* [PATCH v4 1/4] phy: core: add notify_connect and notify_disconnect callback
@ 2023-12-13 3:10 Stanley Chang
2023-12-13 3:10 ` [PATCH v4 2/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 2.0 PHY Stanley Chang
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Stanley Chang @ 2023-12-13 3:10 UTC (permalink / raw
To: Greg Kroah-Hartman
Cc: Stanley Chang, Vinod Koul, Kishon Vijay Abraham I, Johan Hovold,
Geert Uytterhoeven, Jinjie Ruan, Rob Herring, Alan Stern, Roy Luo,
Ricardo Cañuelo, Heikki Krogerus, linux-kernel, linux-phy,
linux-usb
In Realtek SoC, the parameter of usb phy is designed to be able to
do dynamic tuning based in the port status. Therefore, add a notify
callback of phy driver when usb connection/disconnection change.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
---
v3 to v4 change:
1. Modified some phrasing.
2. Add the description for callback function.
v2 to v3:
No change
v1 to v2:
No change
---
drivers/phy/phy-core.c | 47 +++++++++++++++++++++++++++++++++++++++++
include/linux/phy/phy.h | 21 ++++++++++++++++++
2 files changed, 68 insertions(+)
diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
index 96a0b1e111f3..acfa408a3ca5 100644
--- a/drivers/phy/phy-core.c
+++ b/drivers/phy/phy-core.c
@@ -489,6 +489,53 @@ int phy_calibrate(struct phy *phy)
}
EXPORT_SYMBOL_GPL(phy_calibrate);
+/**
+ * phy_notify_connect() - phy connect notification
+ * @phy: the phy returned by phy_get()
+ * @port: the port index for connect
+ *
+ * If the phy needs to get connection status, the callback can be used.
+ * Returns: %0 if successful, a negative error code otherwise
+ */
+int phy_notify_connect(struct phy *phy, int port)
+{
+ int ret;
+
+ if (!phy || !phy->ops->connect)
+ return 0;
+
+ mutex_lock(&phy->mutex);
+ ret = phy->ops->connect(phy, port);
+ mutex_unlock(&phy->mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(phy_notify_connect);
+
+/**
+ * phy_notify_disconnect() - phy disconnect notification
+ * @phy: the phy returned by phy_get()
+ * @port: the port index for disconnect
+ *
+ * If the phy needs to get connection status, the callback can be used.
+ *
+ * Returns: %0 if successful, a negative error code otherwise
+ */
+int phy_notify_disconnect(struct phy *phy, int port)
+{
+ int ret;
+
+ if (!phy || !phy->ops->disconnect)
+ return 0;
+
+ mutex_lock(&phy->mutex);
+ ret = phy->ops->disconnect(phy, port);
+ mutex_unlock(&phy->mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(phy_notify_disconnect);
+
/**
* phy_configure() - Changes the phy parameters
* @phy: the phy returned by phy_get()
diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
index f6d607ef0e80..aa76609ba258 100644
--- a/include/linux/phy/phy.h
+++ b/include/linux/phy/phy.h
@@ -122,6 +122,11 @@ struct phy_ops {
union phy_configure_opts *opts);
int (*reset)(struct phy *phy);
int (*calibrate)(struct phy *phy);
+
+ /* notify phy connect status change */
+ int (*connect)(struct phy *phy, int port);
+ int (*disconnect)(struct phy *phy, int port);
+
void (*release)(struct phy *phy);
struct module *owner;
};
@@ -243,6 +248,8 @@ static inline enum phy_mode phy_get_mode(struct phy *phy)
}
int phy_reset(struct phy *phy);
int phy_calibrate(struct phy *phy);
+int phy_notify_connect(struct phy *phy, int port);
+int phy_notify_disconnect(struct phy *phy, int port);
static inline int phy_get_bus_width(struct phy *phy)
{
return phy->attrs.bus_width;
@@ -396,6 +403,20 @@ static inline int phy_calibrate(struct phy *phy)
return -ENOSYS;
}
+static inline int phy_notify_connect(struct phy *phy, int index)
+{
+ if (!phy)
+ return 0;
+ return -ENOSYS;
+}
+
+static inline int phy_notify_disconnect(struct phy *phy, int index)
+{
+ if (!phy)
+ return 0;
+ return -ENOSYS;
+}
+
static inline int phy_configure(struct phy *phy,
union phy_configure_opts *opts)
{
--
2.34.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v4 2/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 2.0 PHY
2023-12-13 3:10 [PATCH v4 1/4] phy: core: add notify_connect and notify_disconnect callback Stanley Chang
@ 2023-12-13 3:10 ` Stanley Chang
2023-12-13 3:10 ` [PATCH v4 3/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 3.0 PHY Stanley Chang
2023-12-13 3:10 ` [PATCH v4 4/4] usb: core: add phy notify connect and disconnect Stanley Chang
2 siblings, 0 replies; 6+ messages in thread
From: Stanley Chang @ 2023-12-13 3:10 UTC (permalink / raw
To: Greg Kroah-Hartman
Cc: Stanley Chang, Vinod Koul, Kishon Vijay Abraham I, Johan Hovold,
Geert Uytterhoeven, Rob Herring, Jinjie Ruan, Alan Stern, Roy Luo,
Heikki Krogerus, Ricardo Cañuelo, Flavio Suligoi,
linux-kernel, linux-phy, linux-usb
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.
Note: New driver,remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
---
v3 to v4:
No change
v2 to v3 change:
remove MODULE_ALIAS
v1 to v2 change:
rebase the driver to include the revert part on
7a784bcdd7e54f0599da3b2360e472238412623e
---
drivers/phy/Kconfig | 1 +
drivers/phy/Makefile | 1 +
drivers/phy/realtek/Kconfig | 20 +
drivers/phy/realtek/Makefile | 2 +
drivers/phy/realtek/phy-rtk-usb2.c | 1312 ++++++++++++++++++++++++++++
5 files changed, 1336 insertions(+)
create mode 100644 drivers/phy/realtek/Kconfig
create mode 100644 drivers/phy/realtek/Makefile
create mode 100644 drivers/phy/realtek/phy-rtk-usb2.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 4cef568231bf..787354b849c7 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -87,6 +87,7 @@ source "drivers/phy/motorola/Kconfig"
source "drivers/phy/mscc/Kconfig"
source "drivers/phy/qualcomm/Kconfig"
source "drivers/phy/ralink/Kconfig"
+source "drivers/phy/realtek/Kconfig"
source "drivers/phy/renesas/Kconfig"
source "drivers/phy/rockchip/Kconfig"
source "drivers/phy/samsung/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index fb3dc9de6111..868a220ed0f6 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -26,6 +26,7 @@ obj-y += allwinner/ \
mscc/ \
qualcomm/ \
ralink/ \
+ realtek/ \
renesas/ \
rockchip/ \
samsung/ \
diff --git a/drivers/phy/realtek/Kconfig b/drivers/phy/realtek/Kconfig
new file mode 100644
index 000000000000..745587751070
--- /dev/null
+++ b/drivers/phy/realtek/Kconfig
@@ -0,0 +1,20 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Phy drivers for Realtek platforms
+#
+
+if ARCH_REALTEK || COMPILE_TEST
+
+config PHY_RTK_RTD_USB2PHY
+ tristate "Realtek RTD USB2 PHY Transceiver Driver"
+ depends on USB_SUPPORT
+ select GENERIC_PHY
+ select USB_PHY
+ select USB_COMMON
+ help
+ Enable this to support Realtek SoC USB2 phy transceiver.
+ The DHC (digital home center) RTD series SoCs used the Synopsys
+ DWC3 USB IP. This driver will do the PHY initialization
+ of the parameters.
+
+endif # ARCH_REALTEK || COMPILE_TEST
diff --git a/drivers/phy/realtek/Makefile b/drivers/phy/realtek/Makefile
new file mode 100644
index 000000000000..cf5d440841a2
--- /dev/null
+++ b/drivers/phy/realtek/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_RTK_RTD_USB2PHY) += phy-rtk-usb2.o
diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
new file mode 100644
index 000000000000..e3ad7cea5109
--- /dev/null
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -0,0 +1,1312 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * phy-rtk-usb2.c RTK usb2.0 PHY driver
+ *
+ * Copyright (C) 2023 Realtek Semiconductor Corporation
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/uaccess.h>
+#include <linux/debugfs.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/regmap.h>
+#include <linux/sys_soc.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+#include <linux/usb.h>
+
+/* GUSB2PHYACCn register */
+#define PHY_NEW_REG_REQ BIT(25)
+#define PHY_VSTS_BUSY BIT(23)
+#define PHY_VCTRL_SHIFT 8
+#define PHY_REG_DATA_MASK 0xff
+
+#define GET_LOW_NIBBLE(addr) ((addr) & 0x0f)
+#define GET_HIGH_NIBBLE(addr) (((addr) & 0xf0) >> 4)
+
+#define EFUS_USB_DC_CAL_RATE 2
+#define EFUS_USB_DC_CAL_MAX 7
+
+#define EFUS_USB_DC_DIS_RATE 1
+#define EFUS_USB_DC_DIS_MAX 7
+
+#define MAX_PHY_DATA_SIZE 20
+#define OFFEST_PHY_READ 0x20
+
+#define MAX_USB_PHY_NUM 4
+#define MAX_USB_PHY_PAGE0_DATA_SIZE 16
+#define MAX_USB_PHY_PAGE1_DATA_SIZE 16
+#define MAX_USB_PHY_PAGE2_DATA_SIZE 8
+
+#define SET_PAGE_OFFSET 0xf4
+#define SET_PAGE_0 0x9b
+#define SET_PAGE_1 0xbb
+#define SET_PAGE_2 0xdb
+
+#define PAGE_START 0xe0
+#define PAGE0_0XE4 0xe4
+#define PAGE0_0XE6 0xe6
+#define PAGE0_0XE7 0xe7
+#define PAGE1_0XE0 0xe0
+#define PAGE1_0XE2 0xe2
+
+#define SENSITIVITY_CTRL (BIT(4) | BIT(5) | BIT(6))
+#define ENABLE_AUTO_SENSITIVITY_CALIBRATION BIT(2)
+#define DEFAULT_DC_DRIVING_VALUE (0x8)
+#define DEFAULT_DC_DISCONNECTION_VALUE (0x6)
+#define HS_CLK_SELECT BIT(6)
+
+struct phy_reg {
+ void __iomem *reg_wrap_vstatus;
+ void __iomem *reg_gusb2phyacc0;
+ int vstatus_index;
+};
+
+struct phy_data {
+ u8 addr;
+ u8 data;
+};
+
+struct phy_cfg {
+ int page0_size;
+ struct phy_data page0[MAX_USB_PHY_PAGE0_DATA_SIZE];
+ int page1_size;
+ struct phy_data page1[MAX_USB_PHY_PAGE1_DATA_SIZE];
+ int page2_size;
+ struct phy_data page2[MAX_USB_PHY_PAGE2_DATA_SIZE];
+
+ int num_phy;
+
+ bool check_efuse;
+ int check_efuse_version;
+#define CHECK_EFUSE_V1 1
+#define CHECK_EFUSE_V2 2
+ int efuse_dc_driving_rate;
+ int efuse_dc_disconnect_rate;
+ int dc_driving_mask;
+ int dc_disconnect_mask;
+ bool usb_dc_disconnect_at_page0;
+ int driving_updated_for_dev_dis;
+
+ bool do_toggle;
+ bool do_toggle_driving;
+ bool use_default_parameter;
+ bool is_double_sensitivity_mode;
+};
+
+struct phy_parameter {
+ struct phy_reg phy_reg;
+
+ /* Get from efuse */
+ s8 efuse_usb_dc_cal;
+ s8 efuse_usb_dc_dis;
+
+ /* Get from dts */
+ bool inverse_hstx_sync_clock;
+ u32 driving_level;
+ s32 driving_level_compensate;
+ s32 disconnection_compensate;
+};
+
+struct rtk_phy {
+ struct device *dev;
+
+ struct phy_cfg *phy_cfg;
+ int num_phy;
+ struct phy_parameter *phy_parameter;
+
+ struct dentry *debug_dir;
+};
+
+/* mapping 0xE0 to 0 ... 0xE7 to 7, 0xF0 to 8 ,,, 0xF7 to 15 */
+static inline int page_addr_to_array_index(u8 addr)
+{
+ return (int)((((addr) - PAGE_START) & 0x7) +
+ ((((addr) - PAGE_START) & 0x10) >> 1));
+}
+
+static inline u8 array_index_to_page_addr(int index)
+{
+ return ((((index) + PAGE_START) & 0x7) +
+ ((((index) & 0x8) << 1) + PAGE_START));
+}
+
