TEST
+ depends on HAVE_CLK && HAS_IOMEM
+ help
+ Generic PWM framework driver for IPQ PWM block which supports
+ 4 pwm channels. Each of the these channels can be configured
+ independent of each other.
+
+ To compile this driver as a module, choose M here: the module
+ will be called pwm-ipq.
+
config PWM_IQS620A
tristate "Azoteq IQS620A PWM support"
depends on MFD_IQS62X || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index c822389c2a24..1b69e8cb2b91 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_PWM_IMX1) += pwm-imx1.o
obj-$(CONFIG_PWM_IMX27) += pwm-imx27.o
obj-$(CONFIG_PWM_IMX_TPM) += pwm-imx-tpm.o
obj-$(CONFIG_PWM_INTEL_LGM) += pwm-intel-lgm.o
+obj-$(CONFIG_PWM_IPQ) += pwm-ipq.o
obj-$(CONFIG_PWM_IQS620A) += pwm-iqs620a.o
obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o
obj-$(CONFIG_PWM_KEEMBAY) += pwm-keembay.o
diff --git a/drivers/pwm/pwm-ipq.c b/drivers/pwm/pwm-ipq.c
new file mode 100644
index 000000000000..5dbe46bb56d6
--- /dev/null
+++ b/drivers/pwm/pwm-ipq.c
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0
+/*
+ * Copyright (c) 2016-2017, 2020 The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/math64.h>
+#include <linux/of_device.h>
+#include <linux/bitfield.h>
+#include <linux/units.h>
+
+/* The frequency range supported is 1 Hz to clock rate */
+#define IPQ_PWM_MAX_PERIOD_NS ((u64)NSEC_PER_SEC)
+
+/*
+ * The max value specified for each field is based on the number of bits
+ * in the pwm control register for that field
+ */
+#define IPQ_PWM_MAX_DIV 0xFFFF
+
+/*
+ * Two 32-bit registers for each PWM: REG0, and REG1.
+ * Base offset for PWM #i is at 8 * #i.
+ */
+#define IPQ_PWM_REG0 0
+#define IPQ_PWM_REG0_PWM_DIV GENMASK(15, 0)
+#define IPQ_PWM_REG0_HI_DURATION GENMASK(31, 16)
+
+#define IPQ_PWM_REG1 4
+#define IPQ_PWM_REG1_PRE_DIV GENMASK(15, 0)
+/*
+ * Enable bit is set to enable output toggling in pwm device.
+ * Update bit is set to reflect the changed divider and high duration
+ * values in register.
+ */
+#define IPQ_PWM_REG1_UPDATE BIT(30)
+#define IPQ_PWM_REG1_ENABLE BIT(31)
+
+struct ipq_pwm_chip {
+ struct pwm_chip chip;
+ struct clk *clk;
+ void __iomem *mem;
+};
+
+static struct ipq_pwm_chip *ipq_pwm_from_chip(struct pwm_chip *chip)
+{
+ return container_of(chip, struct ipq_pwm_chip, chip);
+}
+
+static unsigned int ipq_pwm_reg_read(struct pwm_device *pwm, unsigned int reg)
+{
+ struct ipq_pwm_chip *ipq_chip = ipq_pwm_from_chip(pwm->chip);
+ unsigned int off = 8 * pwm->hwpwm + reg;
+
+ return readl(ipq_chip->mem + off);
+}
+
+static void ipq_pwm_reg_write(struct pwm_device *pwm, unsigned int reg,
+ unsigned int val)
+{
