* PROBLEM: Oops during high ide io loads.
@ 2002-12-19 23:05 David A. Chappel
0 siblings, 0 replies; only message in thread
From: David A. Chappel @ 2002-12-19 23:05 UTC (permalink / raw
To: linux-kernel
Oops occurs under high disk load under stock 2.4.20 kernel
(Alan's version too.)
=========================================================
Oops occurs under high disk usage. Simultaniously ripping of
one cd and creating another iso file off of an nfs share.
(oggenc, cdparanoia, mkisofs, xcdroast) I use and have ide-scsi
compiled into my kernel and have an all-ide system.
=========================================================
[root@Perky root]# cat /proc/version
Linux version 2.4.20 (root@Perky.Davids.local) (gcc version 2.96
20000731 (Red Hat Linux 7.1 2.96-98)) #11 SMP Thu Dec 19
13:00:17 MST 2002
=========================================================
I was able to get a couple pictures: ; )
http://home.attbi.com/~bobzibub/oops/oops1.jpg
http://home.attbi.com/~bobzibub/oops/oops2.jpg
Stack: 00000000 ffffffff ffffffff ffffffff ffffffff 00000001
00000000 de4c0000 de4c1e98 c02c0b95 de4c1e3c 00000001 00000001
c02dfc0c 00000000 de4c0000 de4c1e98 ffffffff ffff0018 ffff0018
ffffffef c0114425 00000010 00000282
Call Trace: [<c0115525>]
Code: f7 f1 50 e8 99 fd ff ff 8b 83 40 df 30 c0 89 83 c0 de 30
c0
<1>Unable to handle kernel paging requiest at virtual address
e0000000 printing eip:
c0209847
*pde = 00000000
=========================================================
[root@Perky root]# cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 998.374
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep
mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1992.29
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 998.374
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep
mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1992.29
=========================================================
[root@Perky root]# cat /proc/modules
=========================================================
(The CDs/ hard drives are attached to the HPT370 not the VIA
adapter)
[root@Perky root]# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
02f8-02ff : serial(auto)
0378-037a : parport0
03c0-03df : vga+
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
c000-c00f : VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
c000-c007 : ide0
c008-c00f : ide1
c400-c41f : VIA Technologies, Inc. USB
c400-c41f : usb-uhci
c800-c81f : VIA Technologies, Inc. USB (#2)
c800-c81f : usb-uhci
cc00-ccff : Linksys Network Everywhere Fast Ethernet 10/100
model NC100
cc00-ccff : tulip
d000-d03f : Ensoniq 5880 AudioPCI
d000-d03f : es1371
d400-d407 : Triones Technologies, Inc. HPT366/368/370/370A/372
d400-d407 : ide2
d800-d803 : Triones Technologies, Inc. HPT366/368/370/370A/372
d802-d802 : ide2
dc00-dc07 : Triones Technologies, Inc. HPT366/368/370/370A/372
dc00-dc07 : ide3
e000-e003 : Triones Technologies, Inc. HPT366/368/370/370A/372
e002-e002 : ide3
e400-e4ff : Triones Technologies, Inc. HPT366/368/370/370A/372
e400-e407 : ide2
e408-e40f : ide3
e410-e4ff : HPT370A
=========================================================
[root@Perky root]# cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-1ffeffff : System RAM
00100000-002b9a95 : Kernel code
002b9a96-0034f45f : Kernel data
1fff0000-1fff2fff : ACPI Non-volatile Storage
1fff3000-1fffffff : ACPI Tables
c0000000-cfffffff : VIA Technologies, Inc. VT82C693A/694x
[Apollo PRO133x]
d0000000-dfffffff : PCI Bus #01
d0000000-d7ffffff : nVidia Corporation NV25 [GeForce4 Ti4400]
d8000000-d807ffff : nVidia Corporation NV25 [GeForce4 Ti4400]
e0000000-e1ffffff : PCI Bus #01
e0000000-e0ffffff : nVidia Corporation NV25 [GeForce4 Ti4400]
e3000000-e30003ff : Linksys Network Everywhere Fast Ethernet
10/100 model NC100
e3000000-e30003ff : tulip
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
[root@Perky root]#
=========================================================
[root@Perky root]# lspci -vvv
bash: lspci: command not found
[root@Perky root]# /sbin/lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo
PRO] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at c0000000 (32-bit, prefetchable)
[size=256M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01,
sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset-
FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo
Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE
(rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 11
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Ethernet controller: Bridgecom, Inc: Unknown device 0985
(rev 11)
Subsystem: Bridgecom, Inc: Unknown device 0574
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min, 63750ns max), cache line size
08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at cc00 [size=256]
Region 1: Memory at e3000000 (32-bit, non-prefetchable)
[size=1K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Multimedia audio controller: Ensoniq CT5880 [AudioPCI]
(rev 02)
Subsystem: Ensoniq: Unknown device 8001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at d000 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Unknown mass storage controller: HighPoint Technologies,
Inc. HPT366/370 UltraDMA 66/100 IDE Controller (rev 04)
Subsystem: HighPoint Technologies, Inc.: Unknown device
0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size
08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d400 [size=8]
Region 1: I/O ports at d800 [size=4]
Region 2: I/O ports at dc00 [size=8]
Region 3: I/O ports at e000 [size=4]
Region 4: I/O ports at e400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation: Unknown
device 0251 (rev a2) (prog-if 00 [VGA])
Subsystem: VISIONTEK: Unknown device 003c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable)
[size=128M]
Region 2: Memory at d8000000 (32-bit, prefetchable)
[size=512K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
[root@Perky root]#
=========================================================
<Extract from System.map>
c0208a30 T ide_scan_pio_blacklist
c0208ab0 T ide_get_best_pio_mode
c0208c10 t init_hwif_data
c0208de0 T drive_is_flashcard
c0208f10 T ide_system_bus_speed
c0208f80 T ide_input_data <-------------------
c0209060 T ide_output_data
c0209130 T atapi_input_bytes
c02091a0 T atapi_output_bytes
c0209210 T drive_is_ready
c0209260 T ide_end_request
c0209370 T ide_set_handler
c0209450 T current_capacity
c0209480 T ide_geninit
c0209510 t atapi_reset_pollfunc
c02095e0 t reset_pollfunc
c0209740 t check_dma_crc
c02097c0 t pre_reset
=========================================================
(gdb) disassemble ide_input_data
Dump of assembler code for function ide_input_data:
0xc0208f80 <ide_input_data>: push %ebp
0xc0208f81 <ide_input_data+1>: mov %esp,%ebp
0xc0208f83 <ide_input_data+3>: push %edi
0xc0208f84 <ide_input_data+4>: push %esi
0xc0208f85 <ide_input_data+5>: push %ebx
0xc0208f86 <ide_input_data+6>: sub $0xc,%esp
0xc0208f89 <ide_input_data+9>: mov 0x8(%ebp),%esi
0xc0208f8c <ide_input_data+12>: mov 0xc(%ebp),%edi
0xc0208f8f <ide_input_data+15>: mov 0x10(%ebp),%ebx
0xc0208f92 <ide_input_data+18>: mov 0xfc(%esi),%edx
0xc0208f98 <ide_input_data+24>: mov 0x320(%edx),%eax
0xc0208f9e <ide_input_data+30>: mov %edx,%ecx
0xc0208fa0 <ide_input_data+32>: test %eax,%eax
0xc0208fa2 <ide_input_data+34>: je 0xc0208fb0
<ide_input_data+48>
0xc0208fa4 <ide_input_data+36>: push %ebx
0xc0208fa5 <ide_input_data+37>: push %edi
0xc0208fa6 <ide_input_data+38>: push %esi
0xc0208fa7 <ide_input_data+39>: push $0x0
0xc0208fa9 <ide_input_data+41>: call *%eax
0xc0208fab <ide_input_data+43>: jmp 0xc020904a
<ide_input_data+202>
0xc0208fb0 <ide_input_data+48>: movzbl 0xd5(%esi),%eax
0xc0208fb7 <ide_input_data+55>: test %al,%al
0xc0208fb9 <ide_input_data+57>: je 0xc0208ff0
<ide_input_data+112>
0xc0208fbb <ide_input_data+59>: and $0x2,%eax
0xc0208fbe <ide_input_data+62>: je 0xc0208fe0
<ide_input_data+96>
0xc0208fc0 <ide_input_data+64>: pushf
0xc0208fc1 <ide_input_data+65>: popl 0xffffffe8(%ebp)
0xc0208fc4 <ide_input_data+68>: cli
0xc0208fc5 <ide_input_data+69>: mov 0xfc(%esi),%esi
0xc0208fcb <ide_input_data+75>: movzwl 0xc(%esi),%edx
0xc0208fcf <ide_input_data+79>: in (%dx),%al
0xc0208fd0 <ide_input_data+80>: in (%dx),%al
