From: "Théo Lebrun" <theo.lebrun@bootlin.com>
To: Linus Walleij <linus.walleij@linaro.org>,
Andi Shyti <andi.shyti@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-arm-kernel@lists.infradead.org, linux-i2c@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-mips@vger.kernel.org,
"Gregory Clement" <gregory.clement@bootlin.com>,
"Vladimir Kondratiev" <vladimir.kondratiev@mobileye.com>,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
"Tawfik Bayouk" <tawfik.bayouk@mobileye.com>,
"Théo Lebrun" <theo.lebrun@bootlin.com>,
"Wolfram Sang" <wsa+renesas@sang-engineering.com>
Subject: [PATCH v3 00/11] Add Mobileye EyeQ5 support to the Nomadik I2C controller & use hrtimers for timeouts
Date: Wed, 06 Mar 2024 18:59:20 +0100 [thread overview]
Message-ID: <20240306-mbly-i2c-v3-0-605f866aa4ec@bootlin.com> (raw)
Hi,
This series adds two tangent features to the Nomadik I2C controller:
- Add a new compatible to support Mobileye EyeQ5 which uses the same IP
block as Nomadik.
It has two quirks to be handled:
- The memory bus only supports 32-bit accesses. Avoid readb() and
writeb() calls that might generate byte load/store instructions.
- We must write a value into a shared register region (OLB)
depending on the I2C bus speed.
- Allow xfer timeouts below one jiffy by using a waitqueue and hrtimers
instead of a completion.
The situation to be addressed is:
- Many devices on the same I2C bus.
- One xfer to each device is sent at regular interval.
- One device gets stuck and does not answer.
- With long timeouts, following devices won't get their message. A
shorter timeout ensures we can still talk to the following
devices.
This clashes a bit with the current i2c_adapter timeout field that
stores a jiffies amount. We therefore avoid it and store the value
in a private struct field, as a µs amount. If the timeout is less
than a jiffy duration, we switch from standard jiffies timeout to
hrtimers.
About dependencies:
- For testing on EyeQ5 hardware and devicetree patches, we need the
base platform series from Grégory [0] and its dependency [1]. Both
in mips-next [2].
- Devicetree commits require the EyeQ5 syscon series [3] that provides
the reset controller node.
Have a nice day,
Théo Lebrun
[0]: https://lore.kernel.org/lkml/20240216174227.409400-1-gregory.clement@bootlin.com/
[1]: https://lore.kernel.org/linux-mips/20240209-regname-v1-0-2125efa016ef@flygoat.com/
[2]: https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/log/
[3]: https://lore.kernel.org/lkml/20240301-mbly-clk-v9-0-cbf06eb88708@bootlin.com/
To: Linus Walleij <linus.walleij@linaro.org>
To: Andi Shyti <andi.shyti@kernel.org>
To: Rob Herring <robh+dt@kernel.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <linux-i2c@vger.kernel.org>
Cc: <devicetree@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Vladimir Kondratiev <vladimir.kondratiev@mobileye.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Tawfik Bayouk <tawfik.bayouk@mobileye.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Changes in v3:
- dt-bindings:
- hwmon: lm75: drop patch taken into hwmon-next.
- i2c: nomadik: remove superfluous "The variant found in..." comments.
- i2c: nomadik:
- Add style fixes description in commit message of "rename private
struct pointers from dev to priv".
- Improve commit message of "simplify IRQ masking logic".
- introduce ADR_3MSB_BITS constant to avoid magic GENMASK() in code.
- Introduce enum i2c_operating_mode to avoid magic 0b01 in
DEFAULT_I2C_REG_CR. Named as in manual, using outdated terms.
- i2c_irq_handler(): add newline and split declaration and assignment
in I2C_IT_BERR case.
- Make timeout_usecs an u32 rather than int; avoid superfluous cast.
- nmk_i2c_probe(): remove extraneous debug log.
- nmk_i2c_eyeq5_probe():
- Straight return error and remove useless handling of NULL. Put
dev_err_probe() call in probe().
- Add ID value check.
- Add enum for speed mode values.
- Add static array for masks.
- Reorder includes in separate commit from Mobileye support.
- Take trailers from Andi, Wolfram and Linus.
- Link to v2: https://lore.kernel.org/r/20240229-mbly-i2c-v2-0-b32ed18c098c@bootlin.com
Changes in v2:
- dt-bindings: i2c: st,nomadic-i2c:
- Drop timeout-usecs property, rely on generic i2c-transfer-timeout-us.
- Use phandle to syscon with cell args; remove mobileye,id prop; move
mobileye,olb from if-statement to top-level.
- dt-bindings: hwmon: lm75:
- Inherit from hwmon-common.yaml rather than declare generic label property.
- i2c: nomadik: (ie driver code)
- Parse i2c-transfer-timeout-us rather than custom timeout-usecs property.
- Introduce readb/writeb helpers with fallback to readl/writel.
- Avoid readb() on Mobileye.
- Use mobileye,olb cell args to get controller index rather than mobileye,id.
