* Re: [Bug 217472] New: ACPI _OSC features have different values in Host OS and Guest OS
[not found] <bug-217472-41252@https.bugzilla.kernel.org/>
@ 2023-05-23 17:21 ` Bjorn Helgaas
2023-05-23 18:06 ` Alex Williamson
0 siblings, 1 reply; 4+ messages in thread
From: Bjorn Helgaas @ 2023-05-23 17:21 UTC (permalink / raw
To: linux-pci, kvm, linux-acpi; +Cc: Nirmal Patel, Alex Williamson
Hi Nirmal, thanks for the report!
On Mon, May 22, 2023 at 04:32:03PM +0000, bugzilla-daemon@kernel.org wrote:
> https://bugzilla.kernel.org/show_bug.cgi?id=217472
> ...
> Created attachment 304301
> --> https://bugzilla.kernel.org/attachment.cgi?id=304301&action=edit
> Rhel9.1_Guest_dmesg
>
> Issue:
> NVMe Drives are still present after performing hotplug in guest OS. We have
> tested with different combination of OSes, drives and Hypervisor. The issue is
> present across all the OSes.
Maybe attach the specific commands to reproduce the problem in one of
these scenarios to the bugzilla? I'm a virtualization noob, so I
can't visualize all the usual pieces.
> The following patch was added to honor ACPI _OSC values set by BIOS and the
> patch helped to bring the issue out in VM/ Guest OS.
>
> https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/commit/drivers/pci/controller/vmd.c?id=04b12ef163d10e348db664900ae7f611b83c7a0e
>
>
> I also compared the values of the parameters in the patch in Host and Guest OS.
> The parameters with different values in Host and Guest OS are:
>
> native_pcie_hotplug
> native_shpc_hotplug
> native_aer
> native_ltr
>
> i.e.
> value of native_pcie_hotplug in Host OS is 1.
> value of native_pcie_hotplug in Guest OS is 0.
>
> I am not sure why "native_pcie_hotplug" is changed to 0 in guest.
> Isn't it OSC_ managed parameter? If that is the case, it should
> have same value in Host and Guest OS.
From your dmesg:
DMI: Red Hat KVM/RHEL, BIOS 1.16.0-4.el9 04/01/2014
_OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
_OSC: platform does not support [PCIeHotplug LTR DPC]
_OSC: OS now controls [SHPCHotplug PME AER PCIeCapability]
acpiphp: Slot [0] registered
virtio_blk virtio3: [vda] 62914560 512-byte logical blocks (32.2 GB/30.0 GiB)
So the DMI ("KVM/RHEL ...") is the BIOS seen by the guest. Doesn't
mean anything to me, but the KVM folks would know about it. In any
event, the guest BIOS is different from the host BIOS, so I'm not
surprised that _OSC is different.
That guest BIOS _OSC declined to grant control of PCIe native hotplug
to the guest OS, so the guest will use acpiphp (not pciehp, which
would be used if native_pcie_hotplug were set).
The dmesg doesn't mention the nvme driver. Are you using something
like virtio_blk with qemu pointed at an NVMe drive? And you
hot-remove the NVMe device, but the guest OS thinks it's still
present?
Since the guest is using acpiphp, I would think a hot-remove of a host
NVMe device should be noticed by qemu and turned into an ACPI
notification that the guest OS would consume. But I don't know how
those connections work.
Bjorn
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Bug 217472] New: ACPI _OSC features have different values in Host OS and Guest OS
2023-05-23 17:21 ` [Bug 217472] New: ACPI _OSC features have different values in Host OS and Guest OS Bjorn Helgaas
@ 2023-05-23 18:06 ` Alex Williamson
[not found] ` <BYAPR11MB3031739869CB639695896CEF98469@BYAPR11MB3031.namprd11.prod.outlook.com>
0 siblings, 1 reply; 4+ messages in thread
From: Alex Williamson @ 2023-05-23 18:06 UTC (permalink / raw
To: Bjorn Helgaas; +Cc: linux-pci, kvm, linux-acpi, Nirmal Patel
On Tue, 23 May 2023 12:21:25 -0500
Bjorn Helgaas <helgaas@kernel.org> wrote:
> Hi Nirmal, thanks for the report!
