* [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
@ 2024-04-03 4:34 Sumit Garg
2024-04-03 4:34 ` [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Schneider Electric Sumit Garg
` (4 more replies)
0 siblings, 5 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-03 4:34 UTC (permalink / raw
To: linux-arm-msm, devicetree
Cc: andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel, Sumit Garg
Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
Box Core board based on the Qualcomm APQ8016E SoC. For more information
refer to the product page [1].
One of the major difference from db410c is serial port where HMIBSC board
uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
configured via gpio99 and gpio100).
Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 1GiB RAM
- 8GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
- USB ethernet adaptors (soldered)
This series is a v2 since v1 of this DTS file has been reviewed on the
U-Boot mailing list [2].
Changes in v5:
- Addressed another nitpick from Stephen.
- Collected Stephen's review tag.
- Warnings reported by Rob's DT check bot aren't related to HMIBSC
board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
still not converted to YAML format.
Changes in v4:
- Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations
of Linux kernel driver. Instead depend on systemd workaround suggested
by Caleb to get expected HMIBSC reset behaviour.
- Incorporated further DT coding style comments from Stephen.
- Warnings reported by Rob's DT check bot aren't related to HMIBSC
board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
still not converted to YAML format.
Changes in v3:
- Picked up tags.
- Fixed further DT schema warnings.
- Configure resin/power button interrupt as falling edge.
- Incorporate DTS coding style comments from Krzysztof and Konrad.
Changes in v2:
- Fix DT schema warnings.
- Incorporate suggestions from Stephan.
- Document UART1 mode GPIOs based mux.
[1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@linaro.org/
Sumit Garg (3):
dt-bindings: vendor-prefixes: Add Schneider Electric
dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
.../devicetree/bindings/arm/qcom.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
4 files changed, 495 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
--
2.34.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Schneider Electric
2024-04-03 4:34 [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
@ 2024-04-03 4:34 ` Sumit Garg
2024-04-03 4:34 ` [PATCH v5 2/3] dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board Sumit Garg
` (3 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-03 4:34 UTC (permalink / raw
To: linux-arm-msm, devicetree
Cc: andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel, Sumit Garg, Krzysztof Kozlowski
Add vendor prefix for Schneider Electric (https://www.se.com/).
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 1a0dc04f1db4..4ef38573e411 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1211,6 +1211,8 @@ patternProperties:
description: Smart Battery System
"^schindler,.*":
description: Schindler
+ "^schneider,.*":
+ description: Schneider Electric
"^seagate,.*":
description: Seagate Technology PLC
"^seeed,.*":
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/3] dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
2024-04-03 4:34 [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
2024-04-03 4:34 ` [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Schneider Electric Sumit Garg
@ 2024-04-03 4:34 ` Sumit Garg
2024-04-03 4:34 ` [PATCH v5 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
` (2 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-03 4:34 UTC (permalink / raw
To: linux-arm-msm, devicetree
Cc: andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel, Sumit Garg, Krzysztof Kozlowski
Document the compatible for the Schneider Electric HMIBSC IIoT edge box
core board based on the Qualcomm APQ8016E SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 1a5fb889a444..c8c91754fe04 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -137,6 +137,7 @@ properties:
- items:
- enum:
- qcom,apq8016-sbc
+ - schneider,apq8016-hmibsc
- const: qcom,apq8016
- items:
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-03 4:34 [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
2024-04-03 4:34 ` [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Schneider Electric Sumit Garg
2024-04-03 4:34 ` [PATCH v5 2/3] dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board Sumit Garg
@ 2024-04-03 4:34 ` Sumit Garg
2024-04-03 14:15 ` [PATCH v5 0/3] " Rob Herring
2024-04-10 6:24 ` Sumit Garg
4 siblings, 0 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-03 4:34 UTC (permalink / raw
To: linux-arm-msm, devicetree
Cc: andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel, Sumit Garg, Jagdish Gediya
Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
Box Core board based on the Qualcomm APQ8016E SoC.
Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 1GiB RAM
- 8GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
- USB ethernet adaptors (soldered)
Co-developed-by: Jagdish Gediya <jagdish.gediya@linaro.org>
Signed-off-by: Jagdish Gediya <jagdish.gediya@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
2 files changed, 492 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 39889d5f8e12..ad55e52e950b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -5,6 +5,7 @@ apq8016-sbc-usb-host-dtbs := apq8016-sbc.dtb apq8016-sbc-usb-host.dtbo
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-usb-host.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3-camera-mezzanine.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8016-schneider-hmibsc.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
new file mode 100644
index 000000000000..75c6137e5a11
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2024, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
+
+/ {
+ model = "Schneider Electric HMIBSC Board";
+ compatible = "schneider,apq8016-hmibsc", "qcom,apq8016";
+
+ aliases {
+ i2c1 = &blsp_i2c6;
+ i2c3 = &blsp_i2c4;
+ i2c4 = &blsp_i2c3;
+ mmc0 = &sdhc_1; /* eMMC */
+ mmc1 = &sdhc_2; /* SD card */
+ serial0 = &blsp_uart1;
+ serial1 = &blsp_uart2;
+ spi0 = &blsp_spi5;
+ usid0 = &pm8916_0;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7533_out>;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-0 = <&msm_key_volp_n_default>;
+ pinctrl-names = "default";
+
+ button {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pm8916_mpps_leds>;
+ pinctrl-names = "default";
+
+ led-1 {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_YELLOW>;
+ gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ led-2 {
+ function = LED_FUNCTION_BLUETOOTH;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+ };
+
+ memory@80000000 {
+ reg = <0 0x80000000 0 0x40000000>;
+ };
+
+ reserved-memory {
+ ramoops@bff00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xbff00000 0x0 0x100000>;
+ record-size = <0x20000>;
+ console-size = <0x20000>;
+ ftrace-size = <0x20000>;
+ ecc-size = <16>;
+ };
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503";
+ reset-gpios = <&pm8916_gpios 1 GPIO_ACTIVE_LOW>;
+ initial-mode = <1>;
+ };
+
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb_id_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c3 {
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+};
+
+&blsp_i2c4 {
+ status = "okay";
+
+ adv_bridge: bridge@39 {
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+ interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+
+ adi,dsi-lanes = <4>;
+ clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+ clock-names = "cec";
+ pd-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+
+ avdd-supply = <&pm8916_l6>;
+ a2vdd-supply = <&pm8916_l6>;
+ dvdd-supply = <&pm8916_l6>;
+ pvdd-supply = <&pm8916_l6>;
+ v1p2-supply = <&pm8916_l6>;
+ v3p3-supply = <&pm8916_l17>;
+
+ pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+ pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+ pinctrl-names = "default","sleep";
+ #sound-dai-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7533_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7533_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&blsp_i2c6 {
+ status = "okay";
+
+ rtc@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ };
+};
+
+&blsp_spi5 {
+ cs-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ tpm@0 {
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <500000>;
+ };
+};
+
+&blsp_uart1 {
+ label = "UART0";
+ status = "okay";
+};
+
+&blsp_uart2 {
+ label = "UART1";
+ status = "okay";
+};
+
+&lpass {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&adv7533_in>;
+};
+
+&pm8916_codec {
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ status = "okay";
+};
+
+&pm8916_gpios {
+ gpio-line-names =
+ "USB_HUB_RESET_N_PM",
+ "USB_SW_SEL_PM",
+ "NC",
+ "NC";
+
+ usb_hub_reset_pm: usb-hub-reset-pm-state {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-disable;
+ output-high;
+ };
+
+ usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-disable;
+ output-low;
+ };
+
+ usb_sw_sel_pm: usb-sw-sel-pm-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <PM8916_GPIO_VPH>;
+ input-disable;
+ output-high;
+ };
+
+ usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <PM8916_GPIO_VPH>;
+ input-disable;
+ output-low;
+ };
+};
+
+&pm8916_mpps {
+ gpio-line-names =
+ "NC",
+ "WLAN_LED_CTRL",
+ "BT_LED_CTRL",
+ "NC";
+
+ pm8916_mpps_leds: pm8916-mpps-state {
+ pins = "mpp2", "mpp3";
+ function = "digital";
+ output-low;
