From: Konstantin <rilian.la.te@ya.ru>
Cc: Konstantin <ria.freelander@gmail.com>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Jiri Slaby" <jirislaby@kernel.org>,
"Hugo Villeneuve" <hvilleneuve@dimonoff.com>,
"Andy Shevchenko" <andriy.shevchenko@linux.intel.com>,
"Lech Perczak" <lech.perczak@camlingroup.com>,
"Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>,
"Thomas Gleixner" <tglx@linutronix.de>,
linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org
Subject: [PATCH 3/3] serial: sc16is7xx: add support for EXAR XR20M1172 UART
Date: Thu, 18 Apr 2024 16:25:05 +0300 [thread overview]
Message-ID: <20240418132508.3447800-4-rilian.la.te@ya.ru> (raw)
In-Reply-To: <20240418132508.3447800-1-rilian.la.te@ya.ru>
From: Konstantin <ria.freelander@gmail.com>
Its register set is mostly compatible with SC16IS762, but
it has a support for additional division rates of UART
with special DLD register. So, add handling this register
via UPF_MAGIC_MULTIPLIER port flag.
Signed-off-by: Konstantin Pugin <ria.freelander@gmail.com>
---
drivers/tty/serial/sc16is7xx.c | 54 ++++++++++++++++++++++++++++++++--
1 file changed, 51 insertions(+), 3 deletions(-)
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index a300eebf1401..7fc1c19b3891 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -65,6 +65,7 @@
/* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */
#define SC16IS7XX_DLL_REG (0x00) /* Divisor Latch Low */
#define SC16IS7XX_DLH_REG (0x01) /* Divisor Latch High */
+#define SC16IS7XX_DLD_REG (0x02) /* Divisor Latch Mode (only on EXAR chips) */
/* Enhanced Register set: Only if (LCR == 0xBF) */
#define SC16IS7XX_EFR_REG (0x02) /* Enhanced Features */
@@ -218,6 +219,20 @@
#define SC16IS7XX_TCR_RX_HALT(words) ((((words) / 4) & 0x0f) << 0)
#define SC16IS7XX_TCR_RX_RESUME(words) ((((words) / 4) & 0x0f) << 4)
+/* Divisor Latch Mode bits (EXAR extension)
+ *
+ * EXAR hardware is mostly compatible with SC16IS7XX, but supports additional feature:
+ * 4x and 8x divisor, instead of default 16x. It has a special register to program it.
+ * Bits 0 to 3 is fractional divisor, it used to set value of last 16 bits of
+ * uartclk * (16 / divisor) / baud, in case of default it will be uartclk / baud.
+ * Bits 4 and 5 used as switches, and should not be set to 1 simultaneously.
+ */
+
+#define SC16IS7XX_DLD_16X 0
+#define SC16IS7XX_DLD_DIV(m) ((m) & 0xf)
+#define SC16IS7XX_DLD_8X BIT(4)
+#define SC16IS7XX_DLD_4X BIT(5)
+
/*
* TLR register bits
* If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the
@@ -310,6 +325,7 @@ struct sc16is7xx_devtype {
char name[10];
int nr_gpio;
int nr_uart;
+ bool has_dld;
};
#define SC16IS7XX_RECONF_MD (1 << 0)
@@ -522,6 +538,13 @@ static const struct sc16is7xx_devtype sc16is762_devtype = {
.nr_uart = 2,
};
+static const struct sc16is7xx_devtype xr20m1172_devtype = {
+ .name = "XR20M1172",
+ .nr_gpio = 8,
+ .nr_uart = 2,
+ .has_dld = true,
+};
+
static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg)
{
switch (reg) {
@@ -559,13 +582,29 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
u8 lcr;
u8 prescaler = 0;
- unsigned long clk = port->uartclk, div = clk / 16 / baud;
+ u8 divisor = 16;
+ u8 dld_mode = SC16IS7XX_DLD_16X;
+ bool has_dld = !!(port->flags & UPF_MAGIC_MULTIPLIER);
+ unsigned long clk = port->uartclk, div, div16;
+
+ if (has_dld)
+ while (DIV_ROUND_CLOSEST(port->uartclk, baud) < divisor)
+ divisor /= 2;
+
+ div16 = clk * (16 / divisor) / baud;
+ div = div16 / 16; /* For divisor = 16, it is the same as clk / 16 / baud */
if (div >= BIT(16)) {
prescaler = SC16IS7XX_MCR_CLKSEL_BIT;
div /= 4;
}
+ /* Count additional divisor for EXAR devices */
+ if (divisor == 8)
+ dld_mode = SC16IS7XX_DLD_8X;
+ if (divisor == 4)
+ dld_mode = SC16IS7XX_DLD_4X;
+
/* Enable enhanced features */
sc16is7xx_efr_lock(port);
sc16is7xx_port_update(port, SC16IS7XX_EFR_REG,
@@ -586,12 +625,14 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
regcache_cache_bypass(one->regmap, true);
sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256);
sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256);
+ if (has_dld)
+ sc16is7xx_port_write(port, SC16IS7XX_DLD_REG, dld_mode | SC16IS7XX_DLD_DIV(div16));
regcache_cache_bypass(one->regmap, false);
/* Restore LCR and access to general register set */
sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);
- return DIV_ROUND_CLOSEST(clk / 16, div);
+ return DIV_ROUND_CLOSEST(clk / divisor, div);
}
static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen,
@@ -1014,6 +1055,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
unsigned int lcr, flow = 0;
int baud;
unsigned long flags;
+ bool has_dld = !!(port->flags & UPF_MAGIC_MULTIPLIER);
kthread_cancel_delayed_work_sync(&one->ms_work);
@@ -1093,7 +1135,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
/* Get baud rate generator configuration */
baud = uart_get_baud_rate(port, termios, old,
port->uartclk / 16 / 4 / 0xffff,
- port->uartclk / 16);
+ port->uartclk / (has_dld ? 4 : 16));
/* Setup baudrate generator */
baud = sc16is7xx_set_baud(port, baud);
@@ -1550,6 +1592,9 @@ static int sc16is7xx_probe(struct device *dev,
s->p[i].port.type = PORT_SC16IS7XX;
s->p[i].port.fifosize = SC16IS7XX_FIFO_SIZE;
s->p[i].port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY;
+ /* If we have DLD register, then set UPF_MAGIC_MULTIPLIER flag */
+ if (devtype->has_dld)
+ s->p[i].port.flags |= UPF_MAGIC_MULTIPLIER;
s->p[i].port.iobase = i;
/*
* Use all ones as membase to make sure uart_configure_port() in
@@ -1688,6 +1733,7 @@ static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = {
{ .compatible = "nxp,sc16is752", .data = &sc16is752_devtype, },
{ .compatible = "nxp,sc16is760", .data = &sc16is760_devtype, },
{ .compatible = "nxp,sc16is762", .data = &sc16is762_devtype, },
+ { .compatible = "exar,xr20m1172", .data = &xr20m1172_devtype, },
{ }
};
MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids);
@@ -1776,6 +1822,7 @@ static const struct spi_device_id sc16is7xx_spi_id_table[] = {
{ "sc16is752", (kernel_ulong_t)&sc16is752_devtype, },
{ "sc16is760", (kernel_ulong_t)&sc16is760_devtype, },
{ "sc16is762", (kernel_ulong_t)&sc16is762_devtype, },
+ { "xr20m1172", (kernel_ulong_t)&xr20m1172_devtype, },
{ }
};
@@ -1826,6 +1873,7 @@ static const struct i2c_device_id sc16is7xx_i2c_id_table[] = {
{ "sc16is752", (kernel_ulong_t)&sc16is752_devtype, },
{ "sc16is760", (kernel_ulong_t)&sc16is760_devtype, },
{ "sc16is762", (kernel_ulong_t)&sc16is762_devtype, },
+ { "xr20m1172", (kernel_ulong_t)&xr20m1172_devtype, },
{ }
};
MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table);
--
2.34.1
next prev parent reply other threads:[~2024-04-18 13:25 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-04-18 13:25 [PATCH 0/3] add support for EXAR XR20M1172 UART Konstantin
2024-04-18 13:25 ` [PATCH 1/3] serial: sc16is7xx: announce support of SER_RS485_RTS_ON_SEND Konstantin
2024-04-18 13:25 ` [PATCH 2/3] serial: sc16is7xx: Add bindings documentation for EXAR XR20M1172 UART Konstantin
2024-04-18 13:47 ` Vladimir Zapolskiy
2024-04-18 13:25 ` Konstantin [this message]
2024-04-19 5:45 ` [PATCH 3/3] serial: sc16is7xx: add support " Jiri Slaby
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240418132508.3447800-4-rilian.la.te@ya.ru \
--to=rilian.la.te@ya.ru \
--cc=andriy.shevchenko@linux.intel.com \
--cc=gregkh@linuxfoundation.org \
--cc=hvilleneuve@dimonoff.com \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=jirislaby@kernel.org \
--cc=lech.perczak@camlingroup.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=ria.freelander@gmail.com \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).