>
> On Mon, May 22, 2023 at 04:32:03PM +0000, bugzilla-daemon@kernel.org wrote:
> > https://bugzilla.kernel.org/show_bug.cgi?id=217472
> > ...
>
> > Created attachment 304301
> > --> https://bugzilla.kernel.org/attachment.cgi?id=304301&action=edit
> > Rhel9.1_Guest_dmesg
> >
> > Issue:
> > NVMe Drives are still present after performing hotplug in guest OS. We have
> > tested with different combination of OSes, drives and Hypervisor. The issue is
> > present across all the OSes.
>
> Maybe attach the specific commands to reproduce the problem in one of
> these scenarios to the bugzilla? I'm a virtualization noob, so I
> can't visualize all the usual pieces.
>
> > The following patch was added to honor ACPI _OSC values set by BIOS and the
> > patch helped to bring the issue out in VM/ Guest OS.
> >
> > https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/commit/drivers/pci/controller/vmd.c?id=04b12ef163d10e348db664900ae7f611b83c7a0e
> >
> >
> > I also compared the values of the parameters in the patch in Host and Guest OS.
> > The parameters with different values in Host and Guest OS are:
> >
> > native_pcie_hotplug
> > native_shpc_hotplug
> > native_aer
> > native_ltr
> >
> > i.e.
> > value of native_pcie_hotplug in Host OS is 1.
> > value of native_pcie_hotplug in Guest OS is 0.
> >
> > I am not sure why "native_pcie_hotplug" is changed to 0 in guest.
> > Isn't it OSC_ managed parameter? If that is the case, it should
> > have same value in Host and Guest OS.
>
> From your dmesg:
>
> DMI: Red Hat KVM/RHEL, BIOS 1.16.0-4.el9 04/01/2014
> _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
> _OSC: platform does not support [PCIeHotplug LTR DPC]
> _OSC: OS now controls [SHPCHotplug PME AER PCIeCapability]
> acpiphp: Slot [0] registered
> virtio_blk virtio3: [vda] 62914560 512-byte logical blocks (32.2 GB/30.0 GiB)
>
> So the DMI ("KVM/RHEL ...") is the BIOS seen by the guest. Doesn't
> mean anything to me, but the KVM folks would know about it. In any
> event, the guest BIOS is different from the host BIOS, so I'm not
> surprised that _OSC is different.
Right, the premise of the issue that guest and host should have the
same OSC features is flawed. The guest is a virtual machine that can
present an entirely different feature set from the host. A software
hotplug on the guest can occur without any bearing to the slot status
on the host.
> That guest BIOS _OSC declined to grant control of PCIe native hotplug
> to the guest OS, so the guest will use acpiphp (not pciehp, which
> would be used if native_pcie_hotplug were set).
>
> The dmesg doesn't mention the nvme driver. Are you using something
> like virtio_blk with qemu pointed at an NVMe drive? And you
> hot-remove the NVMe device, but the guest OS thinks it's still
> present?
>
> Since the guest is using acpiphp, I would think a hot-remove of a host
> NVMe device should be noticed by qemu and turned into an ACPI
> notification that the guest OS would consume. But I don't know how
> those connections work.
If vfio-pci is involved, a cooperative hot-unplug will attempt to
unbind the host driver, which triggers a device request through vfio,
which is ultimately seen as a hotplug eject operation by the guest.
Surprise hotplugs of assigned devices are not supported. There's not
enough info in the bz to speculate how this VM is wired or what actions
are taken. Thanks,
Alex
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: FW: [Bug 217472] New: ACPI _OSC features have different values in Host OS and Guest OS
[not found] ` <1f7f84a4-0df4-a413-ba30-cc2257980abd@linux.intel.com>
@ 2023-05-25 20:33 ` Patel, Nirmal
2023-06-06 23:41 ` Bjorn Helgaas
0 siblings, 1 reply; 4+ messages in thread
From: Patel, Nirmal @ 2023-05-25 20:33 UTC (permalink / raw
To: Bjorn Helgaas, Alex Williamson; +Cc: linux-pci, kvm, linux-acpi
On 5/25/2023 1:19 PM, Patel, Nirmal wrote:
>> On Tue, 23 May 2023 12:21:25 -0500
>> Bjorn Helgaas <helgaas@kernel.org> wrote:
>>
>>> Hi Nirmal, thanks for the report!