+ };
+};
+
+&pm8916_resin {
+ linux,code = <KEY_POWER>;
+ status = "okay";
+};
+
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
+ pinctrl-names = "default", "sleep";
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&sound {
+ pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
+ pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
+ pinctrl-names = "default", "sleep";
+ model = "HMIBSC";
+ audio-routing =
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+ status = "okay";
+
+ quaternary-dai-link {
+ link-name = "ADV7533";
+ cpu {
+ sound-dai = <&lpass MI2S_QUATERNARY>;
+ };
+ codec {
+ sound-dai = <&adv_bridge 0>;
+ };
+ };
+
+ primary-dai-link {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
+ };
+ };
+
+ tertiary-dai-link {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
+ };
+ };
+};
+
+&tlmm {
+ pinctrl-0 = <&uart1_mux0_rs232_high &uart1_mux1_rs232_low>;
+ pinctrl-names = "default";
+
+ adv7533_int_active: adv533-int-active-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ adv7533_int_suspend: adv7533-int-suspend-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ adv7533_switch_active: adv7533-switch-active-state {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ adv7533_switch_suspend: adv7533-switch-suspend-state {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ msm_key_volp_n_default: msm-key-volp-n-default-state {
+ pins = "gpio107";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ sdc2_cd_default: sdc2-cd-default-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ /*
+ * UART1 being the debug console supports various modes of
+ * operation (RS-232/485/422) controlled via GPIOs configured
+ * mux as follows:
+ *
+ * gpio100 gpio99 UART mode
+ * 0 0 loopback
+ * 0 1 RS-232
+ * 1 0 RS-485
+ * 1 1 RS-422
+ *
+ * The default mode configured here is RS-232 mode.
+ */
+ uart1_mux0_rs232_high: uart1-mux0-rs232-state {
+ bootph-all;
+ pins = "gpio99";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+
+ uart1_mux1_rs232_low: uart1-mux1-rs232-state {
+ bootph-all;
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ usb_id_default: usb-id-default-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&usb {
+ extcon = <&usb_id>, <&usb_id>;
+ pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+ pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+ pinctrl-names = "default", "device";
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
+
+&wcnss {
+ firmware-name = "qcom/apq8016/wcnss.mbn";
+ status = "okay";
+};
+
+&wcnss_ctrl {
+ firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
+};
+
+&wcnss_iris {
+ compatible = "qcom,wcn3620";
+};
+
+&wcnss_mem {
+ status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in msm8916.dtsi */
+
+/*
+ * 2mA drive strength is not enough when connecting multiple
+ * I2C devices with different pull up resistors.
+ */
+&blsp_i2c4_default {
+ drive-strength = <16>;
+};
+
+&blsp_i2c6_default {
+ drive-strength = <16>;
+};
+
+&blsp_uart1_default {
+ bootph-all;
+};
+
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&stm { status = "okay"; };
+&tpiu { status = "okay"; };
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-03 4:34 [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
` (2 preceding siblings ...)
2024-04-03 4:34 ` [PATCH v5 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
@ 2024-04-03 14:15 ` Rob Herring
2024-04-10 6:24 ` Sumit Garg
4 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2024-04-03 14:15 UTC (permalink / raw
To: Sumit Garg
Cc: devicetree, neil.armstrong, caleb.connolly, conor+dt,
pascal.eberhard, krzysztof.kozlowski+dt, stephan, linux-kernel,
benjamin.missey, daniel.thompson, linux-arm-msm, andersson,
dmitry.baryshkov, jimmy.lalande, konrad.dybcio, robh+dt,
laetitia.mariottini, abdou.saker
On Wed, 03 Apr 2024 10:04:13 +0530, Sumit Garg wrote:
> Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> Box Core board based on the Qualcomm APQ8016E SoC. For more information
> refer to the product page [1].
>
> One of the major difference from db410c is serial port where HMIBSC board
> uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> configured via gpio99 and gpio100).
>
> Support for Schneider Electric HMIBSC. Features:
> - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> - 1GiB RAM
> - 8GiB eMMC, SD slot
> - WiFi and Bluetooth
> - 2x Host, 1x Device USB port
> - HDMI
> - Discrete TPM2 chip over SPI
> - USB ethernet adaptors (soldered)
>
> This series is a v2 since v1 of this DTS file has been reviewed on the
> U-Boot mailing list [2].
>
> Changes in v5:
> - Addressed another nitpick from Stephen.
