From: Manuel Traut <manut@mecka.net>
To: Jens Wiklander <jens.wiklander@linaro.org>
Cc: linux-kernel@vger.kernel.org, linux-mmc@vger.kernel.org,
op-tee@lists.trustedfirmware.org,
Shyam Saini <shyamsaini@linux.microsoft.com>,
Ulf Hansson <ulf.hansson@linaro.org>,
Linus Walleij <linus.walleij@linaro.org>,
Jerome Forissier <jerome.forissier@linaro.org>,
Sumit Garg <sumit.garg@linaro.org>,
Ilias Apalodimas <ilias.apalodimas@linaro.org>,
Bart Van Assche <bvanassche@acm.org>,
Randy Dunlap <rdunlap@infradead.org>,
Ard Biesheuvel <ardb@kernel.org>, Arnd Bergmann <arnd@arndb.de>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subject: Re: [PATCH v6 3/3] optee: probe RPMB device using RPMB subsystem
Date: Tue, 14 May 2024 15:29:10 +0000 [thread overview]
Message-ID: <ZkODRk7Us-9MlyYb@mecka.net> (raw)
In-Reply-To: <20240507091619.2208810-4-jens.wiklander@linaro.org>
On Tue, May 07, 2024 at 11:16:19AM +0200, Jens Wiklander wrote:
> Adds support in the OP-TEE drivers (both SMC and FF-A ABIs) to probe and
> use an RPMB device via the RPMB subsystem instead of passing the RPMB
> frames via tee-supplicant in user space. A fallback mechanism is kept to
> route RPMB frames via tee-supplicant if the RPMB subsystem isn't
> available.
>
> The OP-TEE RPC ABI is extended to support iterating over all RPMB
> devices until one is found with the expected RPMB key already
> programmed.
>
> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Tested-by: Manuel Traut <manut@mecka.net>
> ---
> drivers/tee/optee/core.c | 30 ++++++
> drivers/tee/optee/device.c | 7 ++
> drivers/tee/optee/ffa_abi.c | 8 ++
> drivers/tee/optee/optee_private.h | 21 +++-
> drivers/tee/optee/optee_rpc_cmd.h | 35 +++++++
> drivers/tee/optee/rpc.c | 166 ++++++++++++++++++++++++++++++
> drivers/tee/optee/smc_abi.c | 7 ++
> 7 files changed, 273 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/tee/optee/core.c b/drivers/tee/optee/core.c
> index 3aed554bc8d8..082691c10a90 100644
> --- a/drivers/tee/optee/core.c
> +++ b/drivers/tee/optee/core.c
> @@ -11,6 +11,7 @@
> #include <linux/io.h>
> #include <linux/mm.h>
> #include <linux/module.h>
> +#include <linux/rpmb.h>
> #include <linux/slab.h>
> #include <linux/string.h>
> #include <linux/tee_drv.h>
> @@ -80,6 +81,31 @@ void optee_pool_op_free_helper(struct tee_shm_pool *pool, struct tee_shm *shm,
> shm->pages = NULL;
> }
>
> +void optee_bus_scan_rpmb(struct work_struct *work)
> +{
> + struct optee *optee = container_of(work, struct optee,
> + rpmb_scan_bus_work);
> + int ret;
> +
> + if (!optee->rpmb_scan_bus_done) {
> + ret = optee_enumerate_devices(PTA_CMD_GET_DEVICES_RPMB);
> + optee->rpmb_scan_bus_done = !ret;
> + if (ret && ret != -ENODEV)
> + pr_info("Scanning for RPMB device: ret %d\n", ret);
> + }
> +}
> +
> +int optee_rpmb_intf_rdev(struct notifier_block *intf, unsigned long action,
> + void *data)
> +{
> + struct optee *optee = container_of(intf, struct optee, rpmb_intf);
> +
> + if (action == RPMB_NOTIFY_ADD_DEVICE)
> + schedule_work(&optee->rpmb_scan_bus_work);
> +
> + return 0;
> +}
> +
> static void optee_bus_scan(struct work_struct *work)