+#define PHY_IO_TIMEOUT_USEC (50000)
+#define PHY_IO_DELAY_US (100)
+
+static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)
+{
+ int ret;
+ unsigned int val;
+
+ ret = read_poll_timeout(readl, val, ((val & mask) == result),
+ PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg);
+ if (ret) {
+ pr_err("%s can't program USB phy\n", __func__);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
+{
+ void __iomem *reg_gusb2phyacc0 = phy_reg->reg_gusb2phyacc0;
+ unsigned int val;
+ int ret = 0;
+
+ addr -= OFFEST_PHY_READ;
+
+ /* polling until VBusy == 0 */
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return (char)ret;
+
+ /* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return (char)ret;
+
+ /* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return (char)ret;
+
+ val = readl(reg_gusb2phyacc0);
+
+ return (char)(val & PHY_REG_DATA_MASK);
+}
+
+static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
+{
+ unsigned int val;
+ void __iomem *reg_wrap_vstatus = phy_reg->reg_wrap_vstatus;
+ void __iomem *reg_gusb2phyacc0 = phy_reg->reg_gusb2phyacc0;
+ int shift_bits = phy_reg->vstatus_index * 8;
+ int ret = 0;
+
+ /* write data to VStatusOut2 (data output to phy) */
+ writel((u32)data << shift_bits, reg_wrap_vstatus);
+
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return ret;
+
+ /* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return ret;
+
+ /* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtk_phy_set_page(struct phy_reg *phy_reg, int page)
+{
+ switch (page) {
+ case 0:
+ return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_0);
+ case 1:
+ return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_1);
+ case 2:
+ return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_2);
+ default:
+ pr_err("%s error page=%d\n", __func__, page);
+ }
+
+ return -EINVAL;
+}
+
+static u8 __updated_dc_disconnect_level_page0_0xe4(struct phy_cfg *phy_cfg,
+ struct phy_parameter *phy_parameter, u8 data)
+{
+ u8 ret;
+ s32 val;
+ s32 dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+ int offset = 4;
+
+ val = (s32)((data >> offset) & dc_disconnect_mask)
+ + phy_parameter->efuse_usb_dc_dis
+ + phy_parameter->disconnection_compensate;
+
+ if (val > dc_disconnect_mask)
+ val = dc_disconnect_mask;
+ else if (val < 0)
+ val = 0;
+
+ ret = (data & (~(dc_disconnect_mask << offset))) |
+ (val & dc_disconnect_mask) << offset;
+
+ return ret;
+}
+
+/* updated disconnect level at page0 */
+static void update_dc_disconnect_level_at_page0(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, bool update)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+ struct phy_data *phy_data_page;
+ struct phy_data *phy_data;
+ u8 addr, data;
+ int offset = 4;
+ s32 dc_disconnect_mask;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_reg = &phy_parameter->phy_reg;
+
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ i = page_addr_to_array_index(PAGE0_0XE4);
+ phy_data = phy_data_page + i;
+ if (!phy_data->addr) {
+ phy_data->addr = PAGE0_0XE4;
+ phy_data->data = rtk_phy_read(phy_reg, PAGE0_0XE4);
+ }
+
+ addr = phy_data->addr;
+ data = phy_data->data;
+ dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+
+ if (update)
+ data = __updated_dc_disconnect_level_page0_0xe4(phy_cfg, phy_parameter, data);
+ else
+ data = (data & ~(dc_disconnect_mask << offset)) |
+ (DEFAULT_DC_DISCONNECTION_VALUE << offset);
+
+ if (rtk_phy_write(phy_reg, addr, data))
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+}
+
+static u8 __updated_dc_disconnect_level_page1_0xe2(struct phy_cfg *phy_cfg,
+ struct phy_parameter *phy_parameter, u8 data)
+{
+ u8 ret;
+ s32 val;
+ s32 dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ val = (s32)(data & dc_disconnect_mask)
+ + phy_parameter->efuse_usb_dc_dis
+ + phy_parameter->disconnection_compensate;
+ } else { /* for CHECK_EFUSE_V2 or no efuse */
+ if (phy_parameter->efuse_usb_dc_dis)
+ val = (s32)(phy_parameter->efuse_usb_dc_dis +
+ phy_parameter->disconnection_compensate);
+ else
+ val = (s32)((data & dc_disconnect_mask) +
+ phy_parameter->disconnection_compensate);
+ }
+
+ if (val > dc_disconnect_mask)
+ val = dc_disconnect_mask;
+ else if (val < 0)
+ val = 0;
+
+ ret = (data & (~dc_disconnect_mask)) | (val & dc_disconnect_mask);
+
+ return ret;
+}
+
+/* updated disconnect level at page1 */
+static void update_dc_disconnect_level_at_page1(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, bool update)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_data *phy_data_page;
+ struct phy_data *phy_data;
+ struct phy_reg *phy_reg;
+ u8 addr, data;
+ s32 dc_disconnect_mask;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_reg = &phy_parameter->phy_reg;
+
+ /* Set page 1 */
+ phy_data_page = phy_cfg->page1;
+ rtk_phy_set_page(phy_reg, 1);
+
+ i = page_addr_to_array_index(PAGE1_0XE2);
+ phy_data = phy_data_page + i;
+ if (!phy_data->addr) {
+ phy_data->addr = PAGE1_0XE2;
+ phy_data->data = rtk_phy_read(phy_reg, PAGE1_0XE2);
+ }
+
+ addr = phy_data->addr;
+ data = phy_data->data;
+ dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+
+ if (update)
+ data = __updated_dc_disconnect_level_page1_0xe2(phy_cfg, phy_parameter, data);
+ else
+ data = (data & ~dc_disconnect_mask) | DEFAULT_DC_DISCONNECTION_VALUE;
+
+ if (rtk_phy_write(phy_reg, addr, data))
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+}
+
+static void update_dc_disconnect_level(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, bool update)
+{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
+
+ if (phy_cfg->usb_dc_disconnect_at_page0)
+ update_dc_disconnect_level_at_page0(rtk_phy, phy_parameter, update);
+ else
+ update_dc_disconnect_level_at_page1(rtk_phy, phy_parameter, update);
+}
+
+static u8 __update_dc_driving_page0_0xe4(struct phy_cfg *phy_cfg,
+ struct phy_parameter *phy_parameter, u8 data)
+{
+ s32 driving_level_compensate = phy_parameter->driving_level_compensate;
+ s32 dc_driving_mask = phy_cfg->dc_driving_mask;
+ s32 val;
+ u8 ret;
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ val = (s32)(data & dc_driving_mask) + driving_level_compensate
+ + phy_parameter->efuse_usb_dc_cal;
+ } else { /* for CHECK_EFUSE_V2 or no efuse */
+ if (phy_parameter->efuse_usb_dc_cal)
+ val = (s32)((phy_parameter->efuse_usb_dc_cal & dc_driving_mask)
+ + driving_level_compensate);
+ else
+ val = (s32)(data & dc_driving_mask);
+ }
+
+ if (val > dc_driving_mask)
+ val = dc_driving_mask;
+ else if (val < 0)
+ val = 0;
+
+ ret = (data & (~dc_driving_mask)) | (val & dc_driving_mask);
+
+ return ret;
+}
+
+static void update_dc_driving_level(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+
+ phy_reg = &phy_parameter->phy_reg;
+ phy_cfg = rtk_phy->phy_cfg;
+ if (!phy_cfg->page0[4].addr) {
+ rtk_phy_set_page(phy_reg, 0);
+ phy_cfg->page0[4].addr = PAGE0_0XE4;
+ phy_cfg->page0[4].data = rtk_phy_read(phy_reg, PAGE0_0XE4);
+ }
+
+ if (phy_parameter->driving_level != DEFAULT_DC_DRIVING_VALUE) {
+ u32 dc_driving_mask;
+ u8 driving_level;
+ u8 data;
+
+ data = phy_cfg->page0[4].data;
+ dc_driving_mask = phy_cfg->dc_driving_mask;
+ driving_level = data & dc_driving_mask;
+
+ dev_dbg(rtk_phy->dev, "%s driving_level=%d => dts driving_level=%d\n",
+ __func__, driving_level, phy_parameter->driving_level);
+
+ phy_cfg->page0[4].data = (data & (~dc_driving_mask)) |
+ (phy_parameter->driving_level & dc_driving_mask);
+ }
+
+ phy_cfg->page0[4].data = __update_dc_driving_page0_0xe4(phy_cfg,
+ phy_parameter,
+ phy_cfg->page0[4].data);
+}
+
+static void update_hs_clk_select(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (phy_parameter->inverse_hstx_sync_clock) {
+ if (!phy_cfg->page0[6].addr) {
+ rtk_phy_set_page(phy_reg, 0);
+ phy_cfg->page0[6].addr = PAGE0_0XE6;
+ phy_cfg->page0[6].data = rtk_phy_read(phy_reg, PAGE0_0XE6);
+ }
+
+ phy_cfg->page0[6].data = phy_cfg->page0[6].data | HS_CLK_SELECT;
+ }
+}
+
+static void do_rtk_phy_toggle(struct rtk_phy *rtk_phy,
+ int index, bool connect)
+{
+ struct phy_parameter *phy_parameter;
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+ struct phy_data *phy_data_page;
+ u8 addr, data;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (!phy_cfg->do_toggle)
+ goto out;
+
+ if (phy_cfg->is_double_sensitivity_mode)
+ goto do_toggle_driving;
+
+ /* Set page 0 */
+ rtk_phy_set_page(phy_reg, 0);
+
+ addr = PAGE0_0XE7;
+ data = rtk_phy_read(phy_reg, addr);
+
+ if (connect)
+ rtk_phy_write(phy_reg, addr, data & (~SENSITIVITY_CTRL));
+ else
+ rtk_phy_write(phy_reg, addr, data | (SENSITIVITY_CTRL));
+
+do_toggle_driving:
+
+ if (!phy_cfg->do_toggle_driving)
+ goto do_toggle;
+
+ /* Page 0 addr 0xE4 driving capability */
+
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ i = page_addr_to_array_index(PAGE0_0XE4);
+ addr = phy_data_page[i].addr;
+ data = phy_data_page[i].data;
+
+ if (connect) {
+ rtk_phy_write(phy_reg, addr, data);
+ } else {
+ u8 value;
+ s32 tmp;
+ s32 driving_updated =
+ phy_cfg->driving_updated_for_dev_dis;
+ s32 dc_driving_mask = phy_cfg->dc_driving_mask;
+
+ tmp = (s32)(data & dc_driving_mask) + driving_updated;
+
+ if (tmp > dc_driving_mask)
+ tmp = dc_driving_mask;
+ else if (tmp < 0)
+ tmp = 0;
+
+ value = (data & (~dc_driving_mask)) | (tmp & dc_driving_mask);
+
+ rtk_phy_write(phy_reg, addr, value);
+ }
+
+do_toggle:
+ /* restore dc disconnect level before toggle */
+ update_dc_disconnect_level(rtk_phy, phy_parameter, false);
+
+ /* Set page 1 */
+ rtk_phy_set_page(phy_reg, 1);
+
+ addr = PAGE1_0XE0;
+ data = rtk_phy_read(phy_reg, addr);
+
+ rtk_phy_write(phy_reg, addr, data &
+ (~ENABLE_AUTO_SENSITIVITY_CALIBRATION));
+ mdelay(1);
+ rtk_phy_write(phy_reg, addr, data |
+ (ENABLE_AUTO_SENSITIVITY_CALIBRATION));
+
+ /* update dc disconnect level after toggle */
+ update_dc_disconnect_level(rtk_phy, phy_parameter, true);
+
+out:
+ return;
+}
+
+static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
+{
+ struct phy_parameter *phy_parameter;
+ struct phy_cfg *phy_cfg;
+ struct phy_data *phy_data_page;
+ struct phy_reg *phy_reg;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (phy_cfg->use_default_parameter) {
+ dev_dbg(rtk_phy->dev, "%s phy#%d use default parameter\n",
+ __func__, index);
+ goto do_toggle;
+ }
+