0xc0208fd1 <ide_input_data+81>: in (%dx),%al
0xc0208fd2 <ide_input_data+82>: movzwl 0x8(%esi),%edx
0xc0208fd6 <ide_input_data+86>: mov %ebx,%ecx
0xc0208fd8 <ide_input_data+88>: repz insl (%dx),%es:(%edi)
0xc0208fda <ide_input_data+90>: pushl 0xffffffe8(%ebp)
0xc0208fdd <ide_input_data+93>: popf
0xc0208fde <ide_input_data+94>: jmp 0xc020904a
<ide_input_data+202>
0xc0208fe0 <ide_input_data+96>: movzwl 0x8(%edx),%edx
0xc0208fe4 <ide_input_data+100>: mov %ebx,%ecx
0xc0208fe6 <ide_input_data+102>: repz insl (%dx),%es:(%edi)
0xc0208fe8 <ide_input_data+104>: jmp 0xc020904a
<ide_input_data+202>
0xc0208fea <ide_input_data+106>: lea 0x0(%esi),%esi
0xc0208ff0 <ide_input_data+112>: cmpb $0x0,0xba(%esi)
0xc0208ff7 <ide_input_data+119>: je 0xc0209040
<ide_input_data+192>
0xc0208ff9 <ide_input_data+121>: dec %ebx
0xc0208ffa <ide_input_data+122>: cmp $0xffffffff,%ebx
0xc0208ffd <ide_input_data+125>: je 0xc020904a
<ide_input_data+202>
0xc0208fff <ide_input_data+127>: jmp 0xc0209010
<ide_input_data+144>
0xc0209001 <ide_input_data+129>: mov 0xfc(%esi),%ecx
0xc0209007 <ide_input_data+135>: mov %esi,%esi
0xc0209009 <ide_input_data+137>: lea 0x0(%edi,1),%edi
0xc0209010 <ide_input_data+144>: movzwl 0x8(%ecx),%edx
0xc0209014 <ide_input_data+148>: in (%dx),%ax
0xc0209016 <ide_input_data+150>: out %al,$0x80
0xc0209018 <ide_input_data+152>: mov %ax,(%edi)
0xc020901b <ide_input_data+155>: add $0x2,%edi
0xc020901e <ide_input_data+158>: mov 0xfc(%esi),%eax
0xc0209024 <ide_input_data+164>: movzwl 0x8(%eax),%edx
0xc0209028 <ide_input_data+168>: in (%dx),%ax
0xc020902a <ide_input_data+170>: out %al,$0x80
0xc020902c <ide_input_data+172>: mov %ax,(%edi)
0xc020902f <ide_input_data+175>: dec %ebx
0xc0209030 <ide_input_data+176>: add $0x2,%edi
0xc0209033 <ide_input_data+179>: cmp $0xffffffff,%ebx
0xc0209036 <ide_input_data+182>: jne 0xc0209001
<ide_input_data+129>
0xc0209038 <ide_input_data+184>: jmp 0xc020904a
<ide_input_data+202>
0xc020903a <ide_input_data+186>: lea 0x0(%esi),%esi
0xc0209040 <ide_input_data+192>: movzwl 0x8(%edx),%edx
0xc0209044 <ide_input_data+196>: lea (%ebx,%ebx,1),%ecx
0xc0209047 <ide_input_data+199>: repz insw (%dx),%es:(%edi)
0xc020904a <ide_input_data+202>: lea 0xfffffff4(%ebp),%esp
0xc020904d <ide_input_data+205>: pop %ebx
0xc020904e <ide_input_data+206>: pop %esi
0xc020904f <ide_input_data+207>: pop %edi
0xc0209050 <ide_input_data+208>: pop %ebp
0xc0209051 <ide_input_data+209>: ret
End of assembler dump.
=========================================================
I was running TOP remotely at the time too...
1:44pm up 16 min, 4 users, load average: 2.10, 1.78, 1.02
53 processes: 50 sleeping, 3 running, 0 zombie, 0 stopped
CPU0 states: 56.0% user, 26.2% system, 55.1% nice, 16.4% idle
CPU1 states: 24.5% user, 30.3% system, 23.3% nice, 44.2% idle
Mem: 515348K av, 484460K used, 30888K free, 0K shrd,
22104K buff
Swap: 409616K av, 0K used, 409616K free
423944K cached
PID USER PRI NI SIZE RSS SHARE STAT %CPU %MEM TIME
COMMAND
[garbled due to disconnect] 0 2004 2004 824 R N 97.9 0.3
0:17 oggenc
5519 root 15 10 2608 2576 504 S N 7.5 0.4 0:01
cdparanoia
5520 root 9 0 4020 4020 3224 S 2.1 0.7 0:00
gaim
2967 root 9 0 848 848 560 D 1.5 0.1 0:11
mkisofs
2463 root 9 0 5160 5160 3084 R 1.1 1.0 0:03
xcdroast
2347 root 9 0 2336 2316 1700 S 0.9 0.4 0:01
sshd
3269 root 9 0 1040 1040 836 R 0.3 0.2 0:01
top
12 root 9 0 0 0 0 SW 0.1 0.0 0:00
kjournald
904 root 9 0 1804 1804 1296 S 0.1 0.3 0:00
cupsd
1 root 8 0 520 520 452 S 0.0 0.1 0:04
init
2 root 9 0 0 0 0 SW 0.0 0.0 0:00
keventd
3 root 18 19 0 0 0 SWN 0.0 0.0 0:00
ksoftirqd_CPU0
4 root 18 19 0 0 0 SWN 0.0 0.0 0:00
ksoftirqd_CPU1
5 root 9 0 0 0 0 SW 0.0 0.0 0:00
kswapd
6 root 9 0 0 0 0 SW 0.0 0.0 0:00
bdflush
=========================================================
Please let me know if you'd like me to reproduce it and follow
some procedure.
Thanks!
-bobzibub
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2002-12-19 23:01 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-12-19 23:05 PROBLEM: Oops during high ide io loads David A. Chappel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).