> {
> WARN_ON(optee_enumerate_devices(PTA_CMD_GET_DEVICES_SUPP));
> @@ -161,6 +187,8 @@ void optee_release_supp(struct tee_context *ctx)
>
> void optee_remove_common(struct optee *optee)
> {
> + rpmb_interface_unregister(&optee->rpmb_intf);
> + cancel_work_sync(&optee->rpmb_scan_bus_work);
> /* Unregister OP-TEE specific client devices on TEE bus */
> optee_unregister_devices();
>
> @@ -177,6 +205,8 @@ void optee_remove_common(struct optee *optee)
> tee_shm_pool_free(optee->pool);
> optee_supp_uninit(&optee->supp);
> mutex_destroy(&optee->call_queue.mutex);
> + rpmb_dev_put(optee->rpmb_dev);
> + mutex_destroy(&optee->rpmb_dev_mutex);
> }
>
> static int smc_abi_rc;
> diff --git a/drivers/tee/optee/device.c b/drivers/tee/optee/device.c
> index 4b1092127694..4274876857c8 100644
> --- a/drivers/tee/optee/device.c
> +++ b/drivers/tee/optee/device.c
> @@ -43,6 +43,13 @@ static int get_devices(struct tee_context *ctx, u32 session,
> ret = tee_client_invoke_func(ctx, &inv_arg, param);
> if ((ret < 0) || ((inv_arg.ret != TEEC_SUCCESS) &&
> (inv_arg.ret != TEEC_ERROR_SHORT_BUFFER))) {
> + /*
> + * TEE_ERROR_STORAGE_NOT_AVAILABLE is returned when getting
> + * the list of device TAs that depends on RPMB but a usable
> + * RPMB device isn't found.
> + */
> + if (inv_arg.ret == TEE_ERROR_STORAGE_NOT_AVAILABLE)
> + return -ENODEV;
> pr_err("PTA_CMD_GET_DEVICES invoke function err: %x\n",
> inv_arg.ret);
> return -EINVAL;
> diff --git a/drivers/tee/optee/ffa_abi.c b/drivers/tee/optee/ffa_abi.c
> index ecb5eb079408..a8dfdb30b4e8 100644
> --- a/drivers/tee/optee/ffa_abi.c
> +++ b/drivers/tee/optee/ffa_abi.c
> @@ -7,6 +7,7 @@
>
> #include <linux/arm_ffa.h>
> #include <linux/errno.h>
> +#include <linux/rpmb.h>
> #include <linux/scatterlist.h>
> #include <linux/sched.h>
> #include <linux/slab.h>
> @@ -934,6 +935,7 @@ static int optee_ffa_probe(struct ffa_device *ffa_dev)
> optee_cq_init(&optee->call_queue, 0);
> optee_supp_init(&optee->supp);
> optee_shm_arg_cache_init(optee, arg_cache_flags);
> + mutex_init(&optee->rpmb_dev_mutex);
> ffa_dev_set_drvdata(ffa_dev, optee);
> ctx = teedev_open(optee->teedev);
> if (IS_ERR(ctx)) {
> @@ -955,6 +957,9 @@ static int optee_ffa_probe(struct ffa_device *ffa_dev)
> if (rc)
> goto err_unregister_devices;
>
> + INIT_WORK(&optee->rpmb_scan_bus_work, optee_bus_scan_rpmb);
> + optee->rpmb_intf.notifier_call = optee_rpmb_intf_rdev;
> + rpmb_interface_register(&optee->rpmb_intf);
> pr_info("initialized driver\n");
> return 0;
>
> @@ -968,6 +973,9 @@ static int optee_ffa_probe(struct ffa_device *ffa_dev)
> teedev_close_context(ctx);
> err_rhashtable_free:
> rhashtable_free_and_destroy(&optee->ffa.global_ids, rh_free_fn, NULL);
> + rpmb_dev_put(optee->rpmb_dev);
> + mutex_destroy(&optee->rpmb_dev_mutex);
> + rpmb_interface_unregister(&optee->rpmb_intf);
> optee_supp_uninit(&optee->supp);
> mutex_destroy(&optee->call_queue.mutex);
> mutex_destroy(&optee->ffa.mutex);
> diff --git a/drivers/tee/optee/optee_private.h b/drivers/tee/optee/optee_private.h
> index 7a5243c78b55..ae72f3dda1d2 100644
> --- a/drivers/tee/optee/optee_private.h