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ for (i = 0; i < phy_cfg->page0_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = phy_data->addr;
+ u8 data = phy_data->data;
+
+ if (!addr)
+ continue;
+
+ if (rtk_phy_write(phy_reg, addr, data)) {
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page0 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+ return -EINVAL;
+ }
+ }
+
+ /* Set page 1 */
+ phy_data_page = phy_cfg->page1;
+ rtk_phy_set_page(phy_reg, 1);
+
+ for (i = 0; i < phy_cfg->page1_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = phy_data->addr;
+ u8 data = phy_data->data;
+
+ if (!addr)
+ continue;
+
+ if (rtk_phy_write(phy_reg, addr, data)) {
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+ return -EINVAL;
+ }
+ }
+
+ if (phy_cfg->page2_size == 0)
+ goto do_toggle;
+
+ /* Set page 2 */
+ phy_data_page = phy_cfg->page2;
+ rtk_phy_set_page(phy_reg, 2);
+
+ for (i = 0; i < phy_cfg->page2_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = phy_data->addr;
+ u8 data = phy_data->data;
+
+ if (!addr)
+ continue;
+
+ if (rtk_phy_write(phy_reg, addr, data)) {
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page2 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+ return -EINVAL;
+ }
+ }
+
+do_toggle:
+ do_rtk_phy_toggle(rtk_phy, index, false);
+
+ return 0;
+}
+
+static int rtk_phy_init(struct phy *phy)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+ unsigned long phy_init_time = jiffies;
+ int i, ret = 0;
+
+ if (!rtk_phy)
+ return -EINVAL;
+
+ for (i = 0; i < rtk_phy->num_phy; i++)
+ ret = do_rtk_phy_init(rtk_phy, i);
+
+ dev_dbg(rtk_phy->dev, "Initialized RTK USB 2.0 PHY (take %dms)\n",
+ jiffies_to_msecs(jiffies - phy_init_time));
+ return ret;
+}
+
+static int rtk_phy_exit(struct phy *phy)
+{
+ return 0;
+}
+
+static void rtk_phy_toggle(struct rtk_phy *rtk_phy, bool connect, int port)
+{
+ int index = port;
+
+ if (index > rtk_phy->num_phy) {
+ dev_err(rtk_phy->dev, "%s: The port=%d is not in usb phy (num_phy=%d)\n",
+ __func__, index, rtk_phy->num_phy);
+ return;
+ }
+
+ do_rtk_phy_toggle(rtk_phy, index, connect);
+}
+
+static int rtk_phy_connect(struct phy *phy, int port)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+
+ dev_dbg(rtk_phy->dev, "%s port=%d\n", __func__, port);
+ rtk_phy_toggle(rtk_phy, true, port);
+
+ return 0;
+}
+
+static int rtk_phy_disconnect(struct phy *phy, int port)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+
+ dev_dbg(rtk_phy->dev, "%s port=%d\n", __func__, port);
+ rtk_phy_toggle(rtk_phy, false, port);
+
+ return 0;
+}
+
+static const struct phy_ops ops = {
+ .init = rtk_phy_init,
+ .exit = rtk_phy_exit,
+ .connect = rtk_phy_connect,
+ .disconnect = rtk_phy_disconnect,
+ .owner = THIS_MODULE,
+};
+
+#ifdef CONFIG_DEBUG_FS
+static struct dentry *create_phy_debug_root(void)
+{
+ struct dentry *phy_debug_root;
+
+ phy_debug_root = debugfs_lookup("phy", usb_debug_root);
+ if (!phy_debug_root)
+ phy_debug_root = debugfs_create_dir("phy", usb_debug_root);
+
+ return phy_debug_root;
+}
+
+static int rtk_usb2_parameter_show(struct seq_file *s, void *unused)
+{
+ struct rtk_phy *rtk_phy = s->private;
+ struct phy_cfg *phy_cfg;
+ int i, index;
+
+ phy_cfg = rtk_phy->phy_cfg;
+
+ seq_puts(s, "Property:\n");
+ seq_printf(s, " check_efuse: %s\n",
+ phy_cfg->check_efuse ? "Enable" : "Disable");
+ seq_printf(s, " check_efuse_version: %d\n",
+ phy_cfg->check_efuse_version);
+ seq_printf(s, " efuse_dc_driving_rate: %d\n",
+ phy_cfg->efuse_dc_driving_rate);
+ seq_printf(s, " dc_driving_mask: 0x%x\n",
+ phy_cfg->dc_driving_mask);
+ seq_printf(s, " efuse_dc_disconnect_rate: %d\n",
+ phy_cfg->efuse_dc_disconnect_rate);
+ seq_printf(s, " dc_disconnect_mask: 0x%x\n",
+ phy_cfg->dc_disconnect_mask);
+ seq_printf(s, " usb_dc_disconnect_at_page0: %s\n",
+ phy_cfg->usb_dc_disconnect_at_page0 ? "true" : "false");
+ seq_printf(s, " do_toggle: %s\n",
+ phy_cfg->do_toggle ? "Enable" : "Disable");
+ seq_printf(s, " do_toggle_driving: %s\n",
+ phy_cfg->do_toggle_driving ? "Enable" : "Disable");
+ seq_printf(s, " driving_updated_for_dev_dis: 0x%x\n",
+ phy_cfg->driving_updated_for_dev_dis);
+ seq_printf(s, " use_default_parameter: %s\n",
+ phy_cfg->use_default_parameter ? "Enable" : "Disable");
+ seq_printf(s, " is_double_sensitivity_mode: %s\n",
+ phy_cfg->is_double_sensitivity_mode ? "Enable" : "Disable");
+
+ for (index = 0; index < rtk_phy->num_phy; index++) {
+ struct phy_parameter *phy_parameter;
+ struct phy_reg *phy_reg;
+ struct phy_data *phy_data_page;
+
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ seq_printf(s, "PHY %d:\n", index);
+
+ seq_puts(s, "Page 0:\n");
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ for (i = 0; i < phy_cfg->page0_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = array_index_to_page_addr(i);
+ u8 data = phy_data->data;
+ u8 value = rtk_phy_read(phy_reg, addr);
+
+ if (phy_data->addr)
+ seq_printf(s, " Page 0: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
+ addr, data, value);
+ else
+ seq_printf(s, " Page 0: addr=0x%x data=none ==> read value=0x%02x\n",
+ addr, value);
+ }
+
+ seq_puts(s, "Page 1:\n");
+ /* Set page 1 */
+ phy_data_page = phy_cfg->page1;
+ rtk_phy_set_page(phy_reg, 1);
+
+ for (i = 0; i < phy_cfg->page1_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = array_index_to_page_addr(i);
+ u8 data = phy_data->data;
+ u8 value = rtk_phy_read(phy_reg, addr);
+
+ if (phy_data->addr)
+ seq_printf(s, " Page 1: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
+ addr, data, value);
+ else
+ seq_printf(s, " Page 1: addr=0x%x data=none ==> read value=0x%02x\n",
+ addr, value);
+ }
+
+ if (phy_cfg->page2_size == 0)
+ goto out;
+
+ seq_puts(s, "Page 2:\n");
+ /* Set page 2 */
+ phy_data_page = phy_cfg->page2;
+ rtk_phy_set_page(phy_reg, 2);
+
+ for (i = 0; i < phy_cfg->page2_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = array_index_to_page_addr(i);
+ u8 data = phy_data->data;
+ u8 value = rtk_phy_read(phy_reg, addr);
+
+ if (phy_data->addr)
+ seq_printf(s, " Page 2: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
+ addr, data, value);
+ else
+ seq_printf(s, " Page 2: addr=0x%x data=none ==> read value=0x%02x\n",
+ addr, value);
+ }
+
+out:
+ seq_puts(s, "PHY Property:\n");
+ seq_printf(s, " efuse_usb_dc_cal: %d\n",
+ (int)phy_parameter->efuse_usb_dc_cal);
+ seq_printf(s, " efuse_usb_dc_dis: %d\n",
+ (int)phy_parameter->efuse_usb_dc_dis);
+ seq_printf(s, " inverse_hstx_sync_clock: %s\n",
+ phy_parameter->inverse_hstx_sync_clock ? "Enable" : "Disable");
+ seq_printf(s, " driving_level: %d\n",
+ phy_parameter->driving_level);
+ seq_printf(s, " driving_level_compensate: %d\n",
+ phy_parameter->driving_level_compensate);
+ seq_printf(s, " disconnection_compensate: %d\n",
+ phy_parameter->disconnection_compensate);
+ }
+
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(rtk_usb2_parameter);
+
+static inline void create_debug_files(struct rtk_phy *rtk_phy)
+{
+ struct dentry *phy_debug_root = NULL;
+
+ phy_debug_root = create_phy_debug_root();
+ if (!phy_debug_root)
+ return;
+
+ rtk_phy->debug_dir = debugfs_create_dir(dev_name(rtk_phy->dev),
+ phy_debug_root);
+
+ debugfs_create_file("parameter", 0444, rtk_phy->debug_dir, rtk_phy,
+ &rtk_usb2_parameter_fops);
+}
+
+static inline void remove_debug_files(struct rtk_phy *rtk_phy)
+{
+ debugfs_remove_recursive(rtk_phy->debug_dir);
+}
+#else
+static inline void create_debug_files(struct rtk_phy *rtk_phy) { }
+static inline void remove_debug_files(struct rtk_phy *rtk_phy) { }
+#endif /* CONFIG_DEBUG_FS */
+
+static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, int index)
+{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
+ u8 value = 0;
+ struct nvmem_cell *cell;
+ struct soc_device_attribute rtk_soc_groot[] = {
+ { .family = "Realtek Groot",},
+ { /* empty */ } };
+
+ if (!phy_cfg->check_efuse)
+ goto out;
+
+ /* Read efuse for usb dc cal */
+ cell = nvmem_cell_get(rtk_phy->dev, "usb-dc-cal");
+ if (IS_ERR(cell)) {
+ dev_dbg(rtk_phy->dev, "%s no usb-dc-cal: %ld\n",
+ __func__, PTR_ERR(cell));
+ } else {
+ unsigned char *buf;
+ size_t buf_size;
+
+ buf = nvmem_cell_read(cell, &buf_size);
+ if (!IS_ERR(buf)) {
+ value = buf[0] & phy_cfg->dc_driving_mask;
+ kfree(buf);
+ }
+ nvmem_cell_put(cell);
+ }
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ int rate = phy_cfg->efuse_dc_driving_rate;
+
+ if (value <= EFUS_USB_DC_CAL_MAX)
+ phy_parameter->efuse_usb_dc_cal = (int8_t)(value * rate);
+ else
+ phy_parameter->efuse_usb_dc_cal = -(int8_t)
+ ((EFUS_USB_DC_CAL_MAX & value) * rate);
+
+ if (soc_device_match(rtk_soc_groot)) {
+ dev_dbg(rtk_phy->dev, "For groot IC we need a workaround to adjust efuse_usb_dc_cal\n");
+
+ /* We don't multiple dc_cal_rate=2 for positive dc cal compensate */
+ if (value <= EFUS_USB_DC_CAL_MAX)
+ phy_parameter->efuse_usb_dc_cal = (int8_t)(value);
+
+ /* We set max dc cal compensate is 0x8 if otp is 0x7 */
+ if (value == 0x7)
+ phy_parameter->efuse_usb_dc_cal = (int8_t)(value + 1);
+ }
+ } else { /* for CHECK_EFUSE_V2 */
+ phy_parameter->efuse_usb_dc_cal = value & phy_cfg->dc_driving_mask;
+ }
+
+ /* Read efuse for usb dc disconnect level */
+ value = 0;
+ cell = nvmem_cell_get(rtk_phy->dev, "usb-dc-dis");
+ if (IS_ERR(cell)) {
+ dev_dbg(rtk_phy->dev, "%s no usb-dc-dis: %ld\n",
+ __func__, PTR_ERR(cell));
+ } else {
+ unsigned char *buf;
+ size_t buf_size;
+
+ buf = nvmem_cell_read(cell, &buf_size);
+ if (!IS_ERR(buf)) {
+ value = buf[0] & phy_cfg->dc_disconnect_mask;
+ kfree(buf);
+ }
+ nvmem_cell_put(cell);
+ }
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ int rate = phy_cfg->efuse_dc_disconnect_rate;
+
+ if (value <= EFUS_USB_DC_DIS_MAX)
+ phy_parameter->efuse_usb_dc_dis = (int8_t)(value * rate);
+ else
+ phy_parameter->efuse_usb_dc_dis = -(int8_t)
+ ((EFUS_USB_DC_DIS_MAX & value) * rate);
+ } else { /* for CHECK_EFUSE_V2 */
+ phy_parameter->efuse_usb_dc_dis = value & phy_cfg->dc_disconnect_mask;
+ }
+
+out:
+ return 0;
+}
+
+static int parse_phy_data(struct rtk_phy *rtk_phy)
+{
+ struct device *dev = rtk_phy->dev;
+ struct device_node *np = dev->of_node;
+ struct phy_parameter *phy_parameter;
+ int ret = 0;
+ int index;
+
+ rtk_phy->phy_parameter = devm_kzalloc(dev, sizeof(struct phy_parameter) *
+ rtk_phy->num_phy, GFP_KERNEL);
+ if (!rtk_phy->phy_parameter)
+ return -ENOMEM;
+
+ for (index = 0; index < rtk_phy->num_phy; index++) {
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+
+ phy_parameter->phy_reg.reg_wrap_vstatus = of_iomap(np, 0);
+ phy_parameter->phy_reg.reg_gusb2phyacc0 = of_iomap(np, 1) + index;
+ phy_parameter->phy_reg.vstatus_index = index;
+
+ if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
+ phy_parameter->inverse_hstx_sync_clock = true;
+ else
+ phy_parameter->inverse_hstx_sync_clock = false;
+
+ if (of_property_read_u32_index(np, "realtek,driving-level",
+ index, &phy_parameter->driving_level))
+ phy_parameter->driving_level = DEFAULT_DC_DRIVING_VALUE;
+
+ if (of_property_read_u32_index(np, "realtek,driving-level-compensate",
+ index, &phy_parameter->driving_level_compensate))
+ phy_parameter->driving_level_compensate = 0;
+
+ if (of_property_read_u32_index(np, "realtek,disconnection-compensate",
+ index, &phy_parameter->disconnection_compensate))
+ phy_parameter->disconnection_compensate = 0;
+
+ get_phy_data_by_efuse(rtk_phy, phy_parameter, index);
+
+ update_dc_driving_level(rtk_phy, phy_parameter);
+
+ update_hs_clk_select(rtk_phy, phy_parameter);
+ }
+
+ return ret;
+}
+
+static int rtk_usb2phy_probe(struct platform_device *pdev)
+{
+ struct rtk_phy *rtk_phy;
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct phy_provider *phy_provider;
+ const struct phy_cfg *phy_cfg;
+ int ret = 0;
+
+ phy_cfg = of_device_get_match_data(dev);
+ if (!phy_cfg) {
+ dev_err(dev, "phy config are not assigned!\n");
+ return -EINVAL;
+ }
+
+ rtk_phy = devm_kzalloc(dev, sizeof(*rtk_phy), GFP_KERNEL);
+ if (!rtk_phy)
+ return -ENOMEM;
+
+ rtk_phy->dev = &pdev->dev;
+ rtk_phy->phy_cfg = devm_kzalloc(dev, sizeof(*phy_cfg), GFP_KERNEL);
+
+ memcpy(rtk_phy->phy_cfg, phy_cfg, sizeof(*phy_cfg));
+
+ rtk_phy->num_phy = phy_cfg->num_phy;
+
+ ret = parse_phy_data(rtk_phy);
+ if (ret)
+ goto err;
+
+ platform_set_drvdata(pdev, rtk_phy);
+
+ generic_phy = devm_phy_create(rtk_phy->dev, NULL, &ops);
+ if (IS_ERR(generic_phy))
+ return PTR_ERR(generic_phy);
+
+ phy_set_drvdata(generic_phy, rtk_phy);
+
+ phy_provider = devm_of_phy_provider_register(rtk_phy->dev,
+ of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return PTR_ERR(phy_provider);
+
+ create_debug_files(rtk_phy);
+
+err:
+ return ret;
+}
+
+static void rtk_usb2phy_remove(struct platform_device *pdev)
+{
+ struct rtk_phy *rtk_phy = platform_get_drvdata(pdev);
+
+ remove_debug_files(rtk_phy);
+}
+
+static const struct phy_cfg rtd1295_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0x90},
+ [3] = {0xe3, 0x3a},
+ [4] = {0xe4, 0x68},
+ [6] = {0xe6, 0x91},
+ [13] = {0xf5, 0x81},
+ [15] = {0xf7, 0x02}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 1,
+ .check_efuse = false,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1395_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [4] = {0xe4, 0xac},
+ [13] = {0xf5, 0x00},
+ [15] = {0xf7, 0x02}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 1,
+ .check_efuse = false,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1395_phy_cfg_2port = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [4] = {0xe4, 0xac},
+ [13] = {0xf5, 0x00},
+ [15] = {0xf7, 0x02}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 2,
+ .check_efuse = false,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1619_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [4] = {0xe4, 0x68}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1319_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0x18},
+ [4] = {0xe4, 0x6a},
+ [7] = {0xe7, 0x71},
+ [13] = {0xf5, 0x15},
+ [15] = {0xf7, 0x32}, },
+ .page1_size = 8,
+ .page1 = { [3] = {0xe3, 0x44}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [0] = {0xe0, 0x01}, },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = true,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1312c_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0x14},
+ [4] = {0xe4, 0x67},
+ [5] = {0xe5, 0x55}, },
+ .page1_size = 8,
+ .page1 = { [3] = {0xe3, 0x23},
+ [6] = {0xe6, 0x58}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { /* default parameter */ },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = true,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1619b_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0xa3},
+ [4] = {0xe4, 0xa8},
+ [5] = {0xe5, 0x4f},
+ [6] = {0xe6, 0x02}, },
+ .page1_size = 8,
+ .page1 = { [3] = {0xe3, 0x64}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [7] = {0xe7, 0x45}, },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+ .dc_driving_mask = 0x1f,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = false,
+ .do_toggle = true,
+ .do_toggle_driving = true,
+ .driving_updated_for_dev_dis = 0x8,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1319d_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0xa3},
+ [4] = {0xe4, 0x8e},
+ [5] = {0xe5, 0x4f},
+ [6] = {0xe6, 0x02}, },
+ .page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
+ .page1 = { [14] = {0xf5, 0x1}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [7] = {0xe7, 0x44}, },
+ .check_efuse = true,
+ .num_phy = 1,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+ .dc_driving_mask = 0x1f,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = false,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0x8,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1315e_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0xa3},
+ [4] = {0xe4, 0x8c},
+ [5] = {0xe5, 0x4f},
+ [6] = {0xe6, 0x02}, },
+ .page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
+ .page1 = { [3] = {0xe3, 0x7f},
+ [14] = {0xf5, 0x01}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [7] = {0xe7, 0x44}, },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V2,
+ .efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+ .dc_driving_mask = 0x1f,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = false,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0x8,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct of_device_id usbphy_rtk_dt_match[] = {
+ { .compatible = "realtek,rtd1295-usb2phy", .data = &rtd1295_phy_cfg },
+ { .compatible = "realtek,rtd1312c-usb2phy", .data = &rtd1312c_phy_cfg },
+ { .compatible = "realtek,rtd1315e-usb2phy", .data = &rtd1315e_phy_cfg },
+ { .compatible = "realtek,rtd1319-usb2phy", .data = &rtd1319_phy_cfg },
+ { .compatible = "realtek,rtd1319d-usb2phy", .data = &rtd1319d_phy_cfg },
+ { .compatible = "realtek,rtd1395-usb2phy", .data = &rtd1395_phy_cfg },
+ { .compatible = "realtek,rtd1395-usb2phy-2port", .data = &rtd1395_phy_cfg_2port },
+ { .compatible = "realtek,rtd1619-usb2phy", .data = &rtd1619_phy_cfg },
+ { .compatible = "realtek,rtd1619b-usb2phy", .data = &rtd1619b_phy_cfg },
+ {},
+};
+MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match);
+
+static struct platform_driver rtk_usb2phy_driver = {
+ .probe = rtk_usb2phy_probe,
+ .remove_new = rtk_usb2phy_remove,
+ .driver = {
+ .name = "rtk-usb2phy",
+ .of_match_table = usbphy_rtk_dt_match,
+ },
+};
+
+module_platform_driver(rtk_usb2phy_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stanley Chang <stanley_chang@realtek.com>");
+MODULE_DESCRIPTION("Realtek usb 2.0 phy driver");
--
2.34.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v4 3/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 3.0 PHY
2023-12-13 3:10 [PATCH v4 1/4] phy: core: add notify_connect and notify_disconnect callback Stanley Chang
2023-12-13 3:10 ` [PATCH v4 2/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 2.0 PHY Stanley Chang
@ 2023-12-13 3:10 ` Stanley Chang
2023-12-13 3:10 ` [PATCH v4 4/4] usb: core: add phy notify connect and disconnect Stanley Chang
2 siblings, 0 replies; 6+ messages in thread
From: Stanley Chang @ 2023-12-13 3:10 UTC (permalink / raw
To: Greg Kroah-Hartman
Cc: Stanley Chang, Vinod Koul, Kishon Vijay Abraham I, Johan Hovold,
Geert Uytterhoeven, Jinjie Ruan, Rob Herring, Alan Stern,
Flavio Suligoi, Heikki Krogerus, Ricardo Cañuelo,
linux-kernel, linux-phy, linux-usb
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 3.0 PHY transceivers.
Note: New driver, remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
---
v3 to v4:
No change
v2 to v3 change:
remove MODULE_ALIAS
v1 to v2 change:
rebase the driver to include the revert part on
258ea41c926b7b3a16d0d7aa210a1401c4a1601b
---
drivers/phy/realtek/Kconfig | 12 +
drivers/phy/realtek/Makefile | 1 +
drivers/phy/realtek/phy-rtk-usb3.c | 748 +++++++++++++++++++++++++++++
3 files changed, 761 insertions(+)
create mode 100644 drivers/phy/realtek/phy-rtk-usb3.c
diff --git a/drivers/phy/realtek/Kconfig b/drivers/phy/realtek/Kconfig
index 745587751070..75ac7e7c31ae 100644
--- a/drivers/phy/realtek/Kconfig
+++ b/drivers/phy/realtek/Kconfig
@@ -17,4 +17,16 @@ config PHY_RTK_RTD_USB2PHY
DWC3 USB IP. This driver will do the PHY initialization
of the parameters.
+config PHY_RTK_RTD_USB3PHY
+ tristate "Realtek RTD USB3 PHY Transceiver Driver"
+ depends on USB_SUPPORT
+ select GENERIC_PHY
+ select USB_PHY
+ select USB_COMMON
+ help
+ Enable this to support Realtek SoC USB3 phy transceiver.
+ The DHC (digital home center) RTD series SoCs used the Synopsys
+ DWC3 USB IP. This driver will do the PHY initialization
+ of the parameters.
+
endif # ARCH_REALTEK || COMPILE_TEST
diff --git a/drivers/phy/realtek/Makefile b/drivers/phy/realtek/Makefile
index cf5d440841a2..ed7b47ff8a26 100644
--- a/drivers/phy/realtek/Makefile
+++ b/drivers/phy/realtek/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0
obj-$(CONFIG_PHY_RTK_RTD_USB2PHY) += phy-rtk-usb2.o
+obj-$(CONFIG_PHY_RTK_RTD_USB3PHY) += phy-rtk-usb3.o
diff --git a/drivers/phy/realtek/phy-rtk-usb3.c b/drivers/phy/realtek/phy-rtk-usb3.c
new file mode 100644
index 000000000000..dfcf4b921bba
--- /dev/null
+++ b/drivers/phy/realtek/phy-rtk-usb3.c
@@ -0,0 +1,748 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * phy-rtk-usb3.c RTK usb3.0 phy driver
+ *
+ * copyright (c) 2023 realtek semiconductor corporation
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/uaccess.h>
+#include <linux/debugfs.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/regmap.h>
+#include <linux/sys_soc.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+#include <linux/usb.h>
+
+#define USB_MDIO_CTRL_PHY_BUSY BIT(7)
+#define USB_MDIO_CTRL_PHY_WRITE BIT(0)