> - Collected Stephen's review tag.
> - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> still not converted to YAML format.
>
> Changes in v4:
> - Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations
> of Linux kernel driver. Instead depend on systemd workaround suggested
> by Caleb to get expected HMIBSC reset behaviour.
> - Incorporated further DT coding style comments from Stephen.
> - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> still not converted to YAML format.
>
> Changes in v3:
> - Picked up tags.
> - Fixed further DT schema warnings.
> - Configure resin/power button interrupt as falling edge.
> - Incorporate DTS coding style comments from Krzysztof and Konrad.
>
> Changes in v2:
> - Fix DT schema warnings.
> - Incorporate suggestions from Stephan.
> - Document UART1 mode GPIOs based mux.
>
> [1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
> [2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@linaro.org/
>
> Sumit Garg (3):
> dt-bindings: vendor-prefixes: Add Schneider Electric
> dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
> arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
>
> .../devicetree/bindings/arm/qcom.yaml | 1 +
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
> 4 files changed, 495 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
>
> --
> 2.34.1
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y qcom/apq8016-schneider-hmibsc.dtb' for 20240403043416.3800259-1-sumit.garg@linaro.org:
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: pmic@0: gpio@c000:gpio-line-names: ['USB_HUB_RESET_N_PM', 'USB_SW_SEL_PM', 'NC', 'NC'] is too short
from schema $id: http://devicetree.org/schemas/mfd/qcom,spmi-pmic.yaml#
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: gpio@c000: gpio-line-names: ['USB_HUB_RESET_N_PM', 'USB_SW_SEL_PM', 'NC', 'NC'] is too short
from schema $id: http://devicetree.org/schemas/pinctrl/qcom,pmic-gpio.yaml#
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/audio-codec@771c000: failed to match any schema with compatible: ['qcom,msm8916-wcd-digital-codec']
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b088000: failed to match any schema with compatible: ['qcom,msm8916-acc']
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b098000: failed to match any schema with compatible: ['qcom,msm8916-acc']
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b0a8000: failed to match any schema with compatible: ['qcom,msm8916-acc']
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b0b8000: failed to match any schema with compatible: ['qcom,msm8916-acc']
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /usb-id: failed to match any schema with compatible: ['linux,extcon-usb-gpio']
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-03 4:34 [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
` (3 preceding siblings ...)
2024-04-03 14:15 ` [PATCH v5 0/3] " Rob Herring
@ 2024-04-10 6:24 ` Sumit Garg
2024-04-19 15:27 ` Sumit Garg
4 siblings, 1 reply; 10+ messages in thread
From: Sumit Garg @ 2024-04-10 6:24 UTC (permalink / raw
To: andersson, konrad.dybcio
Cc: linux-arm-msm, devicetree, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel
Hi Bjorn, Konrad,
On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@linaro.org> wrote:
>
> Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> Box Core board based on the Qualcomm APQ8016E SoC. For more information
> refer to the product page [1].
>
> One of the major difference from db410c is serial port where HMIBSC board
> uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> configured via gpio99 and gpio100).
>
> Support for Schneider Electric HMIBSC. Features:
> - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> - 1GiB RAM
> - 8GiB eMMC, SD slot
> - WiFi and Bluetooth
> - 2x Host, 1x Device USB port
> - HDMI
> - Discrete TPM2 chip over SPI
> - USB ethernet adaptors (soldered)
>
> This series is a v2 since v1 of this DTS file has been reviewed on the
> U-Boot mailing list [2].
>
> Changes in v5:
> - Addressed another nitpick from Stephen.
> - Collected Stephen's review tag.
> - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> still not converted to YAML format.
>
I haven't seen any further comments on this series, can you help to pick it up?
-Sumit
> Changes in v4:
> - Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations
> of Linux kernel driver. Instead depend on systemd workaround suggested
> by Caleb to get expected HMIBSC reset behaviour.
> - Incorporated further DT coding style comments from Stephen.
> - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> still not converted to YAML format.
>
> Changes in v3:
> - Picked up tags.
> - Fixed further DT schema warnings.
> - Configure resin/power button interrupt as falling edge.
> - Incorporate DTS coding style comments from Krzysztof and Konrad.
>
> Changes in v2:
> - Fix DT schema warnings.