+ struct ipq_pwm_chip *ipq_chip = ipq_pwm_from_chip(pwm->chip);
+ unsigned int off = 8 * pwm->hwpwm + reg;
+
+ writel(val, ipq_chip->mem + off);
+}
+
+static void config_div_and_duty(struct pwm_device *pwm, unsigned int pre_div,
+ unsigned int pwm_div, unsigned long rate, u64 duty_ns,
+ bool enable)
+{
+ unsigned long hi_dur;
+ unsigned long val = 0;
+
+ /*
+ * high duration = pwm duty * (pwm div + 1)
+ * pwm duty = duty_ns / period_ns
+ */
+ hi_dur = div64_u64(duty_ns * rate, (pre_div + 1) * NSEC_PER_SEC);
+
+ val = FIELD_PREP(IPQ_PWM_REG0_HI_DURATION, hi_dur) |
+ FIELD_PREP(IPQ_PWM_REG0_PWM_DIV, pwm_div);
+ ipq_pwm_reg_write(pwm, IPQ_PWM_REG0, val);
+
+ val = FIELD_PREP(IPQ_PWM_REG1_PRE_DIV, pre_div);
+ ipq_pwm_reg_write(pwm, IPQ_PWM_REG1, val);
+
+ /* PWM enable toggle needs a separate write to REG1 */
+ val |= IPQ_PWM_REG1_UPDATE;
+ if (enable)
+ val |= IPQ_PWM_REG1_ENABLE;
+ ipq_pwm_reg_write(pwm, IPQ_PWM_REG1, val);
+}
+
+static int ipq_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct ipq_pwm_chip *ipq_chip = ipq_pwm_from_chip(chip);
+ unsigned int pre_div, pwm_div, best_pre_div, best_pwm_div;
+ unsigned long rate = clk_get_rate(ipq_chip->clk);
+ u64 period_ns, duty_ns, period_rate;
+ u64 min_diff;
+
+ if (state->polarity != PWM_POLARITY_NORMAL)
+ return -EINVAL;
+
+ if (state->period < DIV64_U64_ROUND_UP(NSEC_PER_SEC, rate))
+ return -ERANGE;
+
+ period_ns = min(state->period, IPQ_PWM_MAX_PERIOD_NS);
+ duty_ns = min(state->duty_cycle, period_ns);
+
+ /*
+ * period_ns is 1G or less. As long as rate is less than 16 GHz,
+ * period_rate does not overflow. Make that explicit.
+ */
+ if ((unsigned long long)rate > 16ULL * GIGA)
+ return -EINVAL;
+ period_rate = period_ns * rate;
+ best_pre_div = IPQ_PWM_MAX_DIV;
+ best_pwm_div = IPQ_PWM_MAX_DIV;
+ /*
+ * We don't need to consider pre_div values smaller than
+ *
+ * period_rate
+ * pre_div_min := ------------------------------------
+ * NSEC_PER_SEC * (IPQ_PWM_MAX_DIV + 1)
+ *
+ * because pre_div = pre_div_min results in a better
+ * approximation.
+ */
+ pre_div = div64_u64(period_rate,
+ (u64)NSEC_PER_SEC * (IPQ_PWM_MAX_DIV + 1));
+ min_diff = period_rate;
+
+ for (; pre_div <= IPQ_PWM_MAX_DIV; pre_div++) {
+ u64 remainder;
+
+ pwm_div = div64_u64_rem(period_rate,
+ (u64)NSEC_PER_SEC * (pre_div + 1), &remainder);
+ /* pwm_div is unsigned; the check below catches underflow */
+ pwm_div--;
+
+ /*
+ * Swapping values for pre_div and pwm_div produces the same
+ * period length. So we can skip all settings with pre_div >
+ * pwm_div which results in bigger constraints for selecting
+ * the duty_cycle than with the two values swapped.
+ */
+ if (pre_div > pwm_div)
+ break;
+
+ /*
+ * Make sure we can do 100% duty cycle where
+ * hi_dur == pwm_div + 1
+ */
+ if (pwm_div > IPQ_PWM_MAX_DIV - 1)
+ continue;
+
+ if (remainder < min_diff) {
+ best_pre_div = pre_div;
+ best_pwm_div = pwm_div;
+ min_diff = remainder;
+
+ if (min_diff == 0) /* bingo */
+ break;
+ }
+ }
+
+ /* config divider values for the closest possible frequency */
+ config_div_and_duty(pwm, best_pre_div, best_pwm_div,
+ rate, duty_ns, state->enabled);
+
+ return 0;
+}
+
+static int ipq_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct ipq_pwm_chip *ipq_chip = ipq_pwm_from_chip(chip);
+ unsigned long rate = clk_get_rate(ipq_chip->clk);
+ unsigned int pre_div, pwm_div, hi_dur;
+ u64 effective_div, hi_div;
+ u32 reg0, reg1;
+
+ reg0 = ipq_pwm_reg_read(pwm, IPQ_PWM_REG0);
+ reg1 = ipq_pwm_reg_read(pwm, IPQ_PWM_REG1);
+
+ state->polarity = PWM_POLARITY_NORMAL;
+ state->enabled = reg1 & IPQ_PWM_REG1_ENABLE;
+
+ pwm_div = FIELD_GET(IPQ_PWM_REG0_PWM_DIV, reg0);
+ hi_dur = FIELD_GET(IPQ_PWM_REG0_HI_DURATION, reg0);
+ pre_div = FIELD_GET(IPQ_PWM_REG1_PRE_DIV, reg1);
+
+ /* No overflow here, both pre_div and pwm_div <= 0xffff */
+ effective_div = (u64)(pre_div + 1) * (pwm_div + 1);
+ state->period = DIV64_U64_ROUND_UP(effective_div * NSEC_PER_SEC, rate);
+
+ hi_div = hi_dur * (pre_div + 1);
+ state->duty_cycle = DIV64_U64_ROUND_UP(hi_div * NSEC_PER_SEC, rate);
+
+ return 0;
+}
+
+static const struct pwm_ops ipq_pwm_ops = {
+ .apply = ipq_pwm_apply,
+ .get_state = ipq_pwm_get_state,
+ .owner = THIS_MODULE,
+};
+
+static int ipq_pwm_probe(struct platform_device *pdev)
+{
+ struct ipq_pwm_chip *pwm;
+ struct device *dev = &pdev->dev;
+ int ret;
+
+ pwm = devm_kzalloc(dev, sizeof(*pwm), GFP_KERNEL);
+ if (!pwm)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, pwm);
+
+ pwm->mem = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(pwm->mem))
+ return dev_err_probe(dev, PTR_ERR(pwm->mem),
+ "regs map failed");
+
+ pwm->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(pwm->clk))
+ return dev_err_probe(dev, PTR_ERR(pwm->clk),
+ "failed to get clock");
+
+ ret = clk_prepare_enable(pwm->clk);
+ if (ret)
+ return dev_err_probe(dev, ret, "clock enable failed");
+
+ pwm->chip.dev = dev;
+ pwm->chip.ops = &ipq_pwm_ops;
+ pwm->chip.npwm = 4;
+
+ ret = pwmchip_add(&pwm->chip);
+ if (ret < 0) {
+ dev_err_probe(dev, ret, "pwmchip_add() failed\n");
+ clk_disable_unprepare(pwm->clk);
+ }
+
+ return ret;
+}
+
+static int ipq_pwm_remove(struct platform_device *pdev)
+{
+ struct ipq_pwm_chip *pwm = platform_get_drvdata(pdev);
+
+ pwmchip_remove(&pwm->chip);
+ clk_disable_unprepare(pwm->clk);
+
+ return 0;
+}
+
+static const struct of_device_id pwm_ipq_dt_match[] = {
+ { .compatible = "qcom,ipq6018-pwm", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, pwm_ipq_dt_match);
+
+static struct platform_driver ipq_pwm_driver = {
+ .driver = {
+ .name = "ipq-pwm",
+ .of_match_table = pwm_ipq_dt_match,
+ },
+ .probe = ipq_pwm_probe,
+ .remove = ipq_pwm_remove,
+};
+
+module_platform_driver(ipq_pwm_driver);
+
+MODULE_LICENSE("Dual BSD/GPL");
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V13 2/4] dt-bindings: pwm: add IPQ6018 binding
2023-10-04 9:04 [PATCH V13 0/4] Add PWM support for IPQ chipsets Devi Priya
2023-10-04 9:04 ` [PATCH V13 1/4] pwm: driver for qualcomm ipq6018 pwm block Devi Priya
