* QCN9274 - x64 - AMD or Intel [not found] <LO0P123MB4057B28CB310E5A1CEEF92F0D6002@LO0P123MB4057.GBRP123.PROD.OUTLOOK.COM> @ 2024-04-10 14:52 ` david Atkins 2024-04-10 16:57 ` Jeff Johnson 0 siblings, 1 reply; 6+ messages in thread From: david Atkins @ 2024-04-10 14:52 UTC (permalink / raw To: ath12k@lists.infradead.org I just built the ath-next branch for my AMD Ryzen 3 4300U system with an 8devices QCN9274 module, it appears to have a new message memory type 10 not supported in the dmesg logs [ 2.705656] ath12k_pci 0000:03:00.0: BAR 0 [mem 0xfe200000-0xfe3fffff 64bit]: assigned [ 2.705672] ath12k_pci 0000:03:00.0: enabling device (0000 -> 0002) [ 2.705885] ath12k_pci 0000:03:00.0: MSI vectors: 16 [ 2.705889] ath12k_pci 0000:03:00.0: Hardware name: qcn9274 hw2.0 [ 3.405328] ath12k_pci 0000:03:00.0: memory type 10 not supported [ 3.410796] ath12k_pci 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id 0xc soc_id 0x401a2200 [ 3.410804] ath12k_pci 0000:03:00.0: fw_version 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 [ 3.431347] ath12k_pci 0000:03:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=12 from ath12k/QCN9274/hw2.0/board-2.bin [ 3.431375] ath12k_pci 0000:03:00.0: failed to fetch board.bin from QCN9274/hw2.0 [ 3.431386] ath12k_pci 0000:03:00.0: qmi failed to load bdf: [ 3.431387] ath12k_pci 0000:03:00.0: qmi failed to load board data file:-2 I'll try on my other test bed systems, but is it expected that this will get further than this ? System uname -a Linux openwrt-wifi-test 6.9.0-rc1+ #3 SMP PREEMPT_DYNAMIC Mon Apr 8 07:47:14 BST 2024 x86_64 x86_64 x86_64 GNU/Linux David David Atkins ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: QCN9274 - x64 - AMD or Intel 2024-04-10 14:52 ` QCN9274 - x64 - AMD or Intel david Atkins @ 2024-04-10 16:57 ` Jeff Johnson 2024-04-10 19:02 ` Jeff Johnson 2024-04-11 8:35 ` Kalle Valo 0 siblings, 2 replies; 6+ messages in thread From: Jeff Johnson @ 2024-04-10 16:57 UTC (permalink / raw To: david Atkins, ath12k@lists.infradead.org On 4/10/2024 7:52 AM, david Atkins wrote: > > I just built the ath-next branch for my AMD Ryzen 3 4300U system with an 8devices QCN9274 module, it appears to have a new message > > memory type 10 not supported > > in the dmesg logs > > [ 2.705656] ath12k_pci 0000:03:00.0: BAR 0 [mem 0xfe200000-0xfe3fffff 64bit]: assigned > [ 2.705672] ath12k_pci 0000:03:00.0: enabling device (0000 -> 0002) > [ 2.705885] ath12k_pci 0000:03:00.0: MSI vectors: 16 > [ 2.705889] ath12k_pci 0000:03:00.0: Hardware name: qcn9274 hw2.0 > [ 3.405328] ath12k_pci 0000:03:00.0: memory type 10 not supported > [ 3.410796] ath12k_pci 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id 0xc soc_id 0x401a2200 > [ 3.410804] ath12k_pci 0000:03:00.0: fw_version 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 > [ 3.431347] ath12k_pci 0000:03:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=12 from ath12k/QCN9274/hw2.0/board-2.bin > [ 3.431375] ath12k_pci 0000:03:00.0: failed to fetch board.bin from QCN9274/hw2.0 > [ 3.431386] ath12k_pci 0000:03:00.0: qmi failed to load bdf: > [ 3.431387] ath12k_pci 0000:03:00.0: qmi failed to load board