> - Incorporate suggestions from Stephan.
> - Document UART1 mode GPIOs based mux.
>
> [1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
> [2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@linaro.org/
>
> Sumit Garg (3):
> dt-bindings: vendor-prefixes: Add Schneider Electric
> dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
> arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
>
> .../devicetree/bindings/arm/qcom.yaml | 1 +
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
> 4 files changed, 495 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
>
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-10 6:24 ` Sumit Garg
@ 2024-04-19 15:27 ` Sumit Garg
2024-04-19 15:31 ` Dmitry Baryshkov
2024-04-29 7:21 ` Sumit Garg
0 siblings, 2 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-19 15:27 UTC (permalink / raw
To: andersson, konrad.dybcio
Cc: linux-arm-msm, devicetree, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel
On Tue, 9 Apr 2024 at 23:24, Sumit Garg <sumit.garg@linaro.org> wrote:
>
> Hi Bjorn, Konrad,
>
> On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@linaro.org> wrote:
> >
> > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> > Box Core board based on the Qualcomm APQ8016E SoC. For more information
> > refer to the product page [1].
> >
> > One of the major difference from db410c is serial port where HMIBSC board
> > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> > configured via gpio99 and gpio100).
> >
> > Support for Schneider Electric HMIBSC. Features:
> > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> > - 1GiB RAM
> > - 8GiB eMMC, SD slot
> > - WiFi and Bluetooth
> > - 2x Host, 1x Device USB port
> > - HDMI
> > - Discrete TPM2 chip over SPI
> > - USB ethernet adaptors (soldered)
> >
> > This series is a v2 since v1 of this DTS file has been reviewed on the
> > U-Boot mailing list [2].
> >
> > Changes in v5:
> > - Addressed another nitpick from Stephen.
> > - Collected Stephen's review tag.
> > - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> > still not converted to YAML format.
> >
>
> I haven't seen any further comments on this series, can you help to pick it up?
Gentle reminder.
-Sumit
>
> > Changes in v4:
> > - Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations
> > of Linux kernel driver. Instead depend on systemd workaround suggested
> > by Caleb to get expected HMIBSC reset behaviour.
> > - Incorporated further DT coding style comments from Stephen.
> > - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> > still not converted to YAML format.
> >
> > Changes in v3:
> > - Picked up tags.
> > - Fixed further DT schema warnings.
> > - Configure resin/power button interrupt as falling edge.
> > - Incorporate DTS coding style comments from Krzysztof and Konrad.
> >
> > Changes in v2:
> > - Fix DT schema warnings.
> > - Incorporate suggestions from Stephan.
> > - Document UART1 mode GPIOs based mux.
> >
> > [1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
> > [2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@linaro.org/
> >
> > Sumit Garg (3):
> > dt-bindings: vendor-prefixes: Add Schneider Electric
> > dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
> > arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
> >
> > .../devicetree/bindings/arm/qcom.yaml | 1 +
> > .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > .../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
> > 4 files changed, 495 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
> >
> > --
> > 2.34.1
> >
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-19 15:27 ` Sumit Garg
@ 2024-04-19 15:31 ` Dmitry Baryshkov
2024-04-19 16:12 ` Sumit Garg
2024-04-29 7:21 ` Sumit Garg
1 sibling, 1 reply; 10+ messages in thread
From: Dmitry Baryshkov @ 2024-04-19 15:31 UTC (permalink / raw
To: Sumit Garg
Cc: andersson, konrad.dybcio, linux-arm-msm, devicetree, robh+dt,
krzysztof.kozlowski+dt, conor+dt, stephan, caleb.connolly,
neil.armstrong, laetitia.mariottini, pascal.eberhard, abdou.saker,
jimmy.lalande, benjamin.missey, daniel.thompson, linux-kernel
On Fri, 19 Apr 2024 at 18:27, Sumit Garg <sumit.garg@linaro.org> wrote:
>
> On Tue, 9 Apr 2024 at 23:24, Sumit Garg <sumit.garg@linaro.org> wrote:
> >
> > Hi Bjorn, Konrad,
> >
> > On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@linaro.org> wrote:
> > >
> > > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> > > Box Core board based on the Qualcomm APQ8016E SoC. For more information
> > > refer to the product page [1].
