From: Petr Tesarik <petrtesarik@huaweicloud.com>
To: Christoph Hellwig <hch@lst.de>,
Marek Szyprowski <m.szyprowski@samsung.com>,
Robin Murphy <robin.murphy@arm.com>,
Petr Tesarik <petr.tesarik1@huawei-partners.com>,
Michael Kelley <mhklinux@outlook.com>,
Will Deacon <will@kernel.org>,
linux-kernel@vger.kernel.org (open list),
iommu@lists.linux.dev (open list:DMA MAPPING HELPERS)
Cc: Roberto Sassu <roberto.sassu@huaweicloud.com>,
Petr Tesarik <petr@tesarici.cz>
Subject: [PATCH v2 1/2] swiotlb: extend buffer pre-padding to alloc_align_mask if necessary
Date: Mon, 18 Mar 2024 14:04:46 +0100 [thread overview]
Message-ID: <20240318130447.594-2-petrtesarik@huaweicloud.com> (raw)
In-Reply-To: <20240318130447.594-1-petrtesarik@huaweicloud.com>
From: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Allow a buffer pre-padding of up to alloc_align_mask. If the allocation
alignment is bigger than IO_TLB_SIZE and min_align_mask covers any non-zero
bits in the original address between IO_TLB_SIZE and alloc_align_mask,
these bits are not preserved in the swiotlb buffer address.
To fix this case, increase the allocation size and use a larger offset
within the allocated buffer. As a result, extra padding slots may be
allocated before the mapping start address.
Set the orig_addr in these padding slots to INVALID_PHYS_ADDR, because they
do not correspond to any CPU buffer and the data must never be synced.
The padding slots should be automatically released when the buffer is
unmapped. However, swiotlb_tbl_unmap_single() takes only the address of the
DMA buffer slot, not the first padding slot. Save the number of padding
slots in struct io_tlb_slot and use it to adjust the slot index in
swiotlb_release_slots(), so all allocated slots are properly freed.
Fixes: 2fd4fa5d3fb5 ("swiotlb: Fix alignment checks when both allocation and DMA masks are present")
Link: https://lore.kernel.org/linux-iommu/20240311210507.217daf8b@meshulam.tesarici.cz/
Signed-off-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
---
kernel/dma/swiotlb.c | 35 +++++++++++++++++++++++++++++------
1 file changed, 29 insertions(+), 6 deletions(-)
diff --git a/kernel/dma/swiotlb.c b/kernel/dma/swiotlb.c
index 86fe172b5958..aefb05ff55e7 100644
--- a/kernel/dma/swiotlb.c
+++ b/kernel/dma/swiotlb.c
@@ -69,11 +69,14 @@
* @alloc_size: Size of the allocated buffer.
* @list: The free list describing the number of free entries available
* from each index.
+ * @pad_slots: Number of preceding padding slots. Valid only in the first
+ * allocated non-padding slot.
*/
struct io_tlb_slot {
phys_addr_t orig_addr;
size_t alloc_size;
- unsigned int list;
+ unsigned short list;
+ unsigned short pad_slots;
};
static bool swiotlb_force_bounce;
@@ -287,6 +290,7 @@ static void swiotlb_init_io_tlb_pool(struct io_tlb_pool *mem, phys_addr_t start,
mem->nslabs - i);
mem->slots[i].orig_addr = INVALID_PHYS_ADDR;
mem->slots[i].alloc_size = 0;
+ mem->slots[i].pad_slots = 0;
}
memset(vaddr, 0, bytes);
@@ -1328,11 +1332,12 @@ phys_addr_t swiotlb_tbl_map_single(struct device *dev, phys_addr_t orig_addr,
unsigned long attrs)
{
struct io_tlb_mem *mem = dev->dma_io_tlb_mem;
- unsigned int offset = swiotlb_align_offset(dev, orig_addr);
+ unsigned int offset;
struct io_tlb_pool *pool;
unsigned int i;
int index;
phys_addr_t tlb_addr;
+ unsigned short pad_slots;
if (!mem || !mem->nslabs) {
dev_warn_ratelimited(dev,
@@ -1349,6 +1354,15 @@ phys_addr_t swiotlb_tbl_map_single(struct device *dev, phys_addr_t orig_addr,
return (phys_addr_t)DMA_MAPPING_ERROR;
}
+ /*
+ * Calculate buffer pre-padding within the allocated space. Use it to
+ * preserve the low bits of the original address according to device's
+ * min_align_mask. Limit the padding to alloc_align_mask or slot size
+ * (whichever is bigger); higher bits of the original address are
+ * preserved by selecting a suitable IO TLB slot.