>>>
>>> On Mon, May 22, 2023 at 04:32:03PM +0000, bugzilla-daemon@kernel.org wrote:
>>>> https://bugzilla.kernel.org/show_bug.cgi?id=217472
>>>> ...
>>>> Created attachment 304301
>>>> -->
>>>> https://bugzilla.kernel.org/attachment.cgi?id=304301&action=edit
>>>> Rhel9.1_Guest_dmesg
>>>>
>>>> Issue:
>>>> NVMe Drives are still present after performing hotplug in guest OS.
>>>> We have tested with different combination of OSes, drives and Hypervisor. The issue is
>>>> present across all the OSes.
>>> Maybe attach the specific commands to reproduce the problem in one of
>>> these scenarios to the bugzilla? I'm a virtualization noob, so I
>>> can't visualize all the usual pieces.
>>>
>>>> The following patch was added to honor ACPI _OSC values set by BIOS
>>>> and the patch helped to bring the issue out in VM/ Guest OS.
>>>>
>>>> https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/comm
>>>> it/drivers/pci/controller/vmd.c?id=04b12ef163d10e348db664900ae7f611b
>>>> 83c7a0e
>>>>
>>>>
>>>> I also compared the values of the parameters in the patch in Host and Guest OS.
>>>> The parameters with different values in Host and Guest OS are:
>>>>
>>>> native_pcie_hotplug
>>>> native_shpc_hotplug
>>>> native_aer
>>>> native_ltr
>>>>
>>>> i.e.
>>>> value of native_pcie_hotplug in Host OS is 1.
>>>> value of native_pcie_hotplug in Guest OS is 0.
>>>>
>>>> I am not sure why "native_pcie_hotplug" is changed to 0 in guest.
>>>> Isn't it OSC_ managed parameter? If that is the case, it should have
>>>> same value in Host and Guest OS.
>>> From your dmesg:
>>>
>>> DMI: Red Hat KVM/RHEL, BIOS 1.16.0-4.el9 04/01/2014
>>> _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
>>> _OSC: platform does not support [PCIeHotplug LTR DPC]
>>> _OSC: OS now controls [SHPCHotplug PME AER PCIeCapability]
>>> acpiphp: Slot [0] registered
>>> virtio_blk virtio3: [vda] 62914560 512-byte logical blocks (32.2
>>> GB/30.0 GiB)
>>>
>>> So the DMI ("KVM/RHEL ...") is the BIOS seen by the guest. Doesn't
>>> mean anything to me, but the KVM folks would know about it. In any
>>> event, the guest BIOS is different from the host BIOS, so I'm not
>>> surprised that _OSC is different.
>> Right, the premise of the issue that guest and host should have the same OSC features is flawed. The guest is a virtual machine that can present an entirely different feature set from the host. A software hotplug on the guest can occur without any bearing to the slot status on the host.
>>
>>> That guest BIOS _OSC declined to grant control of PCIe native hotplug
>>> to the guest OS, so the guest will use acpiphp (not pciehp, which
>>> would be used if native_pcie_hotplug were set).
>>>
>>> The dmesg doesn't mention the nvme driver. Are you using something
>>> like virtio_blk with qemu pointed at an NVMe drive? And you
>>> hot-remove the NVMe device, but the guest OS thinks it's still
>>> present?
>>>
>>> Since the guest is using acpiphp, I would think a hot-remove of a host
>>> NVMe device should be noticed by qemu and turned into an ACPI
>>> notification that the guest OS would consume. But I don't know how
>>> those connections work.
>> If vfio-pci is involved, a cooperative hot-unplug will attempt to unbind the host driver, which triggers a device request through vfio, which is ultimately seen as a hotplug eject operation by the guest.