> > >
> > > One of the major difference from db410c is serial port where HMIBSC board
> > > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> > > configured via gpio99 and gpio100).
> > >
> > > Support for Schneider Electric HMIBSC. Features:
> > > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> > > - 1GiB RAM
> > > - 8GiB eMMC, SD slot
> > > - WiFi and Bluetooth
> > > - 2x Host, 1x Device USB port
> > > - HDMI
> > > - Discrete TPM2 chip over SPI
> > > - USB ethernet adaptors (soldered)
> > >
> > > This series is a v2 since v1 of this DTS file has been reviewed on the
> > > U-Boot mailing list [2].
> > >
> > > Changes in v5:
> > > - Addressed another nitpick from Stephen.
> > > - Collected Stephen's review tag.
> > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> > > still not converted to YAML format.
> > >
> >
> > I haven't seen any further comments on this series, can you help to pick it up?
>
> Gentle reminder.
I see an email from Rob. At least GPIO-related warnings are related to HMIBSC
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-19 15:31 ` Dmitry Baryshkov
@ 2024-04-19 16:12 ` Sumit Garg
0 siblings, 0 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-19 16:12 UTC (permalink / raw
To: Dmitry Baryshkov
Cc: andersson, konrad.dybcio, linux-arm-msm, devicetree, robh+dt,
krzysztof.kozlowski+dt, conor+dt, stephan, caleb.connolly,
neil.armstrong, laetitia.mariottini, pascal.eberhard, abdou.saker,
jimmy.lalande, benjamin.missey, daniel.thompson, linux-kernel
On Fri, 19 Apr 2024 at 08:31, Dmitry Baryshkov
<dmitry.baryshkov@linaro.org> wrote:
>
> On Fri, 19 Apr 2024 at 18:27, Sumit Garg <sumit.garg@linaro.org> wrote:
> >
> > On Tue, 9 Apr 2024 at 23:24, Sumit Garg <sumit.garg@linaro.org> wrote:
> > >
> > > Hi Bjorn, Konrad,
> > >
> > > On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@linaro.org> wrote:
> > > >
> > > > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> > > > Box Core board based on the Qualcomm APQ8016E SoC. For more information
> > > > refer to the product page [1].
> > > >
> > > > One of the major difference from db410c is serial port where HMIBSC board
> > > > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> > > > configured via gpio99 and gpio100).
> > > >
> > > > Support for Schneider Electric HMIBSC. Features:
> > > > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> > > > - 1GiB RAM
> > > > - 8GiB eMMC, SD slot
> > > > - WiFi and Bluetooth
> > > > - 2x Host, 1x Device USB port
> > > > - HDMI
> > > > - Discrete TPM2 chip over SPI
> > > > - USB ethernet adaptors (soldered)
> > > >
> > > > This series is a v2 since v1 of this DTS file has been reviewed on the
> > > > U-Boot mailing list [2].
> > > >
> > > > Changes in v5:
> > > > - Addressed another nitpick from Stephen.
> > > > - Collected Stephen's review tag.
> > > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> > > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> > > > still not converted to YAML format.
> > > >
> > >
> > > I haven't seen any further comments on this series, can you help to pick it up?
> >
> > Gentle reminder.
>
> I see an email from Rob. At least GPIO-related warnings are related to HMIBSC
>
I suppose you are referring to:
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: pmic@0:
gpio@c000:gpio-line-names: ['USB_HUB_RESET_N_PM', 'USB_SW_SEL_PM',
'NC', 'NC'] is too short
from schema $id: http://devicetree.org/schemas/mfd/qcom,spmi-pmic.yaml#
arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: gpio@c000:
gpio-line-names: ['USB_HUB_RESET_N_PM', 'USB_SW_SEL_PM', 'NC', 'NC']
is too short
from schema $id: http://devicetree.org/schemas/pinctrl/qcom,pmic-gpio.yaml#
I am really not sure as to why those warnings are being reported for
v5 and not reported for v4 here [1]. Also, there are only 4 PMIC GPIOs
available on PM8916 out of which only 2 are connected on HMIBSC and
the other 2 are not connected. AFAICT, these seem to be false warning
reports or am I missing something?