+#define USB_MDIO_CTRL_PHY_ADDR_SHIFT 8
+#define USB_MDIO_CTRL_PHY_DATA_SHIFT 16
+
+#define MAX_USB_PHY_DATA_SIZE 0x30
+#define PHY_ADDR_0X09 0x09
+#define PHY_ADDR_0X0B 0x0b
+#define PHY_ADDR_0X0D 0x0d
+#define PHY_ADDR_0X10 0x10
+#define PHY_ADDR_0X1F 0x1f
+#define PHY_ADDR_0X20 0x20
+#define PHY_ADDR_0X21 0x21
+#define PHY_ADDR_0X30 0x30
+
+#define REG_0X09_FORCE_CALIBRATION BIT(9)
+#define REG_0X0B_RX_OFFSET_RANGE_MASK 0xc
+#define REG_0X0D_RX_DEBUG_TEST_EN BIT(6)
+#define REG_0X10_DEBUG_MODE_SETTING 0x3c0
+#define REG_0X10_DEBUG_MODE_SETTING_MASK 0x3f8
+#define REG_0X1F_RX_OFFSET_CODE_MASK 0x1e
+
+#define USB_U3_TX_LFPS_SWING_TRIM_SHIFT 4
+#define USB_U3_TX_LFPS_SWING_TRIM_MASK 0xf
+#define AMPLITUDE_CONTROL_COARSE_MASK 0xff
+#define AMPLITUDE_CONTROL_FINE_MASK 0xffff
+#define AMPLITUDE_CONTROL_COARSE_DEFAULT 0xff
+#define AMPLITUDE_CONTROL_FINE_DEFAULT 0xffff
+
+#define PHY_ADDR_MAP_ARRAY_INDEX(addr) (addr)
+#define ARRAY_INDEX_MAP_PHY_ADDR(index) (index)
+
+struct phy_reg {
+ void __iomem *reg_mdio_ctl;
+};
+
+struct phy_data {
+ u8 addr;
+ u16 data;
+};
+
+struct phy_cfg {
+ int param_size;
+ struct phy_data param[MAX_USB_PHY_DATA_SIZE];
+
+ bool check_efuse;
+ bool do_toggle;
+ bool do_toggle_once;
+ bool use_default_parameter;
+ bool check_rx_front_end_offset;
+};
+
+struct phy_parameter {
+ struct phy_reg phy_reg;
+
+ /* Get from efuse */
+ u8 efuse_usb_u3_tx_lfps_swing_trim;
+
+ /* Get from dts */
+ u32 amplitude_control_coarse;
+ u32 amplitude_control_fine;
+};
+
+struct rtk_phy {
+ struct device *dev;
+
+ struct phy_cfg *phy_cfg;
+ int num_phy;
+ struct phy_parameter *phy_parameter;
+
+ struct dentry *debug_dir;
+};
+
+#define PHY_IO_TIMEOUT_USEC (50000)
+#define PHY_IO_DELAY_US (100)
+
+static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)
+{
+ int ret;
+ unsigned int val;
+
+ ret = read_poll_timeout(readl, val, ((val & mask) == result),
+ PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg);
+ if (ret) {
+ pr_err("%s can't program USB phy\n", __func__);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int rtk_phy3_wait_vbusy(struct phy_reg *phy_reg)
+{
+ return utmi_wait_register(phy_reg->reg_mdio_ctl, USB_MDIO_CTRL_PHY_BUSY, 0);
+}
+
+static u16 rtk_phy_read(struct phy_reg *phy_reg, char addr)
+{
+ unsigned int tmp;
+ u32 value;
+
+ tmp = (addr << USB_MDIO_CTRL_PHY_ADDR_SHIFT);
+
+ writel(tmp, phy_reg->reg_mdio_ctl);
+
+ rtk_phy3_wait_vbusy(phy_reg);
+
+ value = readl(phy_reg->reg_mdio_ctl);
+ value = value >> USB_MDIO_CTRL_PHY_DATA_SHIFT;
+
+ return (u16)value;
+}
+
+static int rtk_phy_write(struct phy_reg *phy_reg, char addr, u16 data)
+{
+ unsigned int val;
+
+ val = USB_MDIO_CTRL_PHY_WRITE |
+ (addr << USB_MDIO_CTRL_PHY_ADDR_SHIFT) |
+ (data << USB_MDIO_CTRL_PHY_DATA_SHIFT);
+
+ writel(val, phy_reg->reg_mdio_ctl);
+
+ rtk_phy3_wait_vbusy(phy_reg);
+
+ return 0;
+}
+
+static void do_rtk_usb3_phy_toggle(struct rtk_phy *rtk_phy, int index, bool connect)
+{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
+ struct phy_reg *phy_reg;
+ struct phy_parameter *phy_parameter;
+ struct phy_data *phy_data;
+ u8 addr;
+ u16 data;
+ int i;
+
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (!phy_cfg->do_toggle)
+ return;
+
+ i = PHY_ADDR_MAP_ARRAY_INDEX(PHY_ADDR_0X09);
+ phy_data = phy_cfg->param + i;
+ addr = phy_data->addr;
+ data = phy_data->data;
+
+ if (!addr && !data) {
+ addr = PHY_ADDR_0X09;
+ data = rtk_phy_read(phy_reg, addr);
+ phy_data->addr = addr;
+ phy_data->data = data;
+ }
+
+ rtk_phy_write(phy_reg, addr, data & (~REG_0X09_FORCE_CALIBRATION));
+ mdelay(1);
+ rtk_phy_write(phy_reg, addr, data | REG_0X09_FORCE_CALIBRATION);
+}
+
+static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+ struct phy_parameter *phy_parameter;
+ int i = 0;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (phy_cfg->use_default_parameter)
+ goto do_toggle;
+
+ for (i = 0; i < phy_cfg->param_size; i++) {
+ struct phy_data *phy_data = phy_cfg->param + i;
+ u8 addr = phy_data->addr;
+ u16 data = phy_data->data;
+
+ if (!addr && !data)
+ continue;
+
+ rtk_phy_write(phy_reg, addr, data);
+ }
+
+do_toggle:
+ if (phy_cfg->do_toggle_once)
+ phy_cfg->do_toggle = true;
+
+ do_rtk_usb3_phy_toggle(rtk_phy, index, false);
+
+ if (phy_cfg->do_toggle_once) {
+ u16 check_value = 0;
+ int count = 10;
+ u16 value_0x0d, value_0x10;
+
+ /* Enable Debug mode by set 0x0D and 0x10 */
+ value_0x0d = rtk_phy_read(phy_reg, PHY_ADDR_0X0D);
+ value_0x10 = rtk_phy_read(phy_reg, PHY_ADDR_0X10);
+
+ rtk_phy_write(phy_reg, PHY_ADDR_0X0D,
+ value_0x0d | REG_0X0D_RX_DEBUG_TEST_EN);
+ rtk_phy_write(phy_reg, PHY_ADDR_0X10,
+ (value_0x10 & ~REG_0X10_DEBUG_MODE_SETTING_MASK) |
+ REG_0X10_DEBUG_MODE_SETTING);
+
+ check_value = rtk_phy_read(phy_reg, PHY_ADDR_0X30);
+
+ while (!(check_value & BIT(15))) {
+ check_value = rtk_phy_read(phy_reg, PHY_ADDR_0X30);
+ mdelay(1);
+ if (count-- < 0)
+ break;
+ }
+
+ if (!(check_value & BIT(15)))
+ dev_info(rtk_phy->dev, "toggle fail addr=0x%02x, data=0x%04x\n",
+ PHY_ADDR_0X30, check_value);
+
+ /* Disable Debug mode by set 0x0D and 0x10 to default*/
+ rtk_phy_write(phy_reg, PHY_ADDR_0X0D, value_0x0d);
+ rtk_phy_write(phy_reg, PHY_ADDR_0X10, value_0x10);
+
+ phy_cfg->do_toggle = false;
+ }
+
+ if (phy_cfg->check_rx_front_end_offset) {
+ u16 rx_offset_code, rx_offset_range;
+ u16 code_mask = REG_0X1F_RX_OFFSET_CODE_MASK;
+ u16 range_mask = REG_0X0B_RX_OFFSET_RANGE_MASK;
+ bool do_update = false;
+
+ rx_offset_code = rtk_phy_read(phy_reg, PHY_ADDR_0X1F);
+ if (((rx_offset_code & code_mask) == 0x0) ||
+ ((rx_offset_code & code_mask) == code_mask))
+ do_update = true;
+
+ rx_offset_range = rtk_phy_read(phy_reg, PHY_ADDR_0X0B);
+ if (((rx_offset_range & range_mask) == range_mask) && do_update) {
+ dev_warn(rtk_phy->dev, "Don't update rx_offset_range (rx_offset_code=0x%x, rx_offset_range=0x%x)\n",
+ rx_offset_code, rx_offset_range);
+ do_update = false;
+ }
+
+ if (do_update) {
+ u16 tmp1, tmp2;
+
+ tmp1 = rx_offset_range & (~range_mask);
+ tmp2 = rx_offset_range & range_mask;
+ tmp2 += (1 << 2);
+ rx_offset_range = tmp1 | (tmp2 & range_mask);
+ rtk_phy_write(phy_reg, PHY_ADDR_0X0B, rx_offset_range);
+ goto do_toggle;
+ }
+ }
+
+ return 0;
+}
+
+static int rtk_phy_init(struct phy *phy)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+ int ret = 0;
+ int i;
+ unsigned long phy_init_time = jiffies;
+
+ for (i = 0; i < rtk_phy->num_phy; i++)
+ ret = do_rtk_phy_init(rtk_phy, i);
+
+ dev_dbg(rtk_phy->dev, "Initialized RTK USB 3.0 PHY (take %dms)\n",
+ jiffies_to_msecs(jiffies - phy_init_time));
+
+ return ret;
+}
+
+static int rtk_phy_exit(struct phy *phy)
+{
+ return 0;
+}
+
+static void rtk_phy_toggle(struct rtk_phy *rtk_phy, bool connect, int port)
+{
+ int index = port;
+
+ if (index > rtk_phy->num_phy) {
+ dev_err(rtk_phy->dev, "%s: The port=%d is not in usb phy (num_phy=%d)\n",
+ __func__, index, rtk_phy->num_phy);
+ return;
+ }
+
+ do_rtk_usb3_phy_toggle(rtk_phy, index, connect);
+}
+
+static int rtk_phy_connect(struct phy *phy, int port)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+
+ dev_dbg(rtk_phy->dev, "%s port=%d\n", __func__, port);
+ rtk_phy_toggle(rtk_phy, true, port);
+
+ return 0;
+}
+
+static int rtk_phy_disconnect(struct phy *phy, int port)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+
+ dev_dbg(rtk_phy->dev, "%s port=%d\n", __func__, port);
+ rtk_phy_toggle(rtk_phy, false, port);
+
+ return 0;
+}
+
+static const struct phy_ops ops = {
+ .init = rtk_phy_init,
+ .exit = rtk_phy_exit,
+ .connect = rtk_phy_connect,
+ .disconnect = rtk_phy_disconnect,
+ .owner = THIS_MODULE,
+};
+
+#ifdef CONFIG_DEBUG_FS
+static struct dentry *create_phy_debug_root(void)
+{
+ struct dentry *phy_debug_root;
+
+ phy_debug_root = debugfs_lookup("phy", usb_debug_root);
+ if (!phy_debug_root)
+ phy_debug_root = debugfs_create_dir("phy", usb_debug_root);
+
+ return phy_debug_root;
+}
+
+static int rtk_usb3_parameter_show(struct seq_file *s, void *unused)
+{
+ struct rtk_phy *rtk_phy = s->private;
+ struct phy_cfg *phy_cfg;
+ int i, index;
+
+ phy_cfg = rtk_phy->phy_cfg;
+
+ seq_puts(s, "Property:\n");
+ seq_printf(s, " check_efuse: %s\n",
+ phy_cfg->check_efuse ? "Enable" : "Disable");
+ seq_printf(s, " do_toggle: %s\n",
+ phy_cfg->do_toggle ? "Enable" : "Disable");
+ seq_printf(s, " do_toggle_once: %s\n",
+ phy_cfg->do_toggle_once ? "Enable" : "Disable");
+ seq_printf(s, " use_default_parameter: %s\n",
+ phy_cfg->use_default_parameter ? "Enable" : "Disable");
+
+ for (index = 0; index < rtk_phy->num_phy; index++) {
+ struct phy_reg *phy_reg;
+ struct phy_parameter *phy_parameter;
+
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ seq_printf(s, "PHY %d:\n", index);
+
+ for (i = 0; i < phy_cfg->param_size; i++) {
+ struct phy_data *phy_data = phy_cfg->param + i;
+ u8 addr = ARRAY_INDEX_MAP_PHY_ADDR(i);
+ u16 data = phy_data->data;
+
+ if (!phy_data->addr && !data)
+ seq_printf(s, " addr = 0x%02x, data = none ==> read value = 0x%04x\n",
+ addr, rtk_phy_read(phy_reg, addr));
+ else
+ seq_printf(s, " addr = 0x%02x, data = 0x%04x ==> read value = 0x%04x\n",
+ addr, data, rtk_phy_read(phy_reg, addr));
+ }
+
+ seq_puts(s, "PHY Property:\n");
+ seq_printf(s, " efuse_usb_u3_tx_lfps_swing_trim: 0x%x\n",
+ (int)phy_parameter->efuse_usb_u3_tx_lfps_swing_trim);
+ seq_printf(s, " amplitude_control_coarse: 0x%x\n",
+ (int)phy_parameter->amplitude_control_coarse);
+ seq_printf(s, " amplitude_control_fine: 0x%x\n",
+ (int)phy_parameter->amplitude_control_fine);
+ }
+
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(rtk_usb3_parameter);
+
+static inline void create_debug_files(struct rtk_phy *rtk_phy)
+{
+ struct dentry *phy_debug_root = NULL;
+
+ phy_debug_root = create_phy_debug_root();
+
+ if (!phy_debug_root)
+ return;
+
+ rtk_phy->debug_dir = debugfs_create_dir(dev_name(rtk_phy->dev), phy_debug_root);
+
+ debugfs_create_file("parameter", 0444, rtk_phy->debug_dir, rtk_phy,
+ &rtk_usb3_parameter_fops);
+}
+
+static inline void remove_debug_files(struct rtk_phy *rtk_phy)
+{
+ debugfs_remove_recursive(rtk_phy->debug_dir);
+}
+#else
+static inline void create_debug_files(struct rtk_phy *rtk_phy) { }
+static inline void remove_debug_files(struct rtk_phy *rtk_phy) { }
+#endif /* CONFIG_DEBUG_FS */
+