>> Surprise hotplugs of assigned devices are not supported. There's not enough info in the bz to speculate how this VM is wired or what actions are taken. Thanks,
>>
>> Alex
Thanks Bjorn and Alex for quick response.
I agree with the analysis about guest BIOS not giving control of PCIe native hotplug to guest OS.
Adding some background about the patch f611b83c7a0e PCI: vmd: Honor ACPI _OSC on PCIe features.
The above patch was added to suppress AER messages when samsung drives were connected with VMD enabled. I believe AER was enabled in BIOS i.e. pre-OS VMD driver not by VMD linux driver. So the AER flooding would be seen even non-linux environment.
So with guest BIOS providing different values than the Host BIOS and adding this patch in VMD linux driver leaves direct assign functionality broken across all the hypervisors and guest OS combinations. As a result hotplug will not work which is a major issue.
Before this patch, VMD used pciehp.
What should be the ideal case here?
I am open to a better suggestion, but I can think of two options.
Option 1: Revert the patch f611b83c7a0e and suggest the AER fix to be added to the BIOS or Pre-OS vmd driver.
Option 2: VMD to enumerate all the devices and set native_pcie_hotplug for all the hotplug capable devices.
Thanks
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: FW: [Bug 217472] New: ACPI _OSC features have different values in Host OS and Guest OS
2023-05-25 20:33 ` FW: " Patel, Nirmal
@ 2023-06-06 23:41 ` Bjorn Helgaas
0 siblings, 0 replies; 4+ messages in thread
From: Bjorn Helgaas @ 2023-06-06 23:41 UTC (permalink / raw
To: Patel, Nirmal; +Cc: Alex Williamson, linux-pci, kvm, linux-acpi, Bagas Sanjaya
[+cc Bagas]
On Thu, May 25, 2023 at 01:33:27PM -0700, Patel, Nirmal wrote:
> On 5/25/2023 1:19 PM, Patel, Nirmal wrote:
> >> On Tue, 23 May 2023 12:21:25 -0500
> >> Bjorn Helgaas <helgaas@kernel.org> wrote:
> >>> On Mon, May 22, 2023 at 04:32:03PM +0000, bugzilla-daemon@kernel.org wrote:
> >>>> https://bugzilla.kernel.org/show_bug.cgi?id=217472
> >>>> ...
> >>>> Created attachment 304301
> >>>> -->
> >>>> https://bugzilla.kernel.org/attachment.cgi?id=304301&action=edit
> >>>> Rhel9.1_Guest_dmesg
> >>>>
> >>>> Issue:
> >>>> NVMe Drives are still present after performing hotplug in guest
> >>>> OS. We have tested with different combination of OSes, drives
> >>>> and Hypervisor. The issue is present across all the OSes.
> >>>
> >>> Maybe attach the specific commands to reproduce the problem in one of
> >>> these scenarios to the bugzilla? I'm a virtualization noob, so I
> >>> can't visualize all the usual pieces.
> >>>
> >>>> The following patch was added to honor ACPI _OSC values set by BIOS
> >>>> and the patch helped to bring the issue out in VM/ Guest OS.
> >>>>
> >>>> https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/comm
> >>>> it/drivers/pci/controller/vmd.c?id=04b12ef163d10e348db664900ae7f611b
> >>>> 83c7a0e
> >>>>
> >>>>
> >>>> I also compared the values of the parameters in the patch in
> >>>> Host and Guest OS. The parameters with different values in
> >>>> Host and Guest OS are:
> >>>>
> >>>> native_pcie_hotplug
> >>>> native_shpc_hotplug
> >>>> native_aer
> >>>> native_ltr
> >>>>
> >>>> i.e.
> >>>> value of native_pcie_hotplug in Host OS is 1.
> >>>> value of native_pcie_hotplug in Guest OS is 0.
> >>>>
> >>>> I am not sure why "native_pcie_hotplug" is changed to 0 in guest.
> >>>> Isn't it OSC_ managed parameter? If that is the case, it should have
> >>>> same value in Host and Guest OS.