data file:-2 > > I'll try on my other test bed systems, but is it expected that this will get further than this ? I believe the memory type 10 message can be ignored (I've received conflicting information on that) You need to get the board file in place. Please grab the one at: https://git.codelinaro.org/clo/ath-firmware/ath12k-firmware/-/blob/main/QCN9274/hw2.0/board-2.bin And place it in <firmware>/ath12k/QCN9274/hw2.0/ ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: QCN9274 - x64 - AMD or Intel 2024-04-10 16:57 ` Jeff Johnson @ 2024-04-10 19:02 ` Jeff Johnson 2024-04-28 12:50 ` david Atkins 2024-04-11 8:35 ` Kalle Valo 1 sibling, 1 reply; 6+ messages in thread From: Jeff Johnson @ 2024-04-10 19:02 UTC (permalink / raw To: david Atkins, ath12k@lists.infradead.org On 4/10/2024 9:57 AM, Jeff Johnson wrote: > On 4/10/2024 7:52 AM, david Atkins wrote: >> >> I just built the ath-next branch for my AMD Ryzen 3 4300U system with an 8devices QCN9274 module, it appears to have a new message >> >> memory type 10 not supported >> >> in the dmesg logs >> >> [ 2.705656] ath12k_pci 0000:03:00.0: BAR 0 [mem 0xfe200000-0xfe3fffff 64bit]: assigned >> [ 2.705672] ath12k_pci 0000:03:00.0: enabling device (0000 -> 0002) >> [ 2.705885] ath12k_pci 0000:03:00.0: MSI vectors: 16 >> [ 2.705889] ath12k_pci 0000:03:00.0: Hardware name: qcn9274 hw2.0 >> [ 3.405328] ath12k_pci 0000:03:00.0: memory type 10 not supported >> [ 3.410796] ath12k_pci 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id 0xc soc_id 0x401a2200 >> [ 3.410804] ath12k_pci 0000:03:00.0: fw_version 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 >> [ 3.431347] ath12k_pci 0000:03:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=12 from ath12k/QCN9274/hw2.0/board-2.bin >> [ 3.431375] ath12k_pci 0000:03:00.0: failed to fetch board.bin from QCN9274/hw2.0 >> [ 3.431386] ath12k_pci 0000:03:00.0: qmi failed to load bdf: >> [ 3.431387] ath12k_pci 0000:03:00.0: qmi failed to load board data file:-2 >> >> I'll try on my other test bed systems, but is it expected that this will get further than this ? > > I believe the memory type 10 message can be ignored (I've received conflicting information on that) > > You need to get the board file in place. Please grab the one at: > https://git.codelinaro.org/clo/ath-firmware/ath12k-firmware/-/blob/main/QCN9274/hw2.0/board-2.bin > > And place it in <firmware>/ath12k/QCN9274/hw2.0/ Based upon further information it seems your card is advertising a board_id that our default board file may not support, so you should contact 8devices to see if they have a customized board file for that device. /jeff ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: QCN9274 - x64 - AMD or Intel 2024-04-10 19:02 ` Jeff Johnson @ 2024-04-28 12:50 ` david Atkins 2024-05-03 7:07 ` david Atkins 0 siblings, 1 reply; 6+ messages in thread From: david Atkins @ 2024-04-28 12:50 UTC (permalink / raw To: Jeff Johnson, ath12k@lists.infradead.org > -----Original Message----- > From: Jeff Johnson <quic_jjohnson@quicinc.com> > Sent: Wednesday, April 10, 2024 8:02 PM > To: david Atkins <david@3adesign.co.uk>; ath12k@lists.infradead.org > Subject: Re: QCN9274 - x64 - AMD or Intel > > On 4/10/2024 9:57 AM, Jeff Johnson wrote: > > On 4/10/2024 7:52 AM, david Atkins wrote: > >> > >> I just built the ath-next branch for my AMD Ryzen 3 4300U system with > >> an 8devices QCN9274 module, it appears to have a new message > >> > >> memory type 10 not supported > >> > >> in the dmesg logs > >> > >> [ 2.705656] ath12k_pci 0000:03:00.0: BAR 0 [mem > >> 0xfe200000-0xfe3fffff 64bit]: assigned [ 2.705672] ath12k_pci > >> 0000:03:00.0: enabling device (0000 -> 0002) [ 2.705885] > >> ath12k_pci 0000:03:00.0: MSI vectors: 16 [ 2.705889] ath12k_pci > >> 0000:03:00.0: Hardware name: qcn9274 hw2.0 [ 3.405328] ath12k_pci > >> 0000:03:00.0: memory type 10 not supported [ 3.410796] ath12k_pci > >> 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id 0xc soc_id > >> 0x401a2200 [ 3.410804] ath12k_pci 0000:03:00.0: fw_version > >> 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id > >> QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029- > QCAHKSWPL_SILICONZ-1 > >> [ 3.431347] ath12k_pci 0000:03:00.0: failed to fetch board data > >> for bus=pci,qmi-chip-id=0,qmi-board-id=12 from > >> ath12k/QCN9274/hw2.0/board-2.bin [ 3.431375] ath12k_pci > 0000:03:00.0: failed to fetch board.bin from QCN9274/hw2.0 [ 3.431386] > ath12k_pci 0000:03:00.0: qmi failed to load bdf: > >> [ 3.431387] ath12k_pci 0000:03:00.0: qmi failed to load board data > >> file:-2 > >> > >> I'll try on my other test bed systems, but is it expected that this will get > further than this ? > > > > I believe the memory type 10 message can be ignored (I've received > > conflicting information on that) > > > > You need to get the board file in place. Please grab the one at: > > https://git.codelinaro.org/clo/ath-firmware/ath12k-firmware/-/blob/mai > > n/QCN9274/hw2.0/board-2.bin > > > > And place it in <firmware>/ath12k/QCN9274/hw2.0/ > > Based upon further information it seems your card is advertising a board_id > that our default board file may not support, so you should contact 8devices to > see if they have a customized board file for that device. > > /jeff Got updated firmware from 8devices, it is not working but does now show up as a wlp device $ sudo dmesg | grep ath12 [ 2.620901] ath12k_pci 0000:03:00.0: BAR 0 [mem 0xfe200000-0xfe3fffff 64bit]: assigned [ 2.620918] ath12k_pci 0000:03:00.0: enabling device (0000 -> 0002) [ 2.621139] ath12k_pci 0000:03:00.0: MSI vectors: 16 [ 2.621142] ath12k_pci 0000:03:00.0: Hardware name: qcn9274 hw2.0 [ 3.387645] ath12k_pci 0000:03:00.0: memory type 10 not supported [ 3.392254] ath12k_pci 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id 0xc soc_id 0x401a2200 [ 3.392260] ath12k_pci 0000:03:00.0: fw_version 0x11010cf9 fw_build_timestamp 2024-02-02 07:43 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.1-03321-QCAHKSWPL_SILICONZ-1 [ 6.164203] ath12k_pci 0000:03:00.0: HTC Service WMI MAC1 connect request failed: 0x1) [ 6.164227] ath12k_pci 0000:03:00.0: failed to connect to WMI CONTROL service status: -71 [ 6.164748] ath12k_pci 0000:03:00.0: Invalid module id 2 [ 6.164753] ath12k_pci 0000:03:00.0: failed to parse tlv -22 [ 6.472567] ath12k_pci 