> +++ b/drivers/tee/optee/optee_private.h
> @@ -8,6 +8,7 @@
>
> #include <linux/arm-smccc.h>
> #include <linux/rhashtable.h>
> +#include <linux/rpmb.h>
> #include <linux/semaphore.h>
> #include <linux/tee_drv.h>
> #include <linux/types.h>
> @@ -20,11 +21,13 @@
> /* Some Global Platform error codes used in this driver */
> #define TEEC_SUCCESS 0x00000000
> #define TEEC_ERROR_BAD_PARAMETERS 0xFFFF0006
> +#define TEEC_ERROR_ITEM_NOT_FOUND 0xFFFF0008
> #define TEEC_ERROR_NOT_SUPPORTED 0xFFFF000A
> #define TEEC_ERROR_COMMUNICATION 0xFFFF000E
> #define TEEC_ERROR_OUT_OF_MEMORY 0xFFFF000C
> #define TEEC_ERROR_BUSY 0xFFFF000D
> #define TEEC_ERROR_SHORT_BUFFER 0xFFFF0010
> +#define TEE_ERROR_STORAGE_NOT_AVAILABLE 0xF0100003
>
> #define TEEC_ORIGIN_COMMS 0x00000002
>
> @@ -197,6 +200,12 @@ struct optee_ops {
> * @notif: notification synchronization struct
> * @supp: supplicant synchronization struct for RPC to supplicant
> * @pool: shared memory pool
> + * @mutex: mutex protecting @rpmb_dev
> + * @rpmb_dev: current RPMB device or NULL
> + * @rpmb_scan_bus_done flag if device registation of RPMB dependent devices
> + * was already done
> + * @rpmb_scan_bus_work workq to for an RPMB device and to scan optee bus
> + * and register RPMB dependent optee drivers
> * @rpc_param_count: If > 0 number of RPC parameters to make room for
> * @scan_bus_done flag if device registation was already done.
> * @scan_bus_work workq to scan optee bus and register optee drivers
> @@ -215,9 +224,15 @@ struct optee {
> struct optee_notif notif;
> struct optee_supp supp;
> struct tee_shm_pool *pool;
> + /* Protects rpmb_dev pointer */
> + struct mutex rpmb_dev_mutex;
> + struct rpmb_dev *rpmb_dev;
> + struct notifier_block rpmb_intf;
> unsigned int rpc_param_count;
> - bool scan_bus_done;
> + bool scan_bus_done;
> + bool rpmb_scan_bus_done;
> struct work_struct scan_bus_work;
> + struct work_struct rpmb_scan_bus_work;
> };
>
> struct optee_session {
> @@ -280,8 +295,12 @@ int optee_cancel_req(struct tee_context *ctx, u32 cancel_id, u32 session);
>
> #define PTA_CMD_GET_DEVICES 0x0
> #define PTA_CMD_GET_DEVICES_SUPP 0x1
> +#define PTA_CMD_GET_DEVICES_RPMB 0x2
> int optee_enumerate_devices(u32 func);
> void optee_unregister_devices(void);
> +void optee_bus_scan_rpmb(struct work_struct *work);
> +int optee_rpmb_intf_rdev(struct notifier_block *intf, unsigned long action,
> + void *data);
>
> int optee_pool_op_alloc_helper(struct tee_shm_pool *pool, struct tee_shm *shm,
> size_t size, size_t align,
> diff --git a/drivers/tee/optee/optee_rpc_cmd.h b/drivers/tee/optee/optee_rpc_cmd.h
> index f3f06e0994a7..4a3c02914f9c 100644
> --- a/drivers/tee/optee/optee_rpc_cmd.h
> +++ b/drivers/tee/optee/optee_rpc_cmd.h
> @@ -103,4 +103,39 @@
> /* I2C master control flags */
> #define OPTEE_RPC_I2C_FLAGS_TEN_BIT BIT(0)
>
> +/*
> + * Reset RPMB probing
> + *
> + * Releases an eventually already used RPMB devices and starts over searching
> + * for RPMB devices. Returns the kind of shared memory to use in subsequent
> + * OPTEE_RPC_CMD_RPMB_PROBE_NEXT and OPTEE_RPC_CMD_RPMB calls.