> >>>
> >>> From your dmesg:
> >>>
> >>> DMI: Red Hat KVM/RHEL, BIOS 1.16.0-4.el9 04/01/2014
> >>> _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
> >>> _OSC: platform does not support [PCIeHotplug LTR DPC]
> >>> _OSC: OS now controls [SHPCHotplug PME AER PCIeCapability]
> >>> acpiphp: Slot [0] registered
> >>> virtio_blk virtio3: [vda] 62914560 512-byte logical blocks (32.2
> >>> GB/30.0 GiB)
> >>>
> >>> So the DMI ("KVM/RHEL ...") is the BIOS seen by the guest. Doesn't
> >>> mean anything to me, but the KVM folks would know about it. In any
> >>> event, the guest BIOS is different from the host BIOS, so I'm not
> >>> surprised that _OSC is different.
> >>
> >> Right, the premise of the issue that guest and host should have
> >> the same OSC features is flawed. The guest is a virtual machine
> >> that can present an entirely different feature set from the host.
> >> A software hotplug on the guest can occur without any bearing to
> >> the slot status on the host.
> >>
> >>> That guest BIOS _OSC declined to grant control of PCIe native
> >>> hotplug to the guest OS, so the guest will use acpiphp (not
> >>> pciehp, which would be used if native_pcie_hotplug were set).
> >>>
> >>> The dmesg doesn't mention the nvme driver. Are you using
> >>> something like virtio_blk with qemu pointed at an NVMe drive?
> >>> And you hot-remove the NVMe device, but the guest OS thinks it's
> >>> still present?
> >>>
> >>> Since the guest is using acpiphp, I would think a hot-remove of
> >>> a host NVMe device should be noticed by qemu and turned into an
> >>> ACPI notification that the guest OS would consume. But I don't
> >>> know how those connections work.
> >>
> >> If vfio-pci is involved, a cooperative hot-unplug will attempt to
> >> unbind the host driver, which triggers a device request through
> >> vfio, which is ultimately seen as a hotplug eject operation by
> >> the guest. Surprise hotplugs of assigned devices are not
> >> supported. There's not enough info in the bz to speculate how
> >> this VM is wired or what actions are taken. Thanks,
>
> Thanks Bjorn and Alex for quick response.
> I agree with the analysis about guest BIOS not giving control of
> PCIe native hotplug to guest OS.
Can I back up and try to understand the problem better? I'm sure I'm
asking dumb questions, so please correct me:
- Can you add more details in the bz about what you're doing and
what is failing?
- I have the impression that the hotplug worked before 04b12ef163d1
("PCI: vmd: Honor ACPI _OSC on PCIe features") but fails after?
- Can you attach dmesg logs from before and after 04b12ef163d1?
- What sort of virtualized guest is this? qemu?
- How is the NVMe drive passed to the guest? vfio-pci?
- Apparently the problem is with a hot-remove in the guest? How are
you doing this? Sysfs "remove" file? qemu "device_del"?
- I assume this hot-remove is only from the *guest* and there's no
hotplug event for the *host*?
> Adding some background about the patch f611b83c7a0e PCI: vmd: Honor
> ACPI _OSC on PCIe features.
Tangent, "f611b83c7a0e" is not a valid SHA1, so I was lost for a minute :)
I guess you're referring to 04b12ef163d10e348db664900ae7f611b83c7a0e,
where f611b83c7a0e is at the *end* of the SHA1. You can abbreviate
it, but you have to quote the *beginning*, not the end. E.g., the
conventional style would be 04b12ef163d1 ("PCI: vmd: Honor ACPI _OSC
on PCIe features").
Bjorn
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2023-06-06 23:41 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <bug-217472-41252@https.bugzilla.kernel.org/>
2023-05-23 17:21 ` [Bug 217472] New: ACPI _OSC features have different values in Host OS and Guest OS Bjorn Helgaas
2023-05-23 18:06 ` Alex Williamson
[not found] ` <BYAPR11MB3031739869CB639695896CEF98469@BYAPR11MB3031.namprd11.prod.outlook.com>
[not found] ` <1f7f84a4-0df4-a413-ba30-cc2257980abd@linux.intel.com>
2023-05-25 20:33 ` FW: " Patel, Nirmal
2023-06-06 23:41 ` Bjorn Helgaas
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).