@ 2023-10-04 9:04 ` Devi Priya
2023-10-04 9:13 ` Krzysztof Kozlowski
2023-10-04 9:04 ` [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018 Devi Priya
2023-10-04 9:04 ` [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node Devi Priya
3 siblings, 1 reply; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:04 UTC (permalink / raw
To: agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
DT binding for the PWM block in Qualcomm IPQ6018 SoC.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
v13:
Updated the file name to match the compatible
Sorted the properties and updated the order in the required field
Dropped the syscon node from examples
v12:
Picked up the R-b tag
v11:
No change
v10:
No change
v9:
Add 'ranges' property to example (Rob)
Drop label in example (Rob)
v8:
Add size cell to 'reg' (Rob)
v7:
Use 'reg' instead of 'offset' (Rob)
Drop 'clock-names' and 'assigned-clock*' (Bjorn)
Use single cell address/size in example node (Bjorn)
Move '#pwm-cells' lower in example node (Bjorn)
List 'reg' as required
v6:
Device node is child of TCSR; remove phandle (Rob Herring)
Add assigned-clocks/assigned-clock-rates (Uwe Kleine-König)
v5: Use qcom,pwm-regs for phandle instead of direct regs (Bjorn
Andersson, Kathiravan T)
v4: Update the binding example node as well (Rob Herring's bot)
v3: s/qcom,pwm-ipq6018/qcom,ipq6018-pwm/ (Rob Herring)
v2: Make #pwm-cells const (Rob Herring)
.../bindings/pwm/qcom,ipq6018-pwm.yaml | 45 +++++++++++++++++++
1 file changed, 45 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pwm/qcom,ipq6018-pwm.yaml
diff --git a/Documentation/devicetree/bindings/pwm/qcom,ipq6018-pwm.yaml b/Documentation/devicetree/bindings/pwm/qcom,ipq6018-pwm.yaml
new file mode 100644
index 000000000000..6d0d7ed271f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/qcom,ipq6018-pwm.yaml
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/qcom,ipq6018-pwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm IPQ6018 PWM controller
+
+maintainers:
+ - Baruch Siach <baruch@tkos.co.il>
+
+properties:
+ compatible:
+ const: qcom,ipq6018-pwm
+
+ reg:
+ description: Offset of PWM register in the TCSR block.
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ "#pwm-cells":
+ const: 2
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - "#pwm-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+
+ pwm: pwm@a010 {
+ compatible = "qcom,ipq6018-pwm";
+ reg = <0xa010 0x20>;
+ clocks = <&gcc GCC_ADSS_PWM_CLK>;
+ assigned-clocks = <&gcc GCC_ADSS_PWM_CLK>;
+ assigned-clock-rates = <100000000>;
+ #pwm-cells = <2>;
+ };
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018
2023-10-04 9:04 [PATCH V13 0/4] Add PWM support for IPQ chipsets Devi Priya
2023-10-04 9:04 ` [PATCH V13 1/4] pwm: driver for qualcomm ipq6018 pwm block Devi Priya
2023-10-04 9:04 ` [PATCH V13 2/4] dt-bindings: pwm: add IPQ6018 binding Devi Priya
@ 2023-10-04 9:04 ` Devi Priya
2023-10-04 9:20 ` Krzysztof Kozlowski
2023-10-04 9:04 ` [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node Devi Priya
3 siblings, 1 reply; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:04 UTC (permalink / raw
To: agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
Update the binding to include pwm as the child node to TCSR block and
add simple-mfd support for IPQ6018.
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
V13:
Added simple-mfd support for IPQ6018 based devices
Added support to include pwm as the child node to TCSR
Included syscon node found on IPQ6018 to the examples
.../devicetree/bindings/mfd/qcom,tcsr.yaml | 100 ++++++++++++------
1 file changed, 69 insertions(+), 31 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml b/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml
index 33c3d023a106..14267a493b15 100644
--- a/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml
+++ b/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml
@@ -15,41 +15,58 @@ description:
properties:
compatible:
- items:
- - enum:
- - qcom,msm8976-tcsr
- - qcom,msm8998-tcsr
- - qcom,qcs404-tcsr
- - qcom,sc7180-tcsr
- - qcom,sc7280-tcsr
- - qcom,sc8280xp-tcsr
- - qcom,sdm630-tcsr
- - qcom,sdm845-tcsr
- - qcom,sdx55-tcsr
- - qcom,sdx65-tcsr
- - qcom,sm4450-tcsr
- - qcom,sm8150-tcsr
- - qcom,sm8450-tcsr
- - qcom,tcsr-apq8064
- - qcom,tcsr-apq8084
- - qcom,tcsr-ipq5332
- - qcom,tcsr-ipq6018
- - qcom,tcsr-ipq8064
- - qcom,tcsr-ipq8074
- - qcom,tcsr-ipq9574
- - qcom,tcsr-mdm9615
- - qcom,tcsr-msm8226
- - qcom,tcsr-msm8660
- - qcom,tcsr-msm8916
- - qcom,tcsr-msm8953
- - qcom,tcsr-msm8960
- - qcom,tcsr-msm8974
- - qcom,tcsr-msm8996
- - const: syscon
+ oneOf:
+ - items:
+ - enum:
+ - qcom,msm8976-tcsr
+ - qcom,msm8998-tcsr
+ - qcom,qcs404-tcsr
+ - qcom,sc7180-tcsr
+ - qcom,sc7280-tcsr
+ - qcom,sc8280xp-tcsr
+ - qcom,sdm630-tcsr
+ - qcom,sdm845-tcsr
+ - qcom,sdx55-tcsr
+ - qcom,sdx65-tcsr
+ - qcom,sm4450-tcsr
+ - qcom,sm8150-tcsr
+ - qcom,sm8450-tcsr
+ - qcom,tcsr-apq8064
+ - qcom,tcsr-apq8084
+ - qcom,tcsr-ipq5332
+ - qcom,tcsr-ipq6018
+ - qcom,tcsr-ipq8064
+ - qcom,tcsr-ipq8074
+ - qcom,tcsr-ipq9574
+ - qcom,tcsr-mdm9615
+ - qcom,tcsr-msm8226
+ - qcom,tcsr-msm8660
+ - qcom,tcsr-msm8916
+ - qcom,tcsr-msm8953
+ - qcom,tcsr-msm8960
+ - qcom,tcsr-msm8974
+ - qcom,tcsr-msm8996
+ - const: syscon
+ - items:
+ - const: qcom,tcsr-ipq6018
+ - const: syscon
+ - const: simple-mfd
reg:
maxItems: 1
+ ranges: true
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+patternProperties:
+ "pwm@[a-f0-9]+$":
+ $ref: ../pwm/qcom,ipq6018-pwm.yaml
+
required:
- compatible
- reg
@@ -57,8 +74,29 @@ required:
additionalProperties: false
examples:
+ # Example 1 - Syscon node found on MSM8960
- |
syscon@1a400000 {
compatible = "qcom,tcsr-msm8960", "syscon";
reg = <0x1a400000 0x100>;
};
+ # Example 2 - Syscon node found on IPQ6018
+ - |
+ #include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+
+ syscon@1937000 {
+ compatible = "qcom,tcsr-ipq6018", "syscon", "simple-mfd";
+ reg = <0x01937000 0x21000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1937000 0x21000>;
+
+ pwm: pwm@a010 {
+ compatible = "qcom,ipq6018-pwm";
+ reg = <0xa010 0x20>;
+ clocks = <&gcc GCC_ADSS_PWM_CLK>;
+ assigned-clocks = <&gcc GCC_ADSS_PWM_CLK>;
+ assigned-clock-rates = <100000000>;
+ #pwm-cells = <2>;
+ };
+ };
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node
2023-10-04 9:04 [PATCH V13 0/4] Add PWM support for IPQ chipsets Devi Priya
` (2 preceding siblings ...)