> + *
> + * [out] value[0].a OPTEE_RPC_SHM_TYPE_*, the parameter for
> + * OPTEE_RPC_CMD_SHM_ALLOC
> + */
> +#define OPTEE_RPC_CMD_RPMB_PROBE_RESET 22
> +
> +/*
> + * Probe next RPMB device
> + *
> + * [out] value[0].a Type of RPMB device, OPTEE_RPC_RPMB_*
> + * [out] value[0].b EXT CSD-slice 168 "RPMB Size"
> + * [out] value[0].c EXT CSD-slice 222 "Reliable Write Sector Count"
> + * [out] memref[1] Buffer with the raw CID
> + */
> +#define OPTEE_RPC_CMD_RPMB_PROBE_NEXT 23
> +
> +/* Type of RPMB device */
> +#define OPTEE_RPC_RPMB_EMMC 0
> +#define OPTEE_RPC_RPMB_UFS 1
> +#define OPTEE_RPC_RPMB_NVME 2
> +
> +/*
> + * Replay Protected Memory Block access
> + *
> + * [in] memref[0] Frames to device
> + * [out] memref[1] Frames from device
> + */
> +#define OPTEE_RPC_CMD_RPMB_FRAMES 24
> +
> #endif /*__OPTEE_RPC_CMD_H*/
> diff --git a/drivers/tee/optee/rpc.c b/drivers/tee/optee/rpc.c
> index e69bc6380683..f3acb4240fcb 100644
> --- a/drivers/tee/optee/rpc.c
> +++ b/drivers/tee/optee/rpc.c
> @@ -7,6 +7,7 @@
>
> #include <linux/delay.h>
> #include <linux/i2c.h>
> +#include <linux/rpmb.h>
> #include <linux/slab.h>
> #include <linux/tee_drv.h>
> #include "optee_private.h"
> @@ -255,6 +256,162 @@ void optee_rpc_cmd_free_suppl(struct tee_context *ctx, struct tee_shm *shm)
> optee_supp_thrd_req(ctx, OPTEE_RPC_CMD_SHM_FREE, 1, ¶m);
> }
>
> +static void handle_rpc_func_rpmb_probe_reset(struct tee_context *ctx,
> + struct optee *optee,
> + struct optee_msg_arg *arg)
> +{
> + struct tee_param params[1];
> +
> + if (!IS_ENABLED(CONFIG_RPMB)) {
> + handle_rpc_supp_cmd(ctx, optee, arg);
> + return;
> + }
> +
> + if (arg->num_params != ARRAY_SIZE(params) ||
> + optee->ops->from_msg_param(optee, params, arg->num_params,
> + arg->params) ||
> + params[0].attr != TEE_IOCTL_PARAM_ATTR_TYPE_VALUE_OUTPUT) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + return;
> + }
> +
> + params[0].u.value.a = OPTEE_RPC_SHM_TYPE_KERNEL;
> + params[0].u.value.b = 0;
> + params[0].u.value.c = 0;
> + if (optee->ops->to_msg_param(optee, arg->params,
> + arg->num_params, params)) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + return;
> + }
> +
> + mutex_lock(&optee->rpmb_dev_mutex);
> + rpmb_dev_put(optee->rpmb_dev);
> + optee->rpmb_dev = NULL;
> + mutex_unlock(&optee->rpmb_dev_mutex);
> +
> + arg->ret = TEEC_SUCCESS;
> +}
> +
> +static int rpmb_type_to_rpc_type(enum rpmb_type rtype)
> +{
> + switch (rtype) {
> + case RPMB_TYPE_EMMC:
> + return OPTEE_RPC_RPMB_EMMC;
> + case RPMB_TYPE_UFS:
> + return OPTEE_RPC_RPMB_UFS;
> + case RPMB_TYPE_NVME:
> + return OPTEE_RPC_RPMB_NVME;
> + default:
> + return -1;
> + }
> +}
> +
> +static int rpc_rpmb_match(struct rpmb_dev *rdev, const void *data)
> +{
> + return rpmb_type_to_rpc_type(rdev->descr.type) >= 0;
> +}
> +
> +static void handle_rpc_func_rpmb_probe_next(struct tee_context *ctx,
> + struct optee *optee,
> + struct optee_msg_arg *arg)
> +{
> + struct rpmb_dev *rdev;
> + struct tee_param params[2];
> + void *buf;
> +
> + if (!IS_REACHABLE(CONFIG_RPMB)) {
> + handle_rpc_supp_cmd(ctx, optee, arg);
> + return;