+ */
+ offset = orig_addr & dma_get_min_align_mask(dev) &
+ (alloc_align_mask | (IO_TLB_SIZE - 1));
index = swiotlb_find_slots(dev, orig_addr,
alloc_size + offset, alloc_align_mask, &pool);
if (index == -1) {
@@ -1364,6 +1378,10 @@ phys_addr_t swiotlb_tbl_map_single(struct device *dev, phys_addr_t orig_addr,
* This is needed when we sync the memory. Then we sync the buffer if
* needed.
*/
+ pad_slots = offset / IO_TLB_SIZE;
+ offset %= IO_TLB_SIZE;
+ index += pad_slots;
+ pool->slots[index].pad_slots = i;
for (i = 0; i < nr_slots(alloc_size + offset); i++)
pool->slots[index + i].orig_addr = slot_addr(orig_addr, i);
tlb_addr = slot_addr(pool->start, index) + offset;
@@ -1385,12 +1403,16 @@ static void swiotlb_release_slots(struct device *dev, phys_addr_t tlb_addr)
struct io_tlb_pool *mem = swiotlb_find_pool(dev, tlb_addr);
unsigned long flags;
unsigned int offset = swiotlb_align_offset(dev, tlb_addr);
- int index = (tlb_addr - offset - mem->start) >> IO_TLB_SHIFT;
- int nslots = nr_slots(mem->slots[index].alloc_size + offset);
- int aindex = index / mem->area_nslabs;
- struct io_tlb_area *area = &mem->areas[aindex];
+ int index, nslots, aindex;
+ struct io_tlb_area *area;
int count, i;
+ index = (tlb_addr - offset - mem->start) >> IO_TLB_SHIFT;
+ index -= mem->slots[index].pad_slots;
+ nslots = nr_slots(mem->slots[index].alloc_size + offset);
+ aindex = index / mem->area_nslabs;
+ area = &mem->areas[aindex];
+
/*
* Return the buffer to the free list by setting the corresponding
* entries to indicate the number of contiguous entries available.
@@ -1413,6 +1435,7 @@ static void swiotlb_release_slots(struct device *dev, phys_addr_t tlb_addr)
mem->slots[i].list = ++count;
mem->slots[i].orig_addr = INVALID_PHYS_ADDR;
mem->slots[i].alloc_size = 0;
+ mem->slots[i].pad_slots = 0;
}
/*
--
2.34.1
next prev parent reply other threads:[~2024-03-18 13:05 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-03-18 13:04 [PATCH v2 0/2] swiotlb: allocate padding slots if necessary Petr Tesarik
2024-03-18 13:04 ` Petr Tesarik [this message]
2024-03-18 15:37 ` [PATCH v2 1/2] swiotlb: extend buffer pre-padding to alloc_align_mask " Michael Kelley
2024-03-18 18:50 ` Petr Tesařík
2024-03-19 4:45 ` kernel test robot
2024-03-18 13:04 ` [PATCH v2 2/2] bug: introduce ASSERT_VAR_CAN_HOLD() Petr Tesarik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240318130447.594-2-petrtesarik@huaweicloud.com \
--to=petrtesarik@huaweicloud.com \
--cc=hch@lst.de \
--cc=iommu@lists.linux.dev \
--cc=linux-kernel@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
--cc=mhklinux@outlook.com \
--cc=petr.tesarik1@huawei-partners.com \
--cc=petr@tesarici.cz \
--cc=roberto.sassu@huaweicloud.com \
--cc=robin.murphy@arm.com \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).