+static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, int index)
+{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
+ u8 value = 0;
+ struct nvmem_cell *cell;
+
+ if (!phy_cfg->check_efuse)
+ goto out;
+
+ cell = nvmem_cell_get(rtk_phy->dev, "usb_u3_tx_lfps_swing_trim");
+ if (IS_ERR(cell)) {
+ dev_dbg(rtk_phy->dev, "%s no usb_u3_tx_lfps_swing_trim: %ld\n",
+ __func__, PTR_ERR(cell));
+ } else {
+ unsigned char *buf;
+ size_t buf_size;
+
+ buf = nvmem_cell_read(cell, &buf_size);
+ if (!IS_ERR(buf)) {
+ value = buf[0] & USB_U3_TX_LFPS_SWING_TRIM_MASK;
+ kfree(buf);
+ }
+ nvmem_cell_put(cell);
+ }
+
+ if (value > 0 && value < 0x8)
+ phy_parameter->efuse_usb_u3_tx_lfps_swing_trim = 0x8;
+ else
+ phy_parameter->efuse_usb_u3_tx_lfps_swing_trim = (u8)value;
+
+out:
+ return 0;
+}
+
+static void update_amplitude_control_value(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+
+ phy_reg = &phy_parameter->phy_reg;
+ phy_cfg = rtk_phy->phy_cfg;
+
+ if (phy_parameter->amplitude_control_coarse != AMPLITUDE_CONTROL_COARSE_DEFAULT) {
+ u16 val_mask = AMPLITUDE_CONTROL_COARSE_MASK;
+ u16 data;
+
+ if (!phy_cfg->param[PHY_ADDR_0X20].addr && !phy_cfg->param[PHY_ADDR_0X20].data) {
+ phy_cfg->param[PHY_ADDR_0X20].addr = PHY_ADDR_0X20;
+ data = rtk_phy_read(phy_reg, PHY_ADDR_0X20);
+ } else {
+ data = phy_cfg->param[PHY_ADDR_0X20].data;
+ }
+
+ data &= (~val_mask);
+ data |= (phy_parameter->amplitude_control_coarse & val_mask);
+
+ phy_cfg->param[PHY_ADDR_0X20].data = data;
+ }
+
+ if (phy_parameter->efuse_usb_u3_tx_lfps_swing_trim) {
+ u8 efuse_val = phy_parameter->efuse_usb_u3_tx_lfps_swing_trim;
+ u16 val_mask = USB_U3_TX_LFPS_SWING_TRIM_MASK;
+ int val_shift = USB_U3_TX_LFPS_SWING_TRIM_SHIFT;
+ u16 data;
+
+ if (!phy_cfg->param[PHY_ADDR_0X20].addr && !phy_cfg->param[PHY_ADDR_0X20].data) {
+ phy_cfg->param[PHY_ADDR_0X20].addr = PHY_ADDR_0X20;
+ data = rtk_phy_read(phy_reg, PHY_ADDR_0X20);
+ } else {
+ data = phy_cfg->param[PHY_ADDR_0X20].data;
+ }
+
+ data &= ~(val_mask << val_shift);
+ data |= ((efuse_val & val_mask) << val_shift);
+
+ phy_cfg->param[PHY_ADDR_0X20].data = data;
+ }
+
+ if (phy_parameter->amplitude_control_fine != AMPLITUDE_CONTROL_FINE_DEFAULT) {
+ u16 val_mask = AMPLITUDE_CONTROL_FINE_MASK;
+
+ if (!phy_cfg->param[PHY_ADDR_0X21].addr && !phy_cfg->param[PHY_ADDR_0X21].data)
+ phy_cfg->param[PHY_ADDR_0X21].addr = PHY_ADDR_0X21;
+
+ phy_cfg->param[PHY_ADDR_0X21].data =
+ phy_parameter->amplitude_control_fine & val_mask;
+ }
+}
+
+static int parse_phy_data(struct rtk_phy *rtk_phy)
+{
+ struct device *dev = rtk_phy->dev;
+ struct phy_parameter *phy_parameter;
+ int ret = 0;
+ int index;
+
+ rtk_phy->phy_parameter = devm_kzalloc(dev, sizeof(struct phy_parameter) *
+ rtk_phy->num_phy, GFP_KERNEL);
+ if (!rtk_phy->phy_parameter)
+ return -ENOMEM;
+
+ for (index = 0; index < rtk_phy->num_phy; index++) {
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+
+ phy_parameter->phy_reg.reg_mdio_ctl = of_iomap(dev->of_node, 0) + index;
+
+ /* Amplitude control address 0x20 bit 0 to bit 7 */
+ if (of_property_read_u32(dev->of_node, "realtek,amplitude-control-coarse-tuning",
+ &phy_parameter->amplitude_control_coarse))
+ phy_parameter->amplitude_control_coarse = AMPLITUDE_CONTROL_COARSE_DEFAULT;
+
+ /* Amplitude control address 0x21 bit 0 to bit 16 */
+ if (of_property_read_u32(dev->of_node, "realtek,amplitude-control-fine-tuning",
+ &phy_parameter->amplitude_control_fine))
+ phy_parameter->amplitude_control_fine = AMPLITUDE_CONTROL_FINE_DEFAULT;
+
+ get_phy_data_by_efuse(rtk_phy, phy_parameter, index);
+
+ update_amplitude_control_value(rtk_phy, phy_parameter);
+ }
+
+ return ret;
+}
+
+static int rtk_usb3phy_probe(struct platform_device *pdev)
+{
+ struct rtk_phy *rtk_phy;
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct phy_provider *phy_provider;
+ const struct phy_cfg *phy_cfg;
+ int ret;
+
+ phy_cfg = of_device_get_match_data(dev);
+ if (!phy_cfg) {
+ dev_err(dev, "phy config are not assigned!\n");
+ return -EINVAL;
+ }
+
+ rtk_phy = devm_kzalloc(dev, sizeof(*rtk_phy), GFP_KERNEL);
+ if (!rtk_phy)
+ return -ENOMEM;
+
+ rtk_phy->dev = &pdev->dev;
+ rtk_phy->phy_cfg = devm_kzalloc(dev, sizeof(*phy_cfg), GFP_KERNEL);
+
+ memcpy(rtk_phy->phy_cfg, phy_cfg, sizeof(*phy_cfg));
+
+ rtk_phy->num_phy = 1;
+
+ ret = parse_phy_data(rtk_phy);
+ if (ret)
+ goto err;
+
+ platform_set_drvdata(pdev, rtk_phy);
+
+ generic_phy = devm_phy_create(rtk_phy->dev, NULL, &ops);
+ if (IS_ERR(generic_phy))
+ return PTR_ERR(generic_phy);
+
+ phy_set_drvdata(generic_phy, rtk_phy);
+
+ phy_provider = devm_of_phy_provider_register(rtk_phy->dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return PTR_ERR(phy_provider);
+
+ create_debug_files(rtk_phy);
+
+err:
+ return ret;
+}
+
+static void rtk_usb3phy_remove(struct platform_device *pdev)
+{
+ struct rtk_phy *rtk_phy = platform_get_drvdata(pdev);
+
+ remove_debug_files(rtk_phy);
+}
+
+static const struct phy_cfg rtd1295_phy_cfg = {
+ .param_size = MAX_USB_PHY_DATA_SIZE,
+ .param = { [0] = {0x01, 0x4008}, [1] = {0x01, 0xe046},
+ [2] = {0x02, 0x6046}, [3] = {0x03, 0x2779},
+ [4] = {0x04, 0x72f5}, [5] = {0x05, 0x2ad3},
+ [6] = {0x06, 0x000e}, [7] = {0x07, 0x2e00},
+ [8] = {0x08, 0x3591}, [9] = {0x09, 0x525c},
+ [10] = {0x0a, 0xa600}, [11] = {0x0b, 0xa904},
+ [12] = {0x0c, 0xc000}, [13] = {0x0d, 0xef1c},
+ [14] = {0x0e, 0x2000}, [15] = {0x0f, 0x0000},
+ [16] = {0x10, 0x000c}, [17] = {0x11, 0x4c00},
+ [18] = {0x12, 0xfc00}, [19] = {0x13, 0x0c81},
+ [20] = {0x14, 0xde01}, [21] = {0x15, 0x0000},
+ [22] = {0x16, 0x0000}, [23] = {0x17, 0x0000},
+ [24] = {0x18, 0x0000}, [25] = {0x19, 0x4004},
+ [26] = {0x1a, 0x1260}, [27] = {0x1b, 0xff00},
+ [28] = {0x1c, 0xcb00}, [29] = {0x1d, 0xa03f},
+ [30] = {0x1e, 0xc2e0}, [31] = {0x1f, 0x2807},
+ [32] = {0x20, 0x947a}, [33] = {0x21, 0x88aa},
+ [34] = {0x22, 0x0057}, [35] = {0x23, 0xab66},
+ [36] = {0x24, 0x0800}, [37] = {0x25, 0x0000},
+ [38] = {0x26, 0x040a}, [39] = {0x27, 0x01d6},
+ [40] = {0x28, 0xf8c2}, [41] = {0x29, 0x3080},
+ [42] = {0x2a, 0x3082}, [43] = {0x2b, 0x2078},
+ [44] = {0x2c, 0xffff}, [45] = {0x2d, 0xffff},
+ [46] = {0x2e, 0x0000}, [47] = {0x2f, 0x0040}, },
+ .check_efuse = false,
+ .do_toggle = true,
+ .do_toggle_once = false,
+ .use_default_parameter = false,
+ .check_rx_front_end_offset = false,
+};
+
+static const struct phy_cfg rtd1619_phy_cfg = {
+ .param_size = MAX_USB_PHY_DATA_SIZE,
+ .param = { [8] = {0x08, 0x3591},
+ [38] = {0x26, 0x840b},
+ [40] = {0x28, 0xf842}, },
+ .check_efuse = false,
+ .do_toggle = true,
+ .do_toggle_once = false,
+ .use_default_parameter = false,
+ .check_rx_front_end_offset = false,
+};
+
+static const struct phy_cfg rtd1319_phy_cfg = {
+ .param_size = MAX_USB_PHY_DATA_SIZE,
+ .param = { [1] = {0x01, 0xac86},
+ [6] = {0x06, 0x0003},
+ [9] = {0x09, 0x924c},
+ [10] = {0x0a, 0xa608},
+ [11] = {0x0b, 0xb905},
+ [14] = {0x0e, 0x2010},
+ [32] = {0x20, 0x705a},
+ [33] = {0x21, 0xf645},
+ [34] = {0x22, 0x0013},
+ [35] = {0x23, 0xcb66},
+ [41] = {0x29, 0xff00}, },
+ .check_efuse = true,
+ .do_toggle = true,
+ .do_toggle_once = false,
+ .use_default_parameter = false,
+ .check_rx_front_end_offset = false,
+};
+
+static const struct phy_cfg rtd1619b_phy_cfg = {
+ .param_size = MAX_USB_PHY_DATA_SIZE,
+ .param = { [1] = {0x01, 0xac8c},
+ [6] = {0x06, 0x0017},
+ [9] = {0x09, 0x724c},
+ [10] = {0x0a, 0xb610},
+ [11] = {0x0b, 0xb90d},
+ [13] = {0x0d, 0xef2a},
+ [15] = {0x0f, 0x9050},
+ [16] = {0x10, 0x000c},
+ [32] = {0x20, 0x70ff},
+ [34] = {0x22, 0x0013},
+ [35] = {0x23, 0xdb66},
+ [38] = {0x26, 0x8609},
+ [41] = {0x29, 0xff13},
+ [42] = {0x2a, 0x3070}, },
+ .check_efuse = true,
+ .do_toggle = false,
+ .do_toggle_once = true,
+ .use_default_parameter = false,
+ .check_rx_front_end_offset = false,
+};
+
+static const struct phy_cfg rtd1319d_phy_cfg = {
+ .param_size = MAX_USB_PHY_DATA_SIZE,
+ .param = { [1] = {0x01, 0xac89},
+ [4] = {0x04, 0xf2f5},
+ [6] = {0x06, 0x0017},
+ [9] = {0x09, 0x424c},
+ [10] = {0x0a, 0x9610},
+ [11] = {0x0b, 0x9901},
+ [12] = {0x0c, 0xf000},
+ [13] = {0x0d, 0xef2a},
+ [14] = {0x0e, 0x1000},
+ [15] = {0x0f, 0x9050},
+ [32] = {0x20, 0x7077},
+ [35] = {0x23, 0x0b62},
+ [37] = {0x25, 0x10ec},
+ [42] = {0x2a, 0x3070}, },
+ .check_efuse = true,
+ .do_toggle = false,
+ .do_toggle_once = true,
+ .use_default_parameter = false,
+ .check_rx_front_end_offset = true,
+};
+
+static const struct of_device_id usbphy_rtk_dt_match[] = {
+ { .compatible = "realtek,rtd1295-usb3phy", .data = &rtd1295_phy_cfg },
+ { .compatible = "realtek,rtd1319-usb3phy", .data = &rtd1319_phy_cfg },
+ { .compatible = "realtek,rtd1319d-usb3phy", .data = &rtd1319d_phy_cfg },
+ { .compatible = "realtek,rtd1619-usb3phy", .data = &rtd1619_phy_cfg },
+ { .compatible = "realtek,rtd1619b-usb3phy", .data = &rtd1619b_phy_cfg },
+ {},
+};
+MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match);
+
+static struct platform_driver rtk_usb3phy_driver = {
+ .probe = rtk_usb3phy_probe,
+ .remove_new = rtk_usb3phy_remove,
+ .driver = {
+ .name = "rtk-usb3phy",
+ .of_match_table = usbphy_rtk_dt_match,
+ },
+};
+
+module_platform_driver(rtk_usb3phy_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stanley Chang <stanley_chang@realtek.com>");
+MODULE_DESCRIPTION("Realtek usb 3.0 phy driver");
--
2.34.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v4 4/4] usb: core: add phy notify connect and disconnect
2023-12-13 3:10 [PATCH v4 1/4] phy: core: add notify_connect and notify_disconnect callback Stanley Chang
2023-12-13 3:10 ` [PATCH v4 2/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 2.0 PHY Stanley Chang
2023-12-13 3:10 ` [PATCH v4 3/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 3.0 PHY Stanley Chang
@ 2023-12-13 3:10 ` Stanley Chang
2024-01-09 2:08 ` Stanley Chang[昌育德]
2 siblings, 1 reply; 6+ messages in thread
From: Stanley Chang @ 2023-12-13 3:10 UTC (permalink / raw
To: Greg Kroah-Hartman
Cc: Stanley Chang, Vinod Koul, Kishon Vijay Abraham I, Johan Hovold,
Geert Uytterhoeven, Rob Herring, Jinjie Ruan, Alan Stern, Roy Luo,
Ricardo Cañuelo, Flavio Suligoi, linux-kernel, linux-phy,
linux-usb
In Realtek SoC, the parameter of usb phy is designed to can dynamic
tuning base on port status. Therefore, add a notify callback of generic
phy driver when usb device connect and disconnect change.