> + }
> +
> + if (arg->num_params != ARRAY_SIZE(params) ||
> + optee->ops->from_msg_param(optee, params, arg->num_params,
> + arg->params) ||
> + params[0].attr != TEE_IOCTL_PARAM_ATTR_TYPE_VALUE_OUTPUT ||
> + params[1].attr != TEE_IOCTL_PARAM_ATTR_TYPE_MEMREF_OUTPUT) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + return;
> + }
> + buf = tee_shm_get_va(params[1].u.memref.shm,
> + params[1].u.memref.shm_offs);
> + if (!buf) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + return;
> + }
> +
> + mutex_lock(&optee->rpmb_dev_mutex);
> + rdev = rpmb_dev_find_device(NULL, optee->rpmb_dev, rpc_rpmb_match);
> + rpmb_dev_put(optee->rpmb_dev);
> + optee->rpmb_dev = rdev;
> + mutex_unlock(&optee->rpmb_dev_mutex);
> +
> + if (!rdev) {
> + arg->ret = TEEC_ERROR_ITEM_NOT_FOUND;
> + return;
> + }
> +
> + if (params[1].u.memref.size < rdev->descr.dev_id_len) {
> + arg->ret = TEEC_ERROR_SHORT_BUFFER;
> + return;
> + }
> + memcpy(buf, rdev->descr.dev_id, rdev->descr.dev_id_len);
> + params[1].u.memref.size = rdev->descr.dev_id_len;
> + params[0].u.value.a = rpmb_type_to_rpc_type(rdev->descr.type);
> + params[0].u.value.b = rdev->descr.capacity;
> + params[0].u.value.c = rdev->descr.reliable_wr_count;
> + if (optee->ops->to_msg_param(optee, arg->params,
> + arg->num_params, params)) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + return;
> + }
> +
> + arg->ret = TEEC_SUCCESS;
> +}
> +
> +static void handle_rpc_func_rpmb_frames(struct tee_context *ctx,
> + struct optee *optee,
> + struct optee_msg_arg *arg)
> +{
> + struct tee_param params[2];
> + struct rpmb_dev *rdev;
> + void *p0, *p1;
> +
> + mutex_lock(&optee->rpmb_dev_mutex);
> + rdev = rpmb_dev_get(optee->rpmb_dev);
> + mutex_unlock(&optee->rpmb_dev_mutex);
> + if (!rdev) {
> + handle_rpc_supp_cmd(ctx, optee, arg);
> + return;
> + }
> +
> + if (arg->num_params != ARRAY_SIZE(params) ||
> + optee->ops->from_msg_param(optee, params, arg->num_params,
> + arg->params) ||
> + params[0].attr != TEE_IOCTL_PARAM_ATTR_TYPE_MEMREF_INPUT ||
> + params[1].attr != TEE_IOCTL_PARAM_ATTR_TYPE_MEMREF_OUTPUT) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + goto out;
> + }
> +
> + p0 = tee_shm_get_va(params[0].u.memref.shm,
> + params[0].u.memref.shm_offs);
> + p1 = tee_shm_get_va(params[1].u.memref.shm,
> + params[1].u.memref.shm_offs);
> + if (rpmb_route_frames(rdev, p0, params[0].u.memref.size, p1,
> + params[1].u.memref.size)) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + goto out;
> + }
> + if (optee->ops->to_msg_param(optee, arg->params,
> + arg->num_params, params)) {
> + arg->ret = TEEC_ERROR_BAD_PARAMETERS;
> + goto out;
> + }
> + arg->ret = TEEC_SUCCESS;
> +out:
> + rpmb_dev_put(rdev);
> +}
> +
> void optee_rpc_cmd(struct tee_context *ctx, struct optee *optee,
> struct optee_msg_arg *arg)
> {
> @@ -271,6 +428,15 @@ void optee_rpc_cmd(struct tee_context *ctx, struct optee *optee,
> case OPTEE_RPC_CMD_I2C_TRANSFER:
> handle_rpc_func_cmd_i2c_transfer(ctx, arg);
> break;
> + case OPTEE_RPC_CMD_RPMB_PROBE_RESET:
> + handle_rpc_func_rpmb_probe_reset(ctx, optee, arg);