- Take 5 Reviewed-by Linus Walleij.
- MIPS: mobileye: (ie devicetrees)
- Use mobileye,olb with cell args rather than mobileye,id.
- Squash reset commit.
- Add i2c-transfer-timeout-us value of 10ms to all controllers.
- Rename LM75 instance from tmp112@48 to temperature-sensor@48.
- Link to v1: https://lore.kernel.org/r/20240215-mbly-i2c-v1-0-19a336e91dca@bootlin.com
---
Théo Lebrun (11):
dt-bindings: i2c: nomadik: add mobileye,eyeq5-i2c bindings and example
i2c: nomadik: rename private struct pointers from dev to priv
i2c: nomadik: simplify IRQ masking logic
i2c: nomadik: use bitops helpers
i2c: nomadik: support short xfer timeouts using waitqueue & hrtimer
i2c: nomadik: replace jiffies by ktime for FIFO flushing timeout
i2c: nomadik: fetch i2c-transfer-timeout-us property from devicetree
i2c: nomadik: support Mobileye EyeQ5 I2C controller
i2c: nomadik: sort includes
MIPS: mobileye: eyeq5: add 5 I2C controller nodes
MIPS: mobileye: eyeq5: add evaluation board I2C temp sensor
.../devicetree/bindings/i2c/st,nomadik-i2c.yaml | 49 +-
arch/mips/boot/dts/mobileye/eyeq5-epm5.dts | 8 +
arch/mips/boot/dts/mobileye/eyeq5.dtsi | 75 +++
drivers/i2c/busses/i2c-nomadik.c | 740 ++++++++++++---------
4 files changed, 558 insertions(+), 314 deletions(-)
---
base-commit: 70a29ee8ef53a09ab62b46540c12ccb94a4a8532
change-id: 20231023-mbly-i2c-7c2fbbb1299f
Best regards,
--
Théo Lebrun <theo.lebrun@bootlin.com>
next reply other threads:[~2024-03-06 17:59 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-03-06 17:59 Théo Lebrun [this message]
2024-03-06 17:59 ` [PATCH v3 01/11] dt-bindings: i2c: nomadik: add mobileye,eyeq5-i2c bindings and example Théo Lebrun
2024-03-06 19:36 ` Rob Herring
2024-03-06 20:17 ` Rob Herring
2024-03-06 17:59 ` [PATCH v3 02/11] i2c: nomadik: rename private struct pointers from dev to priv Théo Lebrun
2024-03-06 17:59 ` [PATCH v3 03/11] i2c: nomadik: simplify IRQ masking logic Théo Lebrun
2024-03-07 23:01 ` Andi Shyti
2024-03-08 8:57 ` Théo Lebrun
2024-03-08 12:27 ` Andi Shyti
2024-03-08 13:33 ` Théo Lebrun
2024-03-06 17:59 ` [PATCH v3 04/11] i2c: nomadik: use bitops helpers Théo Lebrun
2024-03-07 23:04 ` Andi Shyti
2024-03-06 17:59 ` [PATCH v3 05/11] i2c: nomadik: support short xfer timeouts using waitqueue & hrtimer Théo Lebrun
2024-03-06 17:59 ` [PATCH v3 06/11] i2c: nomadik: replace jiffies by ktime for FIFO flushing timeout Théo Lebrun
2024-03-06 17:59 ` [PATCH v3 07/11] i2c: nomadik: fetch i2c-transfer-timeout-us property from devicetree Théo Lebrun
2024-03-06 17:59 ` [PATCH v3 08/11] i2c: nomadik: support Mobileye EyeQ5 I2C controller Théo Lebrun
2024-03-07 23:11 ` Andi Shyti
2024-03-08 9:16 ` Théo Lebrun
2024-03-08 12:28 ` Andi Shyti
2024-03-08 22:54 ` Andi Shyti
2024-03-11 8:59 ` Théo Lebrun
2024-03-06 17:59 ` [PATCH v3 09/11] i2c: nomadik: sort includes Théo Lebrun
2024-03-06 19:51 ` Linus Walleij
2024-03-07 23:11 ` Andi Shyti
2024-03-06 17:59 ` [PATCH v3 10/11] MIPS: mobileye: eyeq5: add 5 I2C controller nodes Théo Lebrun
2024-03-08 12:25 ` Andi Shyti
2024-03-06 17:59 ` [PATCH v3 11/11] MIPS: mobileye: eyeq5: add evaluation board I2C temp sensor Théo Lebrun
2024-03-08 12:26 ` Andi Shyti
2024-03-08 22:52 ` (subset) [PATCH v3 00/11] Add Mobileye EyeQ5 support to the Nomadik I2C controller & use hrtimers for timeouts Andi Shyti
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240306-mbly-i2c-v3-0-605f866aa4ec@bootlin.com \
--to=theo.lebrun@bootlin.com \
--cc=andi.shyti@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregory.clement@bootlin.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=tawfik.bayouk@mobileye.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=tsbogend@alpha.franken.de \
--cc=vladimir.kondratiev@mobileye.com \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).