The Realtek phy driver is designed to dynamically adjust disconnection
level and calibrate phy parameters. When the device connected bit changes
and when the disconnected bit changes, do connection change notification:
Check if portstatus is USB_PORT_STAT_CONNECTION and portchange is
USB_PORT_STAT_C_CONNECTION.
1. The device is connected, the driver lowers the disconnection level and
calibrates the phy parameters.
2. The device disconnects, the driver increases the disconnect level and
calibrates the phy parameters.
Generic phy driver in usb core framework does not support device connect
and disconnect notifications. Therefore, we add an api to notify phy
the connection changes.
Additionally, the generic phy only specifies primary_hcd in the original
design. Added specific "usb2-phy" on primary_hcd and "usb3-phy" on
shared_hcd.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
---
v3 to v4:
Add the documentation for new phy connect/disconnect functions.
v2 to v3:
No change
v1 to v2 change:
rebase the driver to remove the part of usb phy notify API
---
drivers/usb/core/hcd.c | 14 +++--
drivers/usb/core/hub.c | 29 ++++++++++
drivers/usb/core/phy.c | 120 +++++++++++++++++++++++++++++++++++++++++
drivers/usb/core/phy.h | 3 ++
4 files changed, 162 insertions(+), 4 deletions(-)
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 12b6dfeaf658..992284461ad8 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -2794,10 +2794,16 @@ int usb_add_hcd(struct usb_hcd *hcd,
struct usb_device *rhdev;
struct usb_hcd *shared_hcd;
- if (!hcd->skip_phy_initialization && usb_hcd_is_primary_hcd(hcd)) {
- hcd->phy_roothub = usb_phy_roothub_alloc(hcd->self.sysdev);
- if (IS_ERR(hcd->phy_roothub))
- return PTR_ERR(hcd->phy_roothub);
+ if (!hcd->skip_phy_initialization) {
+ if (usb_hcd_is_primary_hcd(hcd)) {
+ hcd->phy_roothub = usb_phy_roothub_alloc(hcd->self.sysdev);
+ if (IS_ERR(hcd->phy_roothub))
+ return PTR_ERR(hcd->phy_roothub);
+ } else {
+ hcd->phy_roothub = usb_phy_roothub_alloc_usb3_phy(hcd->self.sysdev);
+ if (IS_ERR(hcd->phy_roothub))
+ return PTR_ERR(hcd->phy_roothub);
+ }
retval = usb_phy_roothub_init(hcd->phy_roothub);
if (retval)
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 87480a6e6d93..65c0454ee70a 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -37,6 +37,7 @@
#include <asm/byteorder.h>
#include "hub.h"
+#include "phy.h"
#include "otg_productlist.h"
#define USB_VENDOR_GENESYS_LOGIC 0x05e3
@@ -622,6 +623,34 @@ static int hub_ext_port_status(struct usb_hub *hub, int port1, int type,
ret = 0;
}
mutex_unlock(&hub->status_mutex);
+
+ /*
+ * There is no need to lock status_mutex here, because status_mutex
+ * protects hub->status, and the phy driver only checks the port
+ * status without changing the status.
+ */
+ if (!ret) {
+ struct usb_device *hdev = hub->hdev;
+
+ /*
+ * Only roothub will be notified of connection changes,
+ * since the USB PHY only cares about changes at the next
+ * level.
+ */
+ if (is_root_hub(hdev)) {
+ struct usb_hcd *hcd = bus_to_hcd(hdev->bus);
+ bool connect;
+ bool connect_change;
+
+ connect_change = *change & USB_PORT_STAT_C_CONNECTION;
+ connect = *status & USB_PORT_STAT_CONNECTION;
+ if (connect_change && connect)
+ usb_phy_roothub_notify_connect(hcd->phy_roothub, port1 - 1);
+ else if (connect_change)
+ usb_phy_roothub_notify_disconnect(hcd->phy_roothub, port1 - 1);
+ }
+ }
+
return ret;
}
diff --git a/drivers/usb/core/phy.c b/drivers/usb/core/phy.c
index fb1588e7c282..faa20054ad5a 100644
--- a/drivers/usb/core/phy.c
+++ b/drivers/usb/core/phy.c
@@ -19,6 +19,30 @@ struct usb_phy_roothub {
struct list_head list;
};
+/* Allocate the roothub_entry by specific name of phy */
+static int usb_phy_roothub_add_phy_by_name(struct device *dev, const char *name,
+ struct list_head *list)
+{
+ struct usb_phy_roothub *roothub_entry;
+ struct phy *phy;
+
+ phy = devm_of_phy_get(dev, dev->of_node, name);
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
+
+ roothub_entry = devm_kzalloc(dev, sizeof(*roothub_entry), GFP_KERNEL);
+ if (!roothub_entry)
+ return -ENOMEM;
+
+ INIT_LIST_HEAD(&roothub_entry->list);
+
+ roothub_entry->phy = phy;
+
+ list_add_tail(&roothub_entry->list, list);
+
+ return 0;
+}
+
static int usb_phy_roothub_add_phy(struct device *dev, int index,
struct list_head *list)
{
@@ -65,6 +89,9 @@ struct usb_phy_roothub *usb_phy_roothub_alloc(struct device *dev)
INIT_LIST_HEAD(&phy_roothub->list);
+ if (!usb_phy_roothub_add_phy_by_name(dev, "usb2-phy", &phy_roothub->list))
+ return phy_roothub;
+
for (i = 0; i < num_phys; i++) {
err = usb_phy_roothub_add_phy(dev, i, &phy_roothub->list);
if (err)
@@ -75,6 +102,41 @@ struct usb_phy_roothub *usb_phy_roothub_alloc(struct device *dev)
}
EXPORT_SYMBOL_GPL(usb_phy_roothub_alloc);
+/**
+ * usb_phy_roothub_alloc_usb3_phy - alloc the roothub
+ * @dev: the device of the host controller
+ *
+ * Allocate the usb phy roothub if the host use a generic usb3-phy.
+ *
+ * Return: On success, a pointer to the usb_phy_roothub. Otherwise,
+ * %NULL if no use usb3 phy or %-ENOMEM if out of memory.
+ */
+struct usb_phy_roothub *usb_phy_roothub_alloc_usb3_phy(struct device *dev)
+{
+ struct usb_phy_roothub *phy_roothub;
+ int num_phys;
+
+ if (!IS_ENABLED(CONFIG_GENERIC_PHY))
+ return NULL;
+
+ num_phys = of_count_phandle_with_args(dev->of_node, "phys",
+ "#phy-cells");
+ if (num_phys <= 0)
+ return NULL;
+
+ phy_roothub = devm_kzalloc(dev, sizeof(*phy_roothub), GFP_KERNEL);
+ if (!phy_roothub)
+ return ERR_PTR(-ENOMEM);
+
+ INIT_LIST_HEAD(&phy_roothub->list);
+
+ if (!usb_phy_roothub_add_phy_by_name(dev, "usb3-phy", &phy_roothub->list))
+ return phy_roothub;
+
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(usb_phy_roothub_alloc_usb3_phy);
+
int usb_phy_roothub_init(struct usb_phy_roothub *phy_roothub)
{
struct usb_phy_roothub *roothub_entry;
@@ -172,6 +234,64 @@ int usb_phy_roothub_calibrate(struct usb_phy_roothub *phy_roothub)
}
EXPORT_SYMBOL_GPL(usb_phy_roothub_calibrate);
+/**
+ * usb_phy_roothub_notify_connect() - connect notification
+ * @phy_roothub: the phy of roothub, if the host use a generic phy.
+ * @port: the port index for connect
+ *
+ * If the phy needs to get connection status, the callback can be used.
+ * Returns: %0 if successful, a negative error code otherwise
+ */
+int usb_phy_roothub_notify_connect(struct usb_phy_roothub *phy_roothub, int port)
+{
+ struct usb_phy_roothub *roothub_entry;
+ struct list_head *head;
+ int err;
+
+ if (!phy_roothub)
+ return 0;
+
+ head = &phy_roothub->list;
+
+ list_for_each_entry(roothub_entry, head, list) {
+ err = phy_notify_connect(roothub_entry->phy, port);
+ if (err)
+ return err;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(usb_phy_roothub_notify_connect);
+
+/**
+ * usb_phy_roothub_notify_disconnect() - disconnect notification
+ * @phy_roothub: the phy of roothub, if the host use a generic phy.
+ * @port: the port index for disconnect
+ *
+ * If the phy needs to get connection status, the callback can be used.
+ * Returns: %0 if successful, a negative error code otherwise
+ */
+int usb_phy_roothub_notify_disconnect(struct usb_phy_roothub *phy_roothub, int port)
+{
+ struct usb_phy_roothub *roothub_entry;
+ struct list_head *head;
+ int err;
+
+ if (!phy_roothub)
+ return 0;
+
+ head = &phy_roothub->list;
+
+ list_for_each_entry(roothub_entry, head, list) {
+ err = phy_notify_disconnect(roothub_entry->phy, port);
+ if (err)
+ return err;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(usb_phy_roothub_notify_disconnect);
+
int usb_phy_roothub_power_on(struct usb_phy_roothub *phy_roothub)
{
struct usb_phy_roothub *roothub_entry;
diff --git a/drivers/usb/core/phy.h b/drivers/usb/core/phy.h
index 20a267cd986b..88b49c0ea6b5 100644
--- a/drivers/usb/core/phy.h
+++ b/drivers/usb/core/phy.h
@@ -12,6 +12,7 @@ struct device;
struct usb_phy_roothub;
struct usb_phy_roothub *usb_phy_roothub_alloc(struct device *dev);
+struct usb_phy_roothub *usb_phy_roothub_alloc_usb3_phy(struct device *dev);
int usb_phy_roothub_init(struct usb_phy_roothub *phy_roothub);
int usb_phy_roothub_exit(struct usb_phy_roothub *phy_roothub);
@@ -19,6 +20,8 @@ int usb_phy_roothub_exit(struct usb_phy_roothub *phy_roothub);
int usb_phy_roothub_set_mode(struct usb_phy_roothub *phy_roothub,
enum phy_mode mode);
int usb_phy_roothub_calibrate(struct usb_phy_roothub *phy_roothub);
+int usb_phy_roothub_notify_connect(struct usb_phy_roothub *phy_roothub, int port);
+int usb_phy_roothub_notify_disconnect(struct usb_phy_roothub *phy_roothub, int port);
int usb_phy_roothub_power_on(struct usb_phy_roothub *phy_roothub);
void usb_phy_roothub_power_off(struct usb_phy_roothub *phy_roothub);
--
2.34.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* RE: [PATCH v4 4/4] usb: core: add phy notify connect and disconnect
2023-12-13 3:10 ` [PATCH v4 4/4] usb: core: add phy notify connect and disconnect Stanley Chang
@ 2024-01-09 2:08 ` Stanley Chang[昌育德]
2024-01-09 11:44 ` Greg Kroah-Hartman
0 siblings, 1 reply; 6+ messages in thread
From: Stanley Chang[昌育德] @ 2024-01-09 2:08 UTC (permalink / raw
To: Stanley Chang[昌育德], Greg Kroah-Hartman
Cc: Vinod Koul, Kishon Vijay Abraham I, Johan Hovold,
Geert Uytterhoeven, Rob Herring, Jinjie Ruan, Alan Stern, Roy Luo,
Ricardo Cañuelo, Flavio Suligoi,
linux-kernel@vger.kernel.org, linux-phy@lists.infradead.org,
linux-usb@vger.kernel.org
Hi Greg,
Please help review these series of patches.
Thanks,
Stanley
> In Realtek SoC, the parameter of usb phy is designed to can dynamic tuning
> base on port status. Therefore, add a notify callback of generic phy driver
> when usb device connect and disconnect change.
>
> The Realtek phy driver is designed to dynamically adjust disconnection level
> and calibrate phy parameters. When the device connected bit changes and
> when the disconnected bit changes, do connection change notification:
>
> Check if portstatus is USB_PORT_STAT_CONNECTION and portchange is
> USB_PORT_STAT_C_CONNECTION.
> 1. The device is connected, the driver lowers the disconnection level and
> calibrates the phy parameters.
> 2. The device disconnects, the driver increases the disconnect level and
> calibrates the phy parameters.
>
> Generic phy driver in usb core framework does not support device connect and
> disconnect notifications. Therefore, we add an api to notify phy the connection
> changes.
>
> Additionally, the generic phy only specifies primary_hcd in the original design.
> Added specific "usb2-phy" on primary_hcd and "usb3-phy" on shared_hcd.
>
> Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
> ---
> v3 to v4:
> Add the documentation for new phy connect/disconnect functions.
> v2 to v3:
> No change
> v1 to v2 change:
> rebase the driver to remove the part of usb phy notify API
> ---
> drivers/usb/core/hcd.c | 14 +++--
> drivers/usb/core/hub.c | 29 ++++++++++ drivers/usb/core/phy.c | 120
> +++++++++++++++++++++++++++++++++++++++++
> drivers/usb/core/phy.h | 3 ++
> 4 files changed, 162 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index
> 12b6dfeaf658..992284461ad8 100644
> --- a/drivers/usb/core/hcd.c
> +++ b/drivers/usb/core/hcd.c
> @@ -2794,10 +2794,16 @@ int usb_add_hcd(struct usb_hcd *hcd,
> struct usb_device *rhdev;
> struct usb_hcd *shared_hcd;
>
> - if (!hcd->skip_phy_initialization && usb_hcd_is_primary_hcd(hcd)) {
> - hcd->phy_roothub = usb_phy_roothub_alloc(hcd->self.sysdev);
> - if (IS_ERR(hcd->phy_roothub))
> - return PTR_ERR(hcd->phy_roothub);
> + if (!hcd->skip_phy_initialization) {
> + if (usb_hcd_is_primary_hcd(hcd)) {
> + hcd->phy_roothub = usb_phy_roothub_alloc(hcd->self.sysdev);
> + if (IS_ERR(hcd->phy_roothub))
> + return PTR_ERR(hcd->phy_roothub);
> + } else {
> + hcd->phy_roothub =
> usb_phy_roothub_alloc_usb3_phy(hcd->self.sysdev);
> + if (IS_ERR(hcd->phy_roothub))
> + return PTR_ERR(hcd->phy_roothub);
> + }
>
> retval = usb_phy_roothub_init(hcd->phy_roothub);
> if (retval)
> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index
> 87480a6e6d93..65c0454ee70a 100644
> --- a/drivers/usb/core/hub.c
> +++ b/drivers/usb/core/hub.c
> @@ -37,6 +37,7 @@
> #include <asm/byteorder.h>
>
> #include "hub.h"
> +#include "phy.h"
> #include "otg_productlist.h"
>
> #define USB_VENDOR_GENESYS_LOGIC 0x05e3
> @@ -622,6 +623,34 @@ static int hub_ext_port_status(struct usb_hub *hub,
> int port1, int type,
> ret = 0;
> }
> mutex_unlock(&hub->status_mutex);
> +
> + /*
> + * There is no need to lock status_mutex here, because status_mutex
> + * protects hub->status, and the phy driver only checks the port
> + * status without changing the status.
> + */
> + if (!ret) {
> + struct usb_device *hdev = hub->hdev;
> +
> + /*
> + * Only roothub will be notified of connection changes,
> + * since the USB PHY only cares about changes at the next
> + * level.
> + */
> + if (is_root_hub(hdev)) {
> + struct usb_hcd *hcd = bus_to_hcd(hdev->bus);
> + bool connect;
> + bool connect_change;
> +
> + connect_change = *change &
> USB_PORT_STAT_C_CONNECTION;
> + connect = *status & USB_PORT_STAT_CONNECTION;
> + if (connect_change && connect)
> + usb_phy_roothub_notify_connect(hcd->phy_roothub, port1
> - 1);
> + else if (connect_change)
> + usb_phy_roothub_notify_disconnect(hcd->phy_roothub,
> port1 - 1);
> + }
> + }
> +
> return ret;
> }
>
> diff --git a/drivers/usb/core/phy.c b/drivers/usb/core/phy.c index
> fb1588e7c282..faa20054ad5a 100644
> --- a/drivers/usb/core/phy.c
> +++ b/drivers/usb/core/phy.c
> @@ -19,6 +19,30 @@ struct usb_phy_roothub {
> struct list_head list;
> };
>
> +/* Allocate the roothub_entry by specific name of phy */ static int
> +usb_phy_roothub_add_phy_by_name(struct device *dev, const char *name,
> + struct list_head *list)
> +{
> + struct usb_phy_roothub *roothub_entry;
> + struct phy *phy;
> +
> + phy = devm_of_phy_get(dev, dev->of_node, name);
> + if (IS_ERR(phy))
> + return PTR_ERR(phy);
> +
> + roothub_entry = devm_kzalloc(dev, sizeof(*roothub_entry), GFP_KERNEL);
> + if (!roothub_entry)
> + return -ENOMEM;
> +
> + INIT_LIST_HEAD(&roothub_entry->list);
> +
> + roothub_entry->phy = phy;
> +
> + list_add_tail(&roothub_entry->list, list);
> +
> + return 0;
> +}
> +
> static int usb_phy_roothub_add_phy(struct device *dev, int index,
> struct list_head *list)
> {
> @@ -65,6 +89,9 @@ struct usb_phy_roothub *usb_phy_roothub_alloc(struct
> device *dev)
>
> INIT_LIST_HEAD(&phy_roothub->list);
>
> + if (!usb_phy_roothub_add_phy_by_name(dev, "usb2-phy",
> &phy_roothub->list))
> + return phy_roothub;
> +
> for (i = 0; i < num_phys; i++) {
> err = usb_phy_roothub_add_phy(dev, i, &phy_roothub->list);
> if (err)
> @@ -75,6 +102,41 @@ struct usb_phy_roothub *usb_phy_roothub_alloc(struct
> device *dev) } EXPORT_SYMBOL_GPL(usb_phy_roothub_alloc);
>
> +/**
> + * usb_phy_roothub_alloc_usb3_phy - alloc the roothub
> + * @dev: the device of the host controller
> + *
> + * Allocate the usb phy roothub if the host use a generic usb3-phy.
> + *
> + * Return: On success, a pointer to the usb_phy_roothub. Otherwise,
> + * %NULL if no use usb3 phy or %-ENOMEM if out of memory.
> + */
> +struct usb_phy_roothub *usb_phy_roothub_alloc_usb3_phy(struct device
> +*dev) {
> + struct usb_phy_roothub *phy_roothub;
> + int num_phys;
> +
> + if (!IS_ENABLED(CONFIG_GENERIC_PHY))
> + return NULL;
> +
> + num_phys = of_count_phandle_with_args(dev->of_node, "phys",
> + "#phy-cells");
> + if (num_phys <= 0)
> + return NULL;
> +
> + phy_roothub = devm_kzalloc(dev, sizeof(*phy_roothub), GFP_KERNEL);
> + if (!phy_roothub)
> + return ERR_PTR(-ENOMEM);
> +
> + INIT_LIST_HEAD(&phy_roothub->list);
> +
> + if (!usb_phy_roothub_add_phy_by_name(dev, "usb3-phy",
> &phy_roothub->list))
> + return phy_roothub;
> +
> + return NULL;
> +}
> +EXPORT_SYMBOL_GPL(usb_phy_roothub_alloc_usb3_phy);
> +
> int usb_phy_roothub_init(struct usb_phy_roothub *phy_roothub) {
> struct usb_phy_roothub *roothub_entry; @@ -172,6 +234,64 @@ int
> usb_phy_roothub_calibrate(struct usb_phy_roothub *phy_roothub) }
> EXPORT_SYMBOL_GPL(usb_phy_roothub_calibrate);
>
> +/**
> + * usb_phy_roothub_notify_connect() - connect notification
> + * @phy_roothub: the phy of roothub, if the host use a generic phy.
> + * @port: the port index for connect
> + *
> + * If the phy needs to get connection status, the callback can be used.
> + * Returns: %0 if successful, a negative error code otherwise */ int
> +usb_phy_roothub_notify_connect(struct usb_phy_roothub *phy_roothub, int
> +port) {
> + struct usb_phy_roothub *roothub_entry;
> + struct list_head *head;
> + int err;
> +
> + if (!phy_roothub)
> + return 0;
> +
> + head = &phy_roothub->list;
> +
> + list_for_each_entry(roothub_entry, head, list) {
> + err = phy_notify_connect(roothub_entry->phy, port);
> + if (err)
> + return err;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(usb_phy_roothub_notify_connect);
> +
> +/**
> + * usb_phy_roothub_notify_disconnect() - disconnect notification
> + * @phy_roothub: the phy of roothub, if the host use a generic phy.
> + * @port: the port index for disconnect
> + *
> + * If the phy needs to get connection status, the callback can be used.
> + * Returns: %0 if successful, a negative error code otherwise */ int
> +usb_phy_roothub_notify_disconnect(struct usb_phy_roothub *phy_roothub,
> +int port) {
> + struct usb_phy_roothub *roothub_entry;
> + struct list_head *head;
> + int err;
> +
> + if (!phy_roothub)
> + return 0;
> +
> + head = &phy_roothub->list;
> +
> + list_for_each_entry(roothub_entry, head, list) {
> + err = phy_notify_disconnect(roothub_entry->phy, port);
> + if (err)
> + return err;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(usb_phy_roothub_notify_disconnect);
> +
> int usb_phy_roothub_power_on(struct usb_phy_roothub *phy_roothub) {
> struct usb_phy_roothub *roothub_entry; diff --git a/drivers/usb/core/phy.h
> b/drivers/usb/core/phy.h index 20a267cd986b..88b49c0ea6b5 100644
> --- a/drivers/usb/core/phy.h
> +++ b/drivers/usb/core/phy.h
> @@ -12,6 +12,7 @@ struct device;
> struct usb_phy_roothub;
>
> struct usb_phy_roothub *usb_phy_roothub_alloc(struct device *dev);
> +struct usb_phy_roothub *usb_phy_roothub_alloc_usb3_phy(struct device
> +*dev);
>
> int usb_phy_roothub_init(struct usb_phy_roothub *phy_roothub); int
> usb_phy_roothub_exit(struct usb_phy_roothub *phy_roothub); @@ -19,6 +20,8
> @@ int usb_phy_roothub_exit(struct usb_phy_roothub *phy_roothub); int
> usb_phy_roothub_set_mode(struct usb_phy_roothub *phy_roothub,
> enum phy_mode mode);
> int usb_phy_roothub_calibrate(struct usb_phy_roothub *phy_roothub);
> +int usb_phy_roothub_notify_connect(struct usb_phy_roothub *phy_roothub,
> +int port); int usb_phy_roothub_notify_disconnect(struct usb_phy_roothub
> +*phy_roothub, int port);
> int usb_phy_roothub_power_on(struct usb_phy_roothub *phy_roothub);
> void usb_phy_roothub_power_off(struct usb_phy_roothub *phy_roothub);
>
> --
> 2.34.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4 4/4] usb: core: add phy notify connect and disconnect
2024-01-09 2:08 ` Stanley Chang[昌育德]
@ 2024-01-09 11:44 ` Greg Kroah-Hartman
0 siblings, 0 replies; 6+ messages in thread
From: Greg Kroah-Hartman @ 2024-01-09 11:44 UTC (permalink / raw
To: Stanley Chang[昌育德]
Cc: Vinod Koul, Kishon Vijay Abraham I, Johan Hovold,
Geert Uytterhoeven, Rob Herring, Jinjie Ruan, Alan Stern, Roy Luo,
Ricardo Cañuelo, Flavio Suligoi,
linux-kernel@vger.kernel.org, linux-phy@lists.infradead.org,
linux-usb@vger.kernel.org
On Tue, Jan 09, 2024 at 02:08:57AM +0000, Stanley Chang[昌育德] wrote:
> Hi Greg,
>
> Please help review these series of patches.
I was hoping that someone else would review these, which didn't seem to
happen at all, which is odd for something that I thought many others
wanted to see merged.
It will have to wait until after 6.8-rc1 is out. To also help this out,
please help review other changes that are submitted to the lists as that
will reduce the maintainer load here.
And again, if anyone else cares to see these merged, please help review
them, the Cc: list here is very long...
thanks,
greg k-h
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2024-01-09 11:44 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2023-12-13 3:10 [PATCH v4 1/4] phy: core: add notify_connect and notify_disconnect callback Stanley Chang
2023-12-13 3:10 ` [PATCH v4 2/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 2.0 PHY Stanley Chang
2023-12-13 3:10 ` [PATCH v4 3/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 3.0 PHY Stanley Chang
2023-12-13 3:10 ` [PATCH v4 4/4] usb: core: add phy notify connect and disconnect Stanley Chang
2024-01-09 2:08 ` Stanley Chang[昌育德]
2024-01-09 11:44 ` Greg Kroah-Hartman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).