2023-10-04 9:04 ` [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018 Devi Priya
@ 2023-10-04 9:04 ` Devi Priya
2023-10-04 9:43 ` Krzysztof Kozlowski
3 siblings, 1 reply; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:04 UTC (permalink / raw
To: agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
Describe the PWM block on IPQ6018.
The PWM is in the TCSR area. Make &tcsr "simple-mfd" compatible, and add
&pwm as child of &tcsr.
Add also ipq6018 specific compatible string.
Co-developed-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
v13:
No change
v12:
No change
v11:
No change
v10:
No change
v9:
Add 'ranges' property (Rob)
v8:
Add size cell to 'reg' (Rob)
v7:
Use 'reg' instead of 'offset' (Rob)
Add qcom,tcsr-ipq6018 (Rob)
Drop clock-names (Bjorn)
v6:
Make the PWM node child of TCSR (Rob Herring)
Add assigned-clocks/assigned-clock-rates (Uwe Kleine-König)
v5: Use qcom,pwm-regs for TCSR phandle instead of direct regs
v3: s/qcom,pwm-ipq6018/qcom,ipq6018-pwm/ (Rob Herring)
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 ++++++++++++++-
1 file changed, 14 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index e59b9df96c7e..429ad7cb681c 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -390,8 +390,21 @@ tcsr_mutex: hwlock@1905000 {
};
tcsr: syscon@1937000 {
- compatible = "qcom,tcsr-ipq6018", "syscon";
+ compatible = "qcom,tcsr-ipq6018", "syscon", "simple-mfd";
reg = <0x0 0x01937000 0x0 0x21000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x01937000 0x21000>;
+
+ pwm: pwm@a010 {
+ compatible = "qcom,ipq6018-pwm";
+ reg = <0xa010 0x20>;
+ clocks = <&gcc GCC_ADSS_PWM_CLK>;
+ assigned-clocks = <&gcc GCC_ADSS_PWM_CLK>;
+ assigned-clock-rates = <100000000>;
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
};
usb2: usb@70f8800 {
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V13 2/4] dt-bindings: pwm: add IPQ6018 binding
2023-10-04 9:04 ` [PATCH V13 2/4] dt-bindings: pwm: add IPQ6018 binding Devi Priya
@ 2023-10-04 9:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2023-10-04 9:13 UTC (permalink / raw
To: Devi Priya, agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
On 04/10/2023 11:04, Devi Priya wrote:
> DT binding for the PWM block in Qualcomm IPQ6018 SoC.
>
> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Co-developed-by: Baruch Siach <baruch.siach@siklu.com>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
(Although please wait with applying a few hours for Rob's bot to check it)
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018
2023-10-04 9:04 ` [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018 Devi Priya
@ 2023-10-04 9:20 ` Krzysztof Kozlowski
2023-10-04 9:23 ` Devi Priya
0 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2023-10-04 9:20 UTC (permalink / raw
To: Devi Priya, agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
On 04/10/2023 11:04, Devi Priya wrote:
> Update the binding to include pwm as the child node to TCSR block and
> add simple-mfd support for IPQ6018.
>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
Thank you for your patch. There is something to discuss/improve.
> reg:
> maxItems: 1
>
> + ranges: true
> +
> + "#address-cells":
> + const: 1
> +
> + "#size-cells":
> + const: 1
> +
> +patternProperties:
> + "pwm@[a-f0-9]+$":
type: object
> + $ref: ../pwm/qcom,ipq6018-pwm.yaml
This should be full patch, so:
$ref: /schemas/pwm/qcom.......
> +
> required:
> - compatible
> - reg
After required (but before additionalProperties), please add:
allOf:if:then: for other compatible (so use keyword "not:") which will
disallow pwm for them. Disallowing is via:
patternProperties:
"pwm@[a-f0-9]+$": false
See Documentation/devicetree/bindings/interconnect/qcom,rpm.yaml
around line 240. We need something similar.