0000:03:00.0 wlp3s0: renamed from wlan0 [ 8.584409] ath12k_pci 0000:03:00.0: firmware crashed: MHI_CB_SYS_ERROR [ 18.395177] ath12k_pci 0000:03:00.0: failed to send WMI_STOP_SCAN_CMDID [ 18.395185] ath12k_pci 0000:03:00.0: failed to stop wmi scan: -108 [ 18.395194] ath12k_pci 0000:03:00.0: failed to abort scan: -108 [ 18.619059] ath12k_pci 0000:03:00.0: failed to send WMI_START_SCAN_CMDID [ 18.619070] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 [ 23.001923] ath12k_pci 0000:03:00.0: failed to send WMI_START_SCAN_CMDID [ 23.001934] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 [ 30.002943] ath12k_pci 0000:03:00.0: failed to send WMI_START_SCAN_CMDID [ 30.002954] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 [ 40.003342] ath12k_pci 0000:03:00.0: failed to send WMI_START_SCAN_CMDID [ 40.003354] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 [ 54.002922] ath12k_pci 0000:03:00.0: failed to send WMI_START_SCAN_CMDID [ 54.002932] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 [ 74.002086] ath12k_pci 0000:03:00.0: failed to send WMI_START_SCAN_CMDID Ip a results 4: wlp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000 link/ether c4:93:00:4c:cd:14 brd ff:ff:ff:ff:ff:ff nmcli wlp3s0: disconnected "Qualcomm Renoir/Cezanne GPP Bridge" wifi (ath12k_pci), C4:93:00:4C:CD:14, hw, mtu 1500 david ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: QCN9274 - x64 - AMD or Intel 2024-04-28 12:50 ` david Atkins @ 2024-05-03 7:07 ` david Atkins 0 siblings, 0 replies; 6+ messages in thread From: david Atkins @ 2024-05-03 7:07 UTC (permalink / raw To: david Atkins, Jeff Johnson, ath12k@lists.infradead.org Any thoughts on this? > -----Original Message----- > From: ath12k <ath12k-bounces@lists.infradead.org> On Behalf Of david > Atkins > Sent: Sunday, April 28, 2024 1:50 PM > To: Jeff Johnson <quic_jjohnson@quicinc.com>; ath12k@lists.infradead.org > Subject: RE: QCN9274 - x64 - AMD or Intel > > > -----Original Message----- > > From: Jeff Johnson <quic_jjohnson@quicinc.com> > > Sent: Wednesday, April 10, 2024 8:02 PM > > To: david Atkins <david@3adesign.co.uk>; ath12k@lists.infradead.org > > Subject: Re: QCN9274 - x64 - AMD or Intel > > > > On 4/10/2024 9:57 AM, Jeff Johnson wrote: > > > On 4/10/2024 7:52 AM, david Atkins wrote: > > >> > > >> I just built the ath-next branch for my AMD Ryzen 3 4300U system > > >> with an 8devices QCN9274 module, it appears to have a new message > > >> > > >> memory type 10 not supported > > >> > > >> in the dmesg logs > > >> > > >> [ 2.705656] ath12k_pci 0000:03:00.0: BAR 0 [mem > > >> 0xfe200000-0xfe3fffff 64bit]: assigned [ 2.705672] ath12k_pci > > >> 0000:03:00.0: enabling device (0000 -> 0002) [ 2.705885] > > >> ath12k_pci 0000:03:00.0: MSI vectors: 16 [ 2.705889] ath12k_pci > > >> 0000:03:00.0: Hardware name: qcn9274 hw2.0 [ 3.405328] > > >> ath12k_pci > > >> 0000:03:00.0: memory type 10 not supported [ 3.410796] > > >> ath12k_pci > > >> 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id 0xc soc_id > > >> 0x401a2200 [ 3.410804] ath12k_pci 0000:03:00.0: fw_version > > >> 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id > > >> QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029- > > QCAHKSWPL_SILICONZ-1 > > >> [ 3.431347] ath12k_pci 0000:03:00.0: failed to fetch board data > > >> for bus=pci,qmi-chip-id=0,qmi-board-id=12 from > > >> ath12k/QCN9274/hw2.0/board-2.bin [ 3.431375] ath12k_pci > > 0000:03:00.0: failed to fetch board.bin from QCN9274/hw2.0 [ > > 3.431386] ath12k_pci 0000:03:00.0: qmi failed to load bdf: > > >> [ 3.431387] ath12k_pci 0000:03:00.0: qmi failed to load board > > >> data > > >> file:-2 > > >> > > >> I'll try on my other test bed systems, but is it expected that this > > >> will get > > further than this ? > > > > > > I believe the memory type 10 message can be ignored (I've received > > > conflicting information on that) > > > > > > You need to get the board file in place. Please grab the one at: > > > https://git.codelinaro.org/clo/ath-firmware/ath12k-firmware/-/blob/m > > > ai > > > n/QCN9274/hw2.0/board-2.bin > > > > > > And place it in <firmware>/ath12k/QCN9274/hw2.0/ > > > > Based upon further information it seems your card is advertising a > > board_id that our default board file may not support, so you should > > contact 8devices to see if they have a customized board file for that device. > > > > /jeff > > Got updated firmware from 8devices, it is not working but does now show up > as a wlp device > > $ sudo dmesg | grep ath12 > [ 2.620901] ath12k_pci 0000:03:00.0: BAR 0 [mem 0xfe200000-0xfe3fffff > 64bit]: assigned > [ 2.620918] ath12k_pci 0000:03:00.0: enabling device (0000 -> 0002) > [ 2.621139] ath12k_pci 0000:03:00.0: MSI vectors: 16 > [ 2.621142] ath12k_pci 0000:03:00.0: Hardware name: qcn9274 hw2.0 > [ 3.387645] ath12k_pci 0000:03:00.0: memory type 10 not supported > [ 3.392254] ath12k_pci 0000:03:00.0: chip_id 0x0 chip_family 0xb board_id > 0xc soc_id 0x401a2200 > [ 3.392260] ath12k_pci 0000:03:00.0: fw_version 0x11010cf9 > fw_build_timestamp 2024-02-02 07:43 fw_build_id > QC_IMAGE_VERSION_STRING=WLAN.WBE.1.1-03321-QCAHKSWPL_SILICONZ- > 1 > [ 6.164203] ath12k_pci 0000:03:00.0: HTC Service WMI MAC1 connect > request failed: 0x1) > [ 6.164227] ath12k_pci 0000:03:00.0: failed to connect to WMI CONTROL > service status: -71 > [ 6.164748] ath12k_pci 0000:03:00.0: Invalid module id 2 > [ 6.164753] ath12k_pci 0000:03:00.0: failed to parse tlv -22 > [ 6.472567] ath12k_pci 0000:03:00.0 wlp3s0: renamed from wlan0 > [ 8.584409] ath12k_pci 0000:03:00.0: firmware crashed: > MHI_CB_SYS_ERROR > [ 18.395177] ath12k_pci 0000:03:00.0: failed to send > WMI_STOP_SCAN_CMDID > [ 18.395185] ath12k_pci 0000:03:00.0: failed to stop wmi scan: -108 > [ 18.395194] ath12k_pci 0000:03:00.0: failed to abort scan: -108 > [ 18.619059] ath12k_pci 0000:03:00.0: failed to send > WMI_START_SCAN_CMDID > [ 18.619070] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 > [ 23.001923] ath12k_pci 0000:03:00.0: failed to send > WMI_START_SCAN_CMDID > [ 23.001934] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 > [ 30.002943] ath12k_pci 0000:03:00.0: failed to send > WMI_START_SCAN_CMDID > [ 30.002954] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 > [ 40.003342] ath12k_pci 0000:03:00.0: failed to send > WMI_START_SCAN_CMDID > [ 40.003354] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 > [ 54.002922] ath12k_pci 0000:03:00.0: failed to send > WMI_START_SCAN_CMDID > [ 54.002932] ath12k_pci 0000:03:00.0: failed to start hw scan: -108 > [ 74.002086] ath12k_pci 0000:03:00.0: failed to send > WMI_START_SCAN_CMDID > > Ip a results > > 4: wlp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc > noqueue state DOWN group default qlen 1000 > link/ether c4:93:00:4c:cd:14 brd ff:ff:ff:ff:ff:ff > > nmcli > > > wlp3s0: disconnected > "Qualcomm Renoir/Cezanne GPP Bridge" > wifi (ath12k_pci), C4:93:00:4C:CD:14, hw, mtu 1500 > > david > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: QCN9274 - x64 - AMD or Intel 2024-04-10 16:57 ` Jeff Johnson 2024-04-10 19:02 ` Jeff Johnson @ 2024-04-11 8:35 ` Kalle Valo 1 sibling, 0 replies; 6+ messages in thread From: Kalle Valo @ 2024-04-11 8:35 UTC (permalink / raw To: Jeff Johnson; +Cc: david Atkins, ath12k@lists.infradead.org Jeff Johnson <quic_jjohnson@quicinc.com> writes: > On 4/10/2024 7:52 AM, david Atkins wrote: > >> >> I just built the ath-next branch for my AMD Ryzen 3 4300U system >> with an 8devices QCN9274 module, it appears to have a new message >> >> memory type 10 not supported >> >> in the dmesg logs >> >> [ 2.705656] ath12k_pci 0000:03:00.0: BAR 0 [mem >> 0xfe200000-0xfe3fffff 64bit]: assigned >> [ 2.705672] ath12k_pci 0000:03:00.0: enabling device (0000 -> 0002) >> [ 2.705885] ath12k_pci 0000:03:00.0: MSI vectors: 16 >> [ 2.705889] ath12k_pci 0000:03:00.0: Hardware name: qcn9274 hw2.0 >> [ 3.405328] ath12k_pci 0000:03:00.0: memory type 10 not supported >> [ 3.410796] ath12k_pci 0000:03:00.0: chip_id 0x0 chip_family 0xb >> board_id 0xc soc_id 0x401a2200 >> [ 3.410804] ath12k_pci 0000:03:00.0: fw_version 0x1011001d >> fw_build_timestamp 2022-12-02 01:16 fw_build_id >> QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 >> [ 3.431347] ath12k_pci 0000:03:00.0: failed to fetch board data >> for bus=pci,qmi-chip-id=0,qmi-board-id=12 from >> ath12k/QCN9274/hw2.0/board-2.bin >> [ 3.431375] ath12k_pci 0000:03:00.0: failed to fetch board.bin from QCN9274/hw2.0 >> [ 3.431386] ath12k_pci 0000:03:00.0: qmi failed to load bdf: >> [ 3.431387] ath12k_pci 0000:03:00.0: qmi failed to load board data file:-2 >> >> I'll try on my other test bed systems, but is it expected that this >> will get further than this ? > > I believe the memory type 10 message can be ignored (I've received > conflicting information on that) BTW I noticed the same warning and I reported this to the QCN9274 team a long time ago but they didn't do anything, sigh. This needs to be fixed ASAP. A driver should not print errors. -- https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2024-05-03 7:07 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <LO0P123MB4057B28CB310E5A1CEEF92F0D6002@LO0P123MB4057.GBRP123.PROD.OUTLOOK.COM>
2024-04-10 14:52 ` QCN9274 - x64 - AMD or Intel david Atkins
2024-04-10 16:57 ` Jeff Johnson
2024-04-10 19:02 ` Jeff Johnson
2024-04-28 12:50 ` david Atkins
2024-05-03 7:07 ` david Atkins
2024-04-11 8:35 ` Kalle Valo
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.