> + break;
> + case OPTEE_RPC_CMD_RPMB_PROBE_NEXT:
> + handle_rpc_func_rpmb_probe_next(ctx, optee, arg);
> + break;
> + case OPTEE_RPC_CMD_RPMB_FRAMES:
> + handle_rpc_func_rpmb_frames(ctx, optee, arg);
> + break;
> default:
> handle_rpc_supp_cmd(ctx, optee, arg);
> }
> diff --git a/drivers/tee/optee/smc_abi.c b/drivers/tee/optee/smc_abi.c
> index a37f87087e5c..c23bcf35c8cb 100644
> --- a/drivers/tee/optee/smc_abi.c
> +++ b/drivers/tee/optee/smc_abi.c
> @@ -20,6 +20,7 @@
> #include <linux/of_irq.h>
> #include <linux/of_platform.h>
> #include <linux/platform_device.h>
> +#include <linux/rpmb.h>
> #include <linux/sched.h>
> #include <linux/slab.h>
> #include <linux/string.h>
> @@ -1715,6 +1716,7 @@ static int optee_probe(struct platform_device *pdev)
> optee->smc.memremaped_shm = memremaped_shm;
> optee->pool = pool;
> optee_shm_arg_cache_init(optee, arg_cache_flags);
> + mutex_init(&optee->rpmb_dev_mutex);
>
> platform_set_drvdata(pdev, optee);
> ctx = teedev_open(optee->teedev);
> @@ -1769,6 +1771,9 @@ static int optee_probe(struct platform_device *pdev)
> if (rc)
> goto err_disable_shm_cache;
>
> + INIT_WORK(&optee->rpmb_scan_bus_work, optee_bus_scan_rpmb);
> + optee->rpmb_intf.notifier_call = optee_rpmb_intf_rdev;
> + rpmb_interface_register(&optee->rpmb_intf);
> pr_info("initialized driver\n");
> return 0;
>
> @@ -1782,6 +1787,8 @@ static int optee_probe(struct platform_device *pdev)
> err_close_ctx:
> teedev_close_context(ctx);
> err_supp_uninit:
> + rpmb_dev_put(optee->rpmb_dev);
> + mutex_destroy(&optee->rpmb_dev_mutex);
> optee_shm_arg_cache_uninit(optee);
> optee_supp_uninit(&optee->supp);
> mutex_destroy(&optee->call_queue.mutex);
> --
> 2.34.1
>
next prev parent reply other threads:[~2024-05-14 15:29 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-05-07 9:16 [PATCH v6 0/3] Replay Protected Memory Block (RPMB) subsystem Jens Wiklander
2024-05-07 9:16 ` [PATCH v6 1/3] rpmb: add " Jens Wiklander
2024-05-14 15:28 ` Manuel Traut
2024-05-14 15:45 ` Greg Kroah-Hartman
2024-05-15 7:51 ` Jens Wiklander
2024-05-15 8:04 ` Greg Kroah-Hartman
2024-05-15 9:45 ` Jens Wiklander
2024-05-07 9:16 ` [PATCH v6 2/3] mmc: block: register RPMB partition with the RPMB subsystem Jens Wiklander
2024-05-14 15:28 ` Manuel Traut
2024-05-07 9:16 ` [PATCH v6 3/3] optee: probe RPMB device using " Jens Wiklander
2024-05-14 15:29 ` Manuel Traut [this message]
2024-05-14 15:28 ` [PATCH v6 0/3] Replay Protected Memory Block (RPMB) subsystem Manuel Traut
2024-05-22 15:33 ` Jens Wiklander
2024-05-23 8:34 ` Manuel Traut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ZkODRk7Us-9MlyYb@mecka.net \
--to=manut@mecka.net \
--cc=ardb@kernel.org \
--cc=arnd@arndb.de \
--cc=bvanassche@acm.org \
--cc=gregkh@linuxfoundation.org \
--cc=ilias.apalodimas@linaro.org \
--cc=jens.wiklander@linaro.org \
--cc=jerome.forissier@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=op-tee@lists.trustedfirmware.org \
--cc=rdunlap@infradead.org \
--cc=shyamsaini@linux.microsoft.com \
--cc=sumit.garg@linaro.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).