[1] https://lore.kernel.org/lkml/171155390164.3454213.14779164019451021567.robh@kernel.org/
-Sumit
>
> --
> With best wishes
> Dmitry
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
2024-04-19 15:27 ` Sumit Garg
2024-04-19 15:31 ` Dmitry Baryshkov
@ 2024-04-29 7:21 ` Sumit Garg
1 sibling, 0 replies; 10+ messages in thread
From: Sumit Garg @ 2024-04-29 7:21 UTC (permalink / raw
To: andersson, konrad.dybcio
Cc: linux-arm-msm, devicetree, robh+dt, krzysztof.kozlowski+dt,
conor+dt, stephan, caleb.connolly, neil.armstrong,
dmitry.baryshkov, laetitia.mariottini, pascal.eberhard,
abdou.saker, jimmy.lalande, benjamin.missey, daniel.thompson,
linux-kernel
On Fri, 19 Apr 2024 at 20:57, Sumit Garg <sumit.garg@linaro.org> wrote:
>
> On Tue, 9 Apr 2024 at 23:24, Sumit Garg <sumit.garg@linaro.org> wrote:
> >
> > Hi Bjorn, Konrad,
> >
> > On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@linaro.org> wrote:
> > >
> > > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> > > Box Core board based on the Qualcomm APQ8016E SoC. For more information
> > > refer to the product page [1].
> > >
> > > One of the major difference from db410c is serial port where HMIBSC board
> > > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> > > configured via gpio99 and gpio100).
> > >
> > > Support for Schneider Electric HMIBSC. Features:
> > > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> > > - 1GiB RAM
> > > - 8GiB eMMC, SD slot
> > > - WiFi and Bluetooth
> > > - 2x Host, 1x Device USB port
> > > - HDMI
> > > - Discrete TPM2 chip over SPI
> > > - USB ethernet adaptors (soldered)
> > >
> > > This series is a v2 since v1 of this DTS file has been reviewed on the
> > > U-Boot mailing list [2].
> > >
> > > Changes in v5:
> > > - Addressed another nitpick from Stephen.
> > > - Collected Stephen's review tag.
> > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> > > still not converted to YAML format.
> > >
> >
> > I haven't seen any further comments on this series, can you help to pick it up?
>
> Gentle reminder.
>
Is there anything missing on my part to get this accepted? It has
already gone through the review cycle with v5 posted for about a month
now.
-Sumit
>
> >
> > > Changes in v4:
> > > - Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations
> > > of Linux kernel driver. Instead depend on systemd workaround suggested
> > > by Caleb to get expected HMIBSC reset behaviour.
> > > - Incorporated further DT coding style comments from Stephen.
> > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC
> > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
> > > still not converted to YAML format.
> > >
> > > Changes in v3:
> > > - Picked up tags.
> > > - Fixed further DT schema warnings.
> > > - Configure resin/power button interrupt as falling edge.
> > > - Incorporate DTS coding style comments from Krzysztof and Konrad.
> > >
> > > Changes in v2:
> > > - Fix DT schema warnings.
> > > - Incorporate suggestions from Stephan.
> > > - Document UART1 mode GPIOs based mux.
> > >
> > > [1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
> > > [2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@linaro.org/
> > >
> > > Sumit Garg (3):
> > > dt-bindings: vendor-prefixes: Add Schneider Electric
> > > dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
> > > arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
> > >
> > > .../devicetree/bindings/arm/qcom.yaml | 1 +
> > > .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> > > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > > .../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
> > > 4 files changed, 495 insertions(+)
> > > create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
> > >
> > > --
> > > 2.34.1
> > >
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2024-04-29 7:21 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-04-03 4:34 [PATCH v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
2024-04-03 4:34 ` [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Schneider Electric Sumit Garg
2024-04-03 4:34 ` [PATCH v5 2/3] dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board Sumit Garg
2024-04-03 4:34 ` [PATCH v5 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS Sumit Garg
2024-04-03 14:15 ` [PATCH v5 0/3] " Rob Herring
2024-04-10 6:24 ` Sumit Garg
2024-04-19 15:27 ` Sumit Garg
2024-04-19 15:31 ` Dmitry Baryshkov
2024-04-19 16:12 ` Sumit Garg
2024-04-29 7:21 ` Sumit Garg
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).