> @@ -57,8 +74,29 @@ required:
> additionalProperties: false
>
> examples:
> + # Example 1 - Syscon node found on MSM8960
> - |
> syscon@1a400000 {
> compatible = "qcom,tcsr-msm8960", "syscon";
> reg = <0x1a400000 0x100>;
> };
> + # Example 2 - Syscon node found on IPQ6018
> + - |
> + #include <dt-bindings/clock/qcom,gcc-ipq6018.h>
> +
> + syscon@1937000 {
> + compatible = "qcom,tcsr-ipq6018", "syscon", "simple-mfd";
> + reg = <0x01937000 0x21000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x1937000 0x21000>;
Please put ranges just after reg.
> +
> + pwm: pwm@a010 {
> + compatible = "qcom,ipq6018-pwm";
> + reg = <0xa010 0x20>;
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018
2023-10-04 9:20 ` Krzysztof Kozlowski
@ 2023-10-04 9:23 ` Devi Priya
0 siblings, 0 replies; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:23 UTC (permalink / raw
To: Krzysztof Kozlowski, agross, andersson, konrad.dybcio, lee,
robh+dt, krzysztof.kozlowski+dt, conor+dt, thierry.reding,
ndesaulniers, trix, baruch, linux-arm-msm, devicetree,
linux-kernel, llvm
On 10/4/2023 2:50 PM, Krzysztof Kozlowski wrote:
> On 04/10/2023 11:04, Devi Priya wrote:
>> Update the binding to include pwm as the child node to TCSR block and
>> add simple-mfd support for IPQ6018.
>>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
>
> Thank you for your patch. There is something to discuss/improve.
>
>
>> reg:
>> maxItems: 1
>>
>> + ranges: true
>> +
>> + "#address-cells":
>> + const: 1
>> +
>> + "#size-cells":
>> + const: 1
>> +
>> +patternProperties:
>> + "pwm@[a-f0-9]+$":
>
> type: object
Okay
>
>> + $ref: ../pwm/qcom,ipq6018-pwm.yaml
>
> This should be full patch, so:
> $ref: /schemas/pwm/qcom.......
okay
>
>
>> +
>> required:
>> - compatible
>> - reg
>
> After required (but before additionalProperties), please add:
>
> allOf:if:then: for other compatible (so use keyword "not:") which will
> disallow pwm for them. Disallowing is via:
>
> patternProperties:
> "pwm@[a-f0-9]+$": false
>
> See Documentation/devicetree/bindings/interconnect/qcom,rpm.yaml
> around line 240. We need something similar.
Sure, will add!
>
>
>> @@ -57,8 +74,29 @@ required:
>> additionalProperties: false
>>
>> examples:
>> + # Example 1 - Syscon node found on MSM8960
>> - |
>> syscon@1a400000 {
>> compatible = "qcom,tcsr-msm8960", "syscon";
>> reg = <0x1a400000 0x100>;
>> };
>> + # Example 2 - Syscon node found on IPQ6018
>> + - |
>> + #include <dt-bindings/clock/qcom,gcc-ipq6018.h>
>> +
>> + syscon@1937000 {
>> + compatible = "qcom,tcsr-ipq6018", "syscon", "simple-mfd";
>> + reg = <0x01937000 0x21000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0 0x1937000 0x21000>;
>
> Please put ranges just after reg.
Sure,okay
Thanks,
Devi Priya
>
>> +
>> + pwm: pwm@a010 {
>> + compatible = "qcom,ipq6018-pwm";
>> + reg = <0xa010 0x20>;
>
> Best regards,
> Krzysztof
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node
2023-10-04 9:04 ` [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node Devi Priya
@ 2023-10-04 9:43 ` Krzysztof Kozlowski
2023-10-04 9:45 ` Devi Priya
0 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2023-10-04 9:43 UTC (permalink / raw
To: Devi Priya, agross, andersson, konrad.dybcio, lee, robh+dt,
krzysztof.kozlowski+dt, conor+dt, thierry.reding, ndesaulniers,
trix, baruch, linux-arm-msm, devicetree, linux-kernel, llvm
On 04/10/2023 11:04, Devi Priya wrote:
> Describe the PWM block on IPQ6018.
>
> The PWM is in the TCSR area. Make &tcsr "simple-mfd" compatible, and add
> &pwm as child of &tcsr.
>
...
> v3: s/qcom,pwm-ipq6018/qcom,ipq6018-pwm/ (Rob Herring)
>
> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 ++++++++++++++-
> 1 file changed, 14 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> index e59b9df96c7e..429ad7cb681c 100644
> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> @@ -390,8 +390,21 @@ tcsr_mutex: hwlock@1905000 {
> };
>
> tcsr: syscon@1937000 {
> - compatible = "qcom,tcsr-ipq6018", "syscon";
> + compatible = "qcom,tcsr-ipq6018", "syscon", "simple-mfd";
> reg = <0x0 0x01937000 0x0 0x21000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x0 0x01937000 0x21000>;
Please put ranges just after reg.
With that:
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node
2023-10-04 9:43 ` Krzysztof Kozlowski
@ 2023-10-04 9:45 ` Devi Priya
0 siblings, 0 replies; 10+ messages in thread
From: Devi Priya @ 2023-10-04 9:45 UTC (permalink / raw
To: Krzysztof Kozlowski, agross, andersson, konrad.dybcio, lee,
robh+dt, krzysztof.kozlowski+dt, conor+dt, thierry.reding,
ndesaulniers, trix, baruch, linux-arm-msm, devicetree,
linux-kernel, llvm
On 10/4/2023 3:13 PM, Krzysztof Kozlowski wrote:
> On 04/10/2023 11:04, Devi Priya wrote:
>> Describe the PWM block on IPQ6018.
>>
>> The PWM is in the TCSR area. Make &tcsr "simple-mfd" compatible, and add
>> &pwm as child of &tcsr.
>>
>
> ...
>
>> v3: s/qcom,pwm-ipq6018/qcom,ipq6018-pwm/ (Rob Herring)
>>
>> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 ++++++++++++++-
>> 1 file changed, 14 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
>> index e59b9df96c7e..429ad7cb681c 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
>> @@ -390,8 +390,21 @@ tcsr_mutex: hwlock@1905000 {
>> };
>>
>> tcsr: syscon@1937000 {
>> - compatible = "qcom,tcsr-ipq6018", "syscon";
>> + compatible = "qcom,tcsr-ipq6018", "syscon", "simple-mfd";
>> reg = <0x0 0x01937000 0x0 0x21000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0x0 0x01937000 0x21000>;
>
> Please put ranges just after reg.
Sure, okay
>
> With that:
>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Thank you!
Regards,
Devi Priya
>
> Best regards,
> Krzysztof
>
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2023-10-04 9:46 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2023-10-04 9:04 [PATCH V13 0/4] Add PWM support for IPQ chipsets Devi Priya
2023-10-04 9:04 ` [PATCH V13 1/4] pwm: driver for qualcomm ipq6018 pwm block Devi Priya
2023-10-04 9:04 ` [PATCH V13 2/4] dt-bindings: pwm: add IPQ6018 binding Devi Priya
2023-10-04 9:13 ` Krzysztof Kozlowski
2023-10-04 9:04 ` [PATCH V13 3/4] dt-bindings: mfd: qcom,tcsr: Add simple-mfd support for IPQ6018 Devi Priya
2023-10-04 9:20 ` Krzysztof Kozlowski
2023-10-04 9:23 ` Devi Priya
2023-10-04 9:04 ` [PATCH V13 4/4] arm64: dts: ipq6018: add pwm node Devi Priya
2023-10-04 9:43 ` Krzysztof Kozlowski
2023-10-04 9:45 ` Devi Priya
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).