[Buildroot] imx93-evk: Fails to boot from the SD card

From: Fabio Estevam <festevam@gmail.com>
To: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>,
	"Julien Olivain" <ju.o@free.fr>
Cc: buildroot <buildroot@buildroot.org>
Subject: [Buildroot] imx93-evk: Fails to boot from the SD card
Date: Mon, 13 May 2024 08:39:38 -0300	[thread overview]
Message-ID: <CAOMZO5BFKyfF8WpZC9W=1uH0C4mNzZfHTADJTtDc4epxdnLDCg@mail.gmail.com> (raw)

Hi Sébastien and Julien,

I built an image for freescale_imx93evk_defconfig using the top of
tree Buildroot, flashed the sdcard.img into an SD card an put the boot
switch to SD card boot mode, but the image fails to boot:

U-Boot SPL 2023.04 (Apr 28 2024 - 10:59:35 -0300)
SOC: 0xa1009300
LC: 0x2040010
PMIC: Over Drive Voltage Mode
DDR: 3733MTS
M33 prepare ok
Normal Boot
Trying to boot from BOOTROM
Boot Stage: Primary boot
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x56800 by ROM_API
NOTICE:  BL31: v2.8(release):custom
NOTICE:  BL31: Built : 10:55:27, Apr 28 2024

U-Boot 2023.04 (Apr 28 2024 - 10:59:35 -0300)

CPU:   i.MX93(52) rev1.1 1700 MHz (running at 1692 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR (0x1)
Model: NXP i.MX93 11X11 EVK board
DRAM:  2 GiB
optee optee: OP-TEE api uid mismatch
TCPC:  Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x52]
SNK.Power3.0 on CC1
PDO 0: type 0, 5000 mV, 3000 mA [E]
PDO 1: type 0, 9000 mV, 3000 mA []
PDO 2: type 0, 15000 mV, 3000 mA []
PDO 3: type 0, 20000 mV, 2250 mA []
Requesting PDO 3: 20000 mV, 750 mA
Source accept request
PD source ready!
tcpc_pd_receive_message: Polling ALERT register, TCPC_ALERT_RX_STATUS
bit failed, ret = -62
TCPC:  Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x51]
TCPC:  Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x50]
Core:  229 devices, 36 uclasses, devicetree: separate
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using
default environment

[*]-Video Link 0adv7535_mipi2hdmi hdmi@3d: Can't find cec device id=0x3c
fail to probe panel device hdmi@3d
fail to get display timings
probe video device failed, ret -19

[0] lcd-controller@4ae30000, video
[1] dsi@4ae10000, video_bridge
[2] hdmi@3d, panel
adv7535_mipi2hdmi hdmi@3d: Can't find cec device id=0x3c
fail to probe panel device hdmi@3d
fail to get display timings
probe video device failed, ret -19
In:    serial
Out:   serial
Err:   serial

BuildInfo:
  - ELE firmware version 0.1.0-44880904

UID: 0x6280a860 0x58465520 0x9883799f 0x311012fb
flash target is MMC:1
MMC card init failed!
** Block device MMC 1 not supported

The SD card is not recognized.

Would you happen to have any suggestions?

Thanks,

